Education

23 producten


  •  -20% Mendocino Solar Motor Kit

    Mendocino Solar Motor Kit

    Niet op voorraad

    Wanneer je voor het eerst een Mendocino motor ziet kun je niet anders dan hierdoor gefascineerd zijn. Hij zweeft in de lucht en draait vanzelf, schijnbaar zonder enige toevoeging van energie. De functionele werking hiervan is eigenlijk heel simpel. De Mendocino motor is een magnetisch zwevende elektromotor aangedreven door zonne-energie. De zonnepaneeltjes leveren stroom aan de spoelen die op de rotor zijn gemonteerd, waardoor een magnetisch veld wordt gegenereerd. De sterke magneet, die aan het onderstel (het frame) is bevestigd, zorgt ervoor dat het magnetisch veld tot rotatie leidt. Dankzij de unieke magnetische ophanging is er ook bijna geen wrijving. Zorg voor voldoende licht! Hoe sterker de lichtbron, hoe sneller hij draait! Specificaties Rotatiesnelheid 300-1.500 t/min Afmetingen 13,5 x 7 x 7 cm Gewicht ca. 300 g

    Niet op voorraad

    € 49,95€ 39,95

    Leden identiek

  • Bijna uitverkocht Joy-Pi Note – 11,6` Raspberry Pi 4-gebaseerde Notebook

    JOY-iT Joy-Pi Note - 11,6" Raspberry Pi 4-gebaseerde Notebook

    Nog 1 op voorraad

    3-in-1 toepassing: Notebook, Leerplatform en Experimenteercentrum De Joy-Pi Note is het nieuwe vlaggenschip in de Joy-Pi familie. Met zijn 11.6' IPS scherm en een afneembaar, draadloos toetsenbord, brengt hij het basisconcept van de Joy-Pi in een nieuw, hoogwaardig en aantrekkelijk formaat. Met 46 cursussen en 18 projecten is de Joy-Pi Note niet alleen geschikt als experimenteercentrum, maar ook ideaal voor gebruik in het onderwijs. Met meer dan 22 geïntegreerde sensoren en modules zijn er geen grenzen aan het eigen plezier van de gebruiker om te experimenteren. Dit vereenvoudigt de kennismaking met elektrotechniek en met het programmeren. Dankzij het ingebouwde leerplatform, dat speciaal voor de Joy-Pi Note ontwikkeld werd, kunnen de geïnstalleerde onderdelen onafhankelijk van iemands eigen voorkennis bediend en aangeleerd worden. Het is ook mogelijk om via de pinnen van de Raspberry Pi, die naar buiten geleid worden, extra sensoren en modules aan te sluiten en zo ook complexere projecten uit te voeren. Natuurlijk kan de Joy-Pi Note ook gebruikt worden als een 'klassiek' notebook. Alle programma's die compatibel zijn met de Raspberry Pi 4 kunnen geïnstalleerd worden. De geïntegreerde 2 MP camera maakt bijvoorbeeld ook videoconferencing mogelijk. Alle Raspberry Pi 4 modellen kunnen gebruikt worden (we raden 4 GB RAM of hoger aan). Aan de onderkant van het apparaat vind je een vakje waar je een powerbank in kunt plaatsen om ook de Joy-Pi Note mobiel te kunnen gebruiken.. Specificaties Belangrijkste kenmerken Beeldscherm 11.6' 1920x1080 IPS LCD Camera 2 MP Speciale kenmerken Volledig uitgeruste set, volledig geïntegreerd experimenteercentrum, voorgeïnstalleerd leerplatform, afneembaar draadloos toetsenbord, geïntegreerd vak voor powerbank & accessoires Praktijklessen van het leerplatform 46 cursussen & 18 projecten voor Python en Scratch Stroomvoorziening 12 V holle stekker, 5 V USB Compatibel met Raspberry Pi 4 (4 GB en 8 GB RAM) Keyboard layouts DE (standaard) + US, UK, FR, IT, PT en Nordic Afmetingen 291 x 190 x 46 mm Gewicht 1,3 kg Meegeleverde sensoren, modules & accessoires Display 7-segment display, 16x2 LCD module, 8x8 RGB Matrix Sensors DHT11 temperatuur- en luchtvochtigheidssensor, kantelsensor, bewegingssensor, geluidssensor, aanraaksensor, RFID module, lichtsensor, ultrasone afstandssensor Motors Servo interface, stappenmotor interface, vibratiemotor Besturing Joystick, 4x4 knoppenmatrix, Raspberry Pi & PCB verbindingsschakelaar, bewegingssensor, gevoeligheidsregelaar, geluidssensor gevoeligheidsregelaar, 16x2 LCD module helderheidsregelaar Overige Relais, ventilator, GPIO uitbreiding, GPIO LED indicator, breadboard, IO/ADC/I²C/UART uitbreidingsinterface, infraroodsensor interface, zoemer, display driver Accessories RFID chip, RFID kaart, 12 V voeding, servo motor, stappenmotor, infrarood ontvanger, infrarood afstandsbediening, gelijkstroommotor met ventilatorbevestiging, HDMI aansluiting, schroevendraaier, microSD kaart (32 GB), SD kaartlezer, elektronische accessoires, draadloze muis, draadloos toetsenbord Inbegrepen Joy-Pi Note Accessories Korte handleiding Benodigdheden Raspberry Pi 4 (4 GB of 8 GB RAM)

    Nog 1 op voorraad

    € 399,00

    Leden € 359,10

  • NVIDIA Jetson Nano Developer Kit

    Nvidia NVIDIA Jetson Nano Developer Kit (B01)

    Ready to start developing Artificial Intelligence (AI) applications? The NVIDIA Jetson Nano Developer Kit makes the power of modern AI accessible to makers, developers, and students. When you think of NVIDIA, you probably think about graphics cards and GPUs, and rightfully so. Nvidia's track record guarantees that the Jetson Nano has enough power to run even the most demanding of tasks. The NVIDIA Jetson Nano Developer Kit is compatible with Nvidia's JetPack SDK and enables image classification and object detection amongst many applications. Toepassingen The NVIDIA Jetson Nano Developer Kit can run multiple neural networks in parallel for applications like: Image classification Segmentation Object detection Speech processing Specificaties GPU 128-core Maxwell CPU Quad-core ARM A57 @ 1.43 GHz Memory 4 GB 64-bit LPDDR4 25.6 GB/s Storage microSD (not included) Video Encode 4K @ 30 | 4x 1080p @ 30 | 9x 720p @ 30 (H.264/H.265) Video Decode 4K @ 60 | 2x 4K @ 30 | 8x 1080p @ 30 | 18x 720p @ 30 (H.264/H.265) Camera 1 x MIPI CSI-2 DPHY lanes Connectivity Gigabit Ethernet, M.2 Key E Display HDMI 2.0 and eDP 1.4 USB  4x USB 3.0, USB 2.0 Micro-B Interfaces GPIO, I²C, I²S, SPI, UART Dimensions 100 x 80 x 29 mm Inbegrepen NVIDIA Jetson Nano module and carrier board Small paper card with quick start and support information Folded paper stand Downloads JetPack SDK Documentation. Tutorials Online course Wiki

    € 229,00

    Leden € 206,10

  • Raspberry Pi Pico Advanced Kit met 32 modules en 32 projecten

    Elecrow Raspberry Pi Pico Advanced Kit met 32 modules en 32 projecten

    Deze Raspberry Pi Pico Advanced Kit is ontworpen voor makers die al enige elektronica kennis en programmeervaardigheden hebben en geïnteresseerd zijn in de Raspberry Pi. Indien je je denkvermogen, hands-on vaardigheden en innovatie skills wilt blijven verbeteren, dan neemt deze Raspberry Pi Pico Advanced Kit je bij de hand bij het uitwerken van verschillende scenario’s en het bouwen van meerdere toepassingen.De Raspberry Pi Pico Advanced Kit bevat een Raspberry Pi Pico H, gebaseerd op de officiële RP2040 chip, met 32 sensormodules, 1 slimme carkit en 32 Raspberry Pi Pico projecten.Met deze kit kun je verschillende interessante en praktische projecten voltooien. Daarbij worden het denkvermogen en de creativiteit van de maker voortdurend gestimuleerd.Kenmerken Geschikt voor allerlei gebruikers, van beginners tot gevorderde programmeurs 32 gedetailleerde lessen als input voor de experimenten 32 soorten sensormodules en de slimme carkit kunnen worden geconfigureerd voor interessante toepassingen De Raspberry Pi Pico is een lichtgewicht, compact en krachtig multifunctioneel microcontroller board, aangestuurd door een dual-core ARM Cortex-M0+ processor Krachtigere functies Projecten RGB kleurrijk licht: door middel van PWM pulsbreedtemodulatie wordt het LED-licht zo ingesteld dat het geleidelijk oplicht en vervolgens weer geleidelijk uitgaat, om zo een ademend lichteffect te vormen. Elektronische klok: de uur- en minuutgegevens van de klok worden weergegeven via de TM1637 4-bits digitale buis, en het klokpunt wordt zo aangestuurd dat het circulair knippert, om daarmee een elektronische klok te vormen. Kleurrijk vloeiend licht: via de GP-poort van de Pico worden 5 LED-lampjes aangestuurd om beurtelings op te lichten en vervolgens weer uit te schakelen, om op die manier een kleurrijk stromend licht te creëren. Billboard: de eerste regel van LCD1602 scrolt van rechts naar links om de tekenreeks 'Hello Pico' weer te geven, waarmee het effect van scrollen op billboards wordt gesimuleerd. Planten dokter: real-time detectie van bodemvochtigheid. Bij een normale bodemvochtigheid licht het groene lampje op en klinkt de zoemer niet. Indien de bodemvochtigheid te laag is gaat het rode lampje branden en klinkt de zoemer. Brandalarm: simuleer een brandmeldsysteem, beoordeel of er brand ontstaat door te checken of de inductiesonde van de vlamsensor de brandbron detecteert, activeer de RGB-LED’s zodat ze rood en blauw knipperen, en geef de alarminformatie weer op het LCD1602 liquid crystal display. Auto obstakelvermijding: real-time detectie van de afstand gemeten door de ultrasone afstandsensor. Wanneer de afstandswaarde lager is dan de vooraf ingestelde waarde dan wordt de auto aangestuurd om linksaf te slaan om obstakels te vermijden, om zo het effect te bereiken van obstakelvermijding bij een auto. Verkeerslicht: schakel het rode licht aan, het rode licht gaat dan weer uit nadat de 4-bits digitale buis 30 seconden heeft afgeteld. Daarna knippert het gele licht 5 keer met een tijdsinterval van 0,3 seconden. Ten slotte gaat het groene licht 10 seconden aan en vervolgens weer uit. En dan weer van voor af aan, waarmee het effect van verkeerslichten wordt gesimuleerd. Inbegrepen 1x Raspberry Pi Pico H 2x Soldeerloos breadboard met 400 aansluitgaten 5x Colorful 5 mm LED's: 1 stuks per kleur, in groen, rood, blauw, geel en wit 1x RGB-module 1x Knop 1x Geluidssensor 1x Mini PIR bewegingssensor 1x Photoresistor module 1x Laserzender 1x Passieve zoemer 1x Trillingssensor 1x Mini magnetische veermodule 1x Bodemvochtsensor 1x Draaipotentiometer 1x DC motor met male Dupont bedrading + 1x ventilatorblad 1x 9G servo 1x XY Joystick module met dubbele as 1x RC522 RFID module 1x 4 Bits digitale LED display module 1x Verkeerslicht display module 1x Roterende encodermodule 1x 1602 LCD display module (blauw) 1x Temperatuur & vochtigheidssensor 1x Regendruppels module 1x Vlammen sensor 1x OLED module 1x Membraanschakelaar toetsenbord 1x Slimme carkit 2x Crash sensor 2x Tracking sensor 1x Ultrasone sensor 1x Infrarood afstandsbediening 1x Infrarood ontvanger module 1x Micro-USB kabel (30 cm) 1x Soldeerloos breadboard met 170 aansluitgaten 1x 65 Jumper draad 1x 20 cm Dupont draad (male naar female) 1x Doorzichtige opbergdoos 2x M2,5x30 mm koperen pilaartjes 10x Kruiskopschroef met kruiskop 10x M2.5 nikkel zeskantmoeren 1x 2-inch dual-purpose schroevendraaier 1x Magneet (diameter: 8 mm, dikte: 5 mm) 1x DC stappenmotor driver board Downloads Tutorial Voorbeeldcode Inhoud en montagehandleiding

    € 59,95

    Leden € 53,96

  • JOY-iT Mega 2560 Microcontroller Learning Kit

    JOY-iT JOY-iT Mega 2560 Microcontroller Learning Kit

    De set bestaat uit 86 onderdelen. Dit zijn een Mega 2560 microcontroller board, 2 breadboards, een USB kabel, een batterijhouder, een IR afstandsbediening, een 4-cijferig segment-display, 2x 1-cijferige segment-displays, een 8x8 LED matrix, een potentiometer, een RGB LED, 5 blauwe LED's, 5 gele LED's, 5 rode LED's, 4 knoppen,een temperatuursensor (LM35), 2 kantelschakelaars, een IR ontvanger, een actieve zoemer, een passieve zoemer, 3 fotoweerstanden, een vlammensensor, 18 weerstanden (5x 1 kΩ, 8x 220 Ω, 5x 10 kΩ), een schuifregister (SN74HC595N) en 30 kabels.Kenmerken Model Mega 2560 Learning Kit Microcontroller ATmega 2560 R3 Projecten 20 verschillende projecten Handleiding Incl. projecthandleiding van 63 pagina's als download en een korte afgedrukte handleiding Specificaties Ingangsspanning 7-12 V Ingangsspanning (max.) 6-20 V Digitale IO 54 (14 met PWM) Analoge IO 16 DC Stroom IO 40 mA DC Stroom 3,3 V 50 mA Geheugen 256 kB (8 kB Bootloader) SRAM 8 kB EEPROM 4 kB Kloksnelheid 16 MHz Afmetingen 11.52 x 53,3 mm

    € 54,95

    Leden € 49,46

  •  -10% Short Circuits: The 4-Pack (Arduino-compatible Electronics Platform)

    Short Circuits: The 4-Pack (Arduino-compatible Electronics Platform)

    Get started with microcontroller based electronicsThis Arduino-compatible bundle contains the Motherboard, Digitiser, Sensor Array and RGB Matrix. With these 4 boards you have everything you need to build a clock, score counter, timer, task reminder, thermometer, humidity display, sound meter, light meter, clap trigger, colored bar graph display, animated alarm, and much more! The Motherboard has a built in real time clock module that keeps time even when unplugged. The Digitiser can display 4 digits or characters and includes 2 buttons and a potentiometer to let you control what’s being displayed, or the brightness of the display. The Sensor Array can read temperature, relative humidity, sound and light, with an SD card slot for data recording. The RGB Matrix has 16 RGB LEDs that are controlled through shift registers, so only use 3 or 4 pins of the Motherboard. MotherboardThe Motherboard is an Arduino-compatible microcontroller breakout board designed around the ATmega328P. The board comes in a solder-it-yourself kit with all the components you need to get started with microcontroller based electronics. All other boards connect to this. Based on the ATmega328P Arduino compatible On-Board RTC (Real Time Clock) FTDI Header for easy programming Bluetooth Header Terminal Block Connections DigitiserThe Digitiser is a versatile display and input board. It let’s you visualise your data. Show your sensor information, clock digits, or even keep score for your favourite card game. The Digitiser also includes some buttons and a knob to let you take control. 4x 7-Segment Displays Uses 595 Shift Registers 2 Switches and a Potentiometer 4 colored 'Mode' LEDs Chainable with other 595 Boards Terminal Block Connections Sensor ArrayAs the name suggests, the Sensor Array is an array of sensors. Measure temperature and relative humidity via the DHT11, light via the light dependant resistor, and sound via the microphone and amplifier circuit. Then you can log the data using the on-board SD card slot. DHT11 Temp & Humidity Sensor Microphone and Amplifier Circuit Light Dependent Resistor MicroSD Slot for Saving Data Logic Level Converter Circuit Terminal Block Connections RGB MatrixAdd color to your project by controlling 16 red, 16 green and 16 blue LEDs with just 3 pins of your microcontroller. The RGB Matrix uses shift registers, a matrix and switching transistors, so there’s plenty to learn and explore. 4x4 (16) RGB LEDs Uses 595 Shift Registers Chainable with other 595 Boards Transistor Switches Terminal Block Connections Downloads (Manuals) Motherboard Digitiser Sensor Array RGB Matrix

    € 99,95€ 89,95

    Leden € 80,96

  • Joy-Pi Advanced – Ontwikkelplatform voor Raspberry Pi, Arduino en ESP32

    JOY-iT Joy-Pi Advanced – Ontwikkelplatform voor Raspberry Pi, Arduino en ESP32

    De Joy-Pi Advanced is een compact en krachtig instrument waarmee je snel en eenvoudig je projecten kunt realiseren. Of je nu veel of weinig ervaring hebt, met de Joy-Pi Advanced kun je je creativiteit de vrije loop laten. Dankzij de compatibiliteit met een groot aantal platformen, waaronder Raspberry Pi, Raspberry Pi Pico, Arduino Nano, BBC micro:bit en NodeMCU ESP32, kun je eenvoudig en snel toegang krijgen tot het platform van je voorkeur. Daarnaast heeft de Joy-Pi Advanced meer dan 30 stations, lessen en modules, waardoor je een onbeperkt aantal manieren hebt om je projecten uit te voeren. Met het zelfontwikkelde leercentrum kun je niet alleen je vaardigheden verbeteren, maar ook nieuwe projecten maken. Het leercentrum biedt een schat aan informatie en tutorials die je stap voor stap door je projecten begeleiden. Joy-Pi Advanced wordt in het bijzonder gekenmerkt door zijn intelligente schakeleenheden, die een uitgebreid gebruik van de beschikbare pinnen mogelijk maken. In totaal zijn er drie schakeleenheden geïntegreerd, elk voorzien van 12 individuele schakelaars die zorgen voor een nauwkeurige aansturing van de aangesloten sensoren en modules. Dit systeem lost het bekende probleem van het beperkte aantal pinnen op dat optreedt bij conventionele microcontrollers. Met de schakeleenheden kun je een groot aantal sensoren en modules parallel aansturen door ze afzonderlijk aan en uit te schakelen. Dit simuleert meervoudige pintoewijzing, waardoor je het volledige vermogen van je projecten kunt benutten zonder afbreuk te doen aan de functionaliteit. Door onze innovatieve adapter boards en het micro:bit slot te combineren, bereiken we naadloze compatibiliteit met een breed scala aan microcontrollers zoals Raspberry Pi Pico, NodeMCU ESP32, micro:mit en Arduino Nano. De speciaal ontwikkelde adapterkaarten zijn zo ontworpen dat ze perfect passen bij de betreffende microcontroller. Door de microcontroller op het juiste adapterboard aan te sluiten en deze vervolgens in het micro:bit slot te steken, wordt de Joy-Pi Advanced snel en eenvoudig compatibel met de verschillende microcontrollers. Dit zorgt voor een naadloze integratie van het platform van je voorkeur en de mogelijkheid om de sterke punten van de verschillende microcontrollers te combineren in je projecten. Op deze manier kun je je volledig richten op je creatieve projecten zonder dat je je zorgen hoeft te maken over de compatibiliteit van verschillende microcontrollers. De Joy-Pi Advanced vereenvoudigt het ontwikkelproces en geeft je de mogelijkheid om je projecten flexibel en individueel te ontwerpen. Kenmerken Sterk geïntegreerd ontwikkelplatform & leercentrum Snel, eenvoudig & draadloos combineren van verschillende sensoren & actuatoren Installatieoptie voor Raspberry Pi 4 Compatibel met verschillende microcontrollers Zelfontwikkeld, didactisch leerplatform voor Raspberry Pi & Windows Specificaties Compatibel met Raspberry Pi 4, Arduino Nano, NodeMCU ESP32, BBC micro:bit, Raspberry Pi Pico Geïnstalleerde sensoren, actuatoren & componenten 39 Leerplatform Meer dan 40 items in de kennisdatabase, 10 projecten, 10 lessen, 14 visies Displays 7-segment display, 16x2 display, 1,8' TFT-display, 0,96' OLED-display, 8x8 RGB-matrix Sensoren DS18B20, schoksensor, hallsensor, barometer, geluidssensor, gyroscoop, PIR-sensor, Lichtbarrière, NTC, Lichtsensor, 6x aanraaksensor, kleurensensor, ultrasone afstandssensor, DHT11 temperatuur- & vochtigheidssensor Controle Joystick, 5x schakelaars, potentiometer, draaiencoder, 4x4 knoppenmatrix, relais, PWM-ventilator Motoren Servo-interface, Stappenmotorinterface, Trilmotor Meet- en conversiemodules Analoog-digitaalomzetter, niveauomzetter, voltmeter, variabele spanningsbron Andere onderdelen RTC real-time klok, zoemer, EEPROM-geheugen, infrarood ontvanger, breadboard, RFID-lezer Adapterkaarten Adapter voor NodeMCU ESP32, Arduino Nano & Raspberry Pi Pico, Board connectors voor Raspberry Pi & externe boards Elektronische onderdelen Infrarood afstandsbediening, RFID-chip, RFID-kaart, 6x krokodillenklemmen, microSD-kaartlezer, servomotor, stappenmotor, 32 GB microSD-kaart Onderdelen 40x weerstanden, 3x groene LED's, 3x gele LED's, 3x rode LED's, 1x transistor, 5x knoppen, 1x potentiometer, 2x condensatoren Andere accessoires Schroevenassortiment, schroevendraaier, accessoire-opbergtas, voeding & voedingskabel, servo bevestiging Stroomvoorziening Ingebouwde voeding: 36 W, 12 V, 3 A Behuizingsconnector: Kleine apparaat stekker C8 Spanningsuitgangen 12 V, 5 V, 3,3 V, variabele spanningsuitgang (2-11 V) Databussen & signaaluitgangen I²C, SPI, Analoog naar digitaal converter Batterij (RTC) CR2032 Afmetingen 327 x 200 x 52 mm Vereist Raspberry Pi 4 Downloads Joy-Pi website Datasheet Manual

    € 369,00

    Leden € 332,10

  •  -24% Arduino Studenten Kit

    Arduino Arduino Studenten Kit

    De Arduino Student Kit is een hands-on en stap-voor-stap hulpmiddel bij het leren op afstand door kinderen vanaf 11 jaar: raak bekend met de basiskennis van elektronica, programmeren en coderen thuis. Omdat de kit u stapsgewijs begeleidt is er geen voorkennis of ervaring nodig. Docenten kunnen met deze kits hun klas op afstand les geven, en ouders kunnen de kit gebruiken als een tool bij thuisonderwijs aan hun kind, en hen daarmee in hun eigen tempo laten leren. Door de doelgerichte lessen en toegankelijke experimenten raken ze vertrouwd met programmeren en elektronica.Leer de basisprincipes van programmeren, coderen en elektronica, inclusief stroom, spanning en digitale logica. Er is geen minimum kennis of ervaring nodig omdat de kit stapsgewijze begeleiding biedt.U krijgt voor één persoon alle hardware en software erbij, wat deze kit ideaal maakt om te gebruiken voor lesgeven op afstand, thuisonderwijs, en voor zelfstudie. Er zijn stapsgewijze lessen, oefeningen, en voor een complete en meer uitgebreide leerervaring is er ook extra inhoud. Daarin is er nog aandacht voor ontwikkelingen, concepten en interessante feiten over elektronica, technologie en programmeren.De lessen en projecten kunnen worden aangepast aan de individuele vaardigheden, waardoor er thuis op eigen niveau kan worden gestudeerd. De kit kan ook worden geïntegreerd in verschillende andere vakken zoals natuurkunde, scheikunde en zelfs geschiedenis. Het zou in feite voor een heel semester genoeg inhoud geven.Hoe docenten de kit kunnen gebruiken voor afstandsonderwijsHet online platform bevat alles wat u nodig heeft om op afstand les te geven: exclusieve inhoud voor studiebegeleiding, tips voor het leren op afstand, negen lessen van 90 minuten, en twee open einde projecten. Elke les bouwt voort op de vorige en biedt aanvullende opties om de vaardigheden en concepten toe te passen die de studenten eerder hebben geleerd. Ze krijgen ook een logboek dat ze kunnen bijhouden terwijl ze de lessen volgen.Iedere les begint met een overzicht, de geschatte benodigde tijd en de leerdoelen. Tijdens elke les zijn er tips en informatie, wat het leren eenvoudiger maakt. Belangrijke antwoorden en aanvullende suggesties worden ook gegeven.Hoe de kit ouders helpt hun kinderen thuisonderwijs te gevenDit is uw hands-on en stap-voor-stap hulpmiddel bij afstandsonderwijs dat uw kind helpt thuis de basiskennis van programmeren, coderen en elektronica op te doen. Als ouder heeft u geen voorkennis of ervaring nodig, omdat u stapsgewijs wordt begeleid. De kit is rechtstreeks gekoppeld aan het curriculum, zodat u erop kunt vertrouwen dat uw kinderen leren wat ze zouden moeten leren, en het biedt hen de mogelijkheid om vertrouwd te raken met programmeren en elektronica. U helpt ze ook om basis vaardigheden te leren, zoals kritisch denken en problemen oplossen.Zelfstudie met de Arduino Student KitStudenten kunnen deze kit gebruiken om basiskennis van elektronica, programmeren en coderen op te doen. Omdat er bij alle lessen stapsgewijze instructies zijn is het voor hen eenvoudig om zelfstandig de les te volgen en te studeren. Ze kunnen in hun eigen tempo werken, plezier hebben met allerlei concrete projecten, en meer bekend raken met de materie terwijl ze bezig zijn. Ze hebben geen voorkennis nodig omdat alles duidelijk wordt uitgelegd, de codering al vooraf is geschreven, en er een schat aan informatie is om te raadplegen.De Arduino Student Kit wordt geleverd met diverse onderdelen en componenten waarmee tijdens het voltooien van de lessen en de projecten schakelingen zullen worden gebouwd.Inbegrepen in de kit Toegangscode naar exclusieve online content, inclusief studiebegeleiding, stapsgewijze lessen, en extra materialen zoals diverse bronnen, ontwikkelingen en een digitaal logboek met oplossingen. 1x Arduino Uno 1x USB-kabel 1x board montagevoet 1x multimeter 1x 9 V batterij houder 1x 9 V batterij 20x LED's (5x rood, 5x groen, 5x geel & 5x blauw) 5x weerstanden 560 Ω 5x weerstanden 220 Ω 1x breadboard 400 points 1x weerstand 1 kΩ 1x weerstand 10 kΩ 1x kleine servomotor 2x potentiometers 10 kΩ 2x knop potentiometers 2x condensatoren 100 uF solid core jumper draden 5x drukknoppen 1x fototransistor 2x weerstanden 4,7 kΩ 1x jumper draad zwart 1x jumper draad rood 1x temperatuursensor 1x piezo 1x jumper draad female naar male rood 1x jumper draad female naar male zwart 3x moeren en bouten

    € 104,95€ 79,95

    Leden identiek

  • Arduino Braccio ++ RP2040 powered Robot Arm

    Arduino Arduino Braccio ++ RP2040 powered Robot Arm

    Niet op voorraad

    De volgende evolutie van de Tinkerkit Braccio-robot, Arduino Braccio ++ is een robotarm die binnen 'Arduino Education' ontworpen is voor het hoger onderwijs als technische scholen en universitaire technologie-instituten. Uiteraard kan de nieuwe Braccio ook gebruikt worden door gevorderde middelbare scholieren en studenten die wetenschappen, industriële wetenschap of technologie studeren. De Braccio ++ is volledig geoptimaliseerd en kan op verschillende manieren worden gemonteerd voor meerdere taken, zoals het verplaatsen van objecten, het monteren van een camera en het volgen van uw bewegingen, of het bevestigen van een zonnepaneel en het volgen van de beweging van de zon. De toepassingen zijn bijna onbeperkt. Studenten leren toepassingen van natuurkundige concepten in het echte leven door een voorwerp op te tillen, te plaatsen en te draaien. Deze concepten omvatten bewegingen, krachten, koppel, overbrengingsverhoudingen, stabiliteit en het gewicht van de nuttige last. De Braccio ++ heeft een nieuwe Braccio Carrier met LCD-scherm en nieuwe RS485-servomotoren. Downloads Braccio Carrier

    Niet op voorraad

    € 499,00

    Leden € 449,10

  •  -25% Electric Paint Lamp Kit

    Bare Conductive Electric Paint Lamp Kit

    The Electric Paint Lamp Kit is a great gift! Transform any piece of paper into a touch-sensitive lamp with Electric Paint! Make three paper lamps with no tools, no programming, no special skills required. Included 1x Light Up Board 1x Electric Paint 10ml Tube 1x Micro USB Cable 1x Touch Lamp Template 1x Dimmer Lamp Template 1x Proximity Lamp Template 1x Instruction Test Sheet Transform a paper template into a beautiful lamp in three easy steps. Paint, plug, and play! Use Electric Paint to create custom touch-sensitive buttons connected to our Light Up Board and then use our lampshades to bring your lamp to life. LEVEL: Beginner The Electric Paint Lamp Kit is easy to use and makes a perfect gift. The Touch, Dimmer, and Proximity lamps all show off different aspects of Electric Paint and the Light Up Board and are perfect for your home, office or workshop. About Electric Paint Your design and electronics projects are about to change forever with this easy to use electrically conductive paint. Paint circuits or use as a conductive adhesive on almost anything including paper, plastic, textiles and conventional electronics. About the Light Up Board The Light Up Board is the heart of the Electric Paint Lamp Kit. It works straight out of the box, is powered by USB and requires no programming or special tools. The board’s six bright LEDs and three different modes provide the light for your lamps and the super easy connector system means that you can create lamps on any sheet material.

    € 52,95€ 39,95

    Leden identiek

  • Sipeed MAix Bit Suit with LCD and Camera

    Seeed Studio Sipeed MAix Bit Suit with LCD and Camera

    Niet op voorraad

    Sipeed AI & IoT board is not only hardware but also provide an end-to-end, hardware + software infrastructure for the deployment of AI-based solutions.Sipeed AI & IoT board can be used for a growing number of use-cases such as: predictive maintenance machine vision voice recognition anomaly detection robotics Specifications CPU: RISC-V Dual Core 64bit, 400Mh adjustable Powerful dual-core 64-bit open architecture-basedprocessor with rich community resources Debugging Support High-speed UART and JTAG interface for debugging GPIO interface All GPIOs connected to header 2*20 2.54mm Micro SD card(TF card) slot Support Self-elastic card holder One-click Download circuit Just connect the USB typeC cable to complete the downloadOnboard CH340, 2Mbps baud rate DVP Camera connector 24P 0.5mm FPC connector LCD connector 8bit MCU LCD 24P 0.5mm FPC connector Button RST button and USR button CPU 1st competitive RISC-V chip 28nm process, dual-core RISC-V 64bit IMAFDC, on-chip huge 8MB high-speed SRAM, 400MHz frequency (able up to 800MHz) KPU (Neural Network Processor): 64 KPU 576bit width convolution kernels any form of activation function. 0.25TOPS (trillion operations per second) @ 0.3W 400MHz, When overclocked to 800MHz, it offers 0.5TOPS APU (Audio Processor) 8 mics up to 192 kHz sample rate FFT unit Flexible FPIOA (Field Programmable IO Array), you can map 255 functions to all 48 GPIOs on the chip DVP camera and MCU LCD interface, you can connect a DVP camera, run your algorithm, and display on LCD Other accelerators and peripherals AES Accelerator SHA256 Accelerator FFT Accelerator (not APU's one) OTP UART WDT IIC SPI I2S TIMER RTC PWM SoftwareThe Sipeed AI & IoT board supports original standalone SDK, FreeRTOS SDK based on C/C++.You can port micropython on it: http://en.maixpy.sipeed.com/. It also supports FPIOA, GPIO, TIMER, PWM, Flash, OV2640, LCD. And it has zmodem, vi, SPIFFS on it, so that you can edit python directly or sz/rz file to board.Seedstudio offers even more support to your project with their GitHub contributions:https://github.com/sipeed/MaixPyhttps://github.com/sipeed/MaixPy_Doc_Us_En_Backup Deep LearningThe Sipeed AI & IoT board supports a fixed-point model that the mainstream training framework trains, according to specific restriction rules, and have a model compiler to compile models to its model format.It supports tiny-yolo, mobilenet-v1, and, TensorFlow Lite! Many TensorFlow Lite model can be compiled and run on the Sipeed AI & IoT board!Software Features Support FreeRtos and Standard development kit Support MicroPython on M1 Machine vision based on convolutional neural network High-performance microphone array processor Electrical Specifications Supply voltage 4.8 V ~ 5.2 V Supply current > 600 mA Temperature rise < 30 K Working temperature - 30 ℃ ~ 85 ℃

    Niet op voorraad

    € 34,95

    Leden € 31,46

  • Bijna uitverkocht SparkFun Inventor's Kit voor Arduino Uno v4.1

    SparkFun SparkFun Inventor's Kit voor Arduino Uno v4.1

    Nog 1 op voorraad

    De online gids bevat stap-voor-stap instructies voor het bouwen van elk project en circuit met de bijgeleverde onderdelen. Er wordt ook voorbeeldcode gegeven om het gemakkelijker te maken aan de slag te gaan. De nieuwe concepten en componenten die in elk project worden geïntroduceerd, worden uitgelegd op het punt van gebruik, en er zijn ook tips voor het oplossen van problemen om hulp te bieden in het geval er iets misgaat.Om de kit veilig te maken voor beginners, is solderen verwijderd. SparkFun Inventor's Kit voor Arduino Uno v4.1 wordt aanbevolen voor iedereen vanaf 10 jaar die op zoek is naar een Arduino starterkit.Inclusief 1x Arduino Uno 1x Arduino en Breadboard Houder 1x wit soldeerloos Breadboard 1x SparkFun Mini Schroevendraaier 1x Wit-op-zwart LCD Scherm (met headers) 1x SparkFun Motor Driver (met headers) 2x Rubber wielen 2x Tandwielmotoren 1x kleine servo 1x Ultrasone Sensor 1x TMP36 Temp Sensor 1x 6' SparkFun USB-kabel Jumper Draden 1x fotocel 1x driekleurige LED Rode, blauwe, gele en groene LED's Rode, Blauwe, Gele en Groene Tactiele Knoppen 1x 10K Trimpot 1x Mini Netschakelaar 1x Piëzo luidspreker 1x AA Batterij Houder 330 Ω en 10K Ω Weerstanden

    Nog 1 op voorraad

    € 114,95

    Leden € 103,46

  •  -19% Seeed Studio Grove Beginner Kit for Arduino (Education Add-on Pack)

    Seeed Studio Seeed Studio Grove Beginner Kit for Arduino (Education Add-on Pack)

    Toepassingen Geschikt voor Arduino beginners Geschikt voor infraroodsturing en bewegingsdetectie Geschikt om aan de slag te gaan met open-source hardware en Arduino codering Deel Lijst 1 x Grove - Waterverstuiving 1 x Grove - Mini Ventilator 1 x Grove - Servo 1 x Grove - Ultrasone Afstandssensor 1 x Grove - Infrarood Ontvanger 1 x Grove - Mini PIR Bewegingssensor 1 x Grove - Groene Wikkel 1 x Grove - Blauwe Wikkel 5 x Grove kabel 1 x Infrarood Remote Control Key 1 x Ultrasone sensor beugelset 1 x motorbeugelset 1 x Servo Basis Let op: Dit is een uitbreidingsset voor de Seeed Studio Grove Beginner Kit voor Arduino.

    € 52,95€ 42,95

    Leden identiek

  •  -21% Seeed Studio Deep Learning Starter Kit for Jetson Nano

    Seeed Studio Seeed Studio Deep Learning Starter Kit for Jetson Nano

    Features 32GB High-performance MicroSD card 5 V 4 A power supply with 2.1mm DC barrel connector 2-pin jumper Raspberry Pi camera module V2 Micro-B To Type-A USB cable with DATA enabled

    € 62,95€ 49,95

    Leden identiek

  • ROBOTIS TurtleBot3 Burger (incl. Raspberry Pi 4)

    ROBOTIS TurtleBot3 Burger (incl. Raspberry Pi 4)

    Niet op voorraad

    World’s Most Popular ROS PlatformTurtleBot is the most popular open source robot for education and research. The new generation TurtleBot3 is a small, low cost, fully programmable, ROS based mobile robot. It is intended to be used for education, research, hobby and product prototyping.Affordable CostTurtleBot was developed to meet the cost-conscious needs of schools, laboratories and companies. TurtleBot3 is the most affordable robot among the SLAM-able mobile robots equipped with a 360° Laser Distance Sensor LDS-01.Small SizeThe dimension of TurtleBot3 Burger is only 138 x 178 x 192 mm (L x W x H). Its size is about 1/4 of the size of the predecessor. Imagine keeping TurtleBot3 in your backpack and develop your program and test it anywhere you go.ROS StandardThe TurtleBot brand is managed by Open Robotics, which develops and maintains ROS. Nowadays, ROS has become the go-to platform for all the roboticists around the world. TurtleBot can be integrated with existing ROS-based robot components, but TurtleBot3 can be an affordable platform for whom want to get started learning ROS.ExtensibilityTurtleBot3 encourages users to customize its mechanical structure with some alternative options: open source embedded board (as a control board), computer and sensors. TurtleBot3 Burger is a two-wheeled differential drive type platform but it is able to be structurally and mechanically customized in many ways: Cars, Bikes, Trailers and so on. Extend your ideas beyond imagination with various SBC, sensors and motors on a scalable structure.Modular Actuator for Mobile RobotTurtleBot3 is able to get a precise spatial data by using 2 DYNAMIXEL’s in the wheel joints. DYNAMIXEL XM series can be operated by one of 6 operating modes (XL series: 4 operating modes): Velocity control mode for wheels, Torque control mode or Position control mode for joint, etc. DYNAMIXEL can be used even to make a mobile manipulator which is light but can be precisely controlled with velocity, torque and position control. DYNAMIXEL is a core component that makes TurtleBot3 perfect. It is easy to assemble, maintain, replace and reconfigure.Open Control Board for ROSThe control board is open-sourced in hardware wise and in software wise for ROS communication. The open source control board OpenCR1.0 is powerful enough to control not only DYNAMIXEL’s but also ROBOTIS sensors that are frequently being used for basic recognition tasks in cost effective way. Various sensors such as Touch sensor, Infrared sensor, Color sensor and a handful more are available. The OpenCR1.0 has an IMU sensor inside the board so that it can enhance precise control for countless applications. The board has 3.3 V, 5 V, 12 V power supplies to reinforce the available computer device lineups.Strong Sensor LineupsTurtleBot3 Burger uses enhanced 360° LiDAR, 9-Axis Inertial Measurement Unit and precise encoder for your research and development.Open SourceThe hardware, firmware and software of TurtleBot3 are open source which means that users are welcomed to download, modify and share source codes. All components of TurtleBot3 are manufactured with injection molded plastic to achieve low cost, however, the 3D CAD data is also available for 3D printing.Specifications Maximum translational velocity 0.22 m/s Maximum rotational velocity 2.84 rad/s (162.72 deg/s) Maximum payload 15 kg Size (L x W x H) 138 x 178 x 192 mm Weight (+ SBC + Battery + Sensors) 1 kg Threshold of climbing 10 mm or lower Expected operating time 2h 30m Expected charging time 2h 30m SBC (Single Board Computers) Raspberry Pi 4 (2 GB RAM) MCU 32-bit ARM Cortex-M7 with FPU (216 MHz, 462 DMIPS) Actuator XL430-W250 LDS (Laser Distance Sensor) 360 Laser Distance Sensor LDS-01 or LDS-02 IMU Gyroscope 3 AxisAccelerometer 3 Axis Power connectors 3.3 V/800 mA5 V/4 A12 V/1 A Expansion pins GPIO 18 pinsArduino 32 pin Peripheral 3x UART, 1x CAN, 1x SPI, 1x I²C, 5x ADC, 4x 5-pin OLLO DYNAMIXEL ports 3x RS485, 3x TTL Audio Several programmable beep sequences Programmable LEDs 4x User LED Status LEDs 1x Board status LED1x Arduino LED1x Power LED Buttons and Switches 2x Push buttons, 1x Reset button, 2x Dip switch Battery Lithium polymer 11.1 V 1800 mAh / 19.98 Wh 5C PC connection USB Firmware upgrade via USB / via JTAG Power adapter (SMPS) Input: 100-240 VAC 50/60 Hz, 1.5 A @maxOutput: 12 VDC, 5 A Downloads ROS Robot Programming GitHub E-Manual Community

    Niet op voorraad

    € 739,00

    Leden identiek

  • Oxocard Connect Innovator Kit

    Oxocard Oxocard Connect Innovator Kit

    With this comprehensive complete set, you can now enter the fascinating world of electronics. In addition to an Oxocard Connect and a breadboard cartridge, it contains 96 electronic components with which you can build a variety of electronic circuits. Features Free and unlimited access to the nanopy.io editor with a variety of scripts that you can transfer to your Oxocard Connect at the touch of a button. Electronics course with 15 experiments that show you step by step how to switch LEDs, connect a servo, generate acoustic signals with a piezo and much more. Oxocard Connect High quality microcontroller device with TFT screen, glass cover, joystick, USB-C, as well as revolutionary 16-pin cartridge slot. The Oxocard Connect represents the next generation of small experimental computers. The universal cartridge slot allows ready-made or self-developed boards to be brought to life instantly by simply plugging them in. Each card comes with drivers and demo programs installed and automatically loaded and started when plugged in. Breadboard Cartridge With the Breadboard you can quickly plug in your own circuits. A plug-in board with 17 rows is available for this purpose. Connections: two analog inputs, five digital ports, I²C, SPI, GND/V3.3. access to the 5 V power source of the port. Red LEDs are attached to the digital pins. 5 V can also be injected to power the Oxocard Connect without USB. Included 1x Oxocard Connect 1x Breadboard Cartridge Electronic components 1x PIR-Sensor (Motion detector) 1x Thermistor 10 kΩ (Temperature sensor) 1x Photoresistor 10 kΩ (Light sensor) 1x Potentiometer 1x Mikroservo SG92R 1x Piezo (Acoustic signals) 3x LED (green, yellow, red) 2x Buttons 9x Resistances 75x Cables (angled) – various colors and lengths

    € 89,95

    Leden € 80,96

  • Unitree Quadruped Go1 Edu Plus (NVIDIA NX)

    Unitree Quadruped Go1 Edu Plus (NVIDIA NX)

    Unitree Go1 series consists of quadruped robots for the research & development of autonomous systems in the fields of human-robot interaction (HRI), SLAM & transportation. Due to the four legs, as well as the 12DOF, this robot can handle a variety of different terrains. The Go1 comes with a perfected drive & power management system, which enables a speed (depending on the version) of up to 3.7 m/s or 11.88 km/h with an operating time of up to 2.5 hours. Furthermore, the motors have a torque of 23.70N.m at the body/thighs and 35.55N.m at the knees, which also allow jumps or backflips. Features High Dynamics 17 km/h Intelligent Side-Follow System (ISS) Super Sensory System (SSS) 10-view Detection AI Detection, Human Recognition, etc. Flexible and adaptive Joints Long Endurance Specifications Light and Compact Weight: 12 kg Size (folded): 0.588 x 0.29 x 0.22 m High Performance Max Speed: 4.7 m/s (17 kmh or 10.6 mph) Intelligent Side Follow System (Adopt Patented Wireless Vector Positioning and Control Technology) Robot dog can walk alongside its owner and not only follow The human-machine interaction is both harmonious and safe Super Sensory System Full View Coverage 5 Sets Fish-Eye Stereo Depth Cameras + AI Post-processing + 3 Sets of Hypersonic Sensors Lens Angle: 150 x 170° Built-in Powerful AI 16-core CPU + GPU (384 Cores, 1.5 TFLOPS) ISS and SSS Function Cooperatively Strong & Reliable Power System New Power Joint with Super Lightweight Low Noise and Long Life Heat Pipe Cooling System Built in the Knee Joint Motor Body/thigh joints: C1-8: 520 g 23.70N.m Knee Joint: C1-8 x 1.5 ratio 35.55N.m Unitree Go1 Variants The Go1 series has 3 variants (Go1 Air, Go1 Pro and Go1 Edu), which differ a little technically. The differences are mainly the processors and sensor systems, the Air and Pro variant works, depending on the model, with one or 3x (4x 1.43 GHz 128 Cores 0.5 T) processor as well as with 1 or 5 super sensor systems. Both variants are equipped with 3 ultrasonic sensors. The Go1 Edu variant has up to 3 nano processors, 5 super sensor systems, and 4 ultrasonic sensors. In contrast, Edu Plus is equipped with an Nvidia Jetson Xavier NX as standard. Model Comparison   Go1 Air Go1 Pro Go1 Edu Go1 Edu Plus SSS 1 Super-sensing system 1 set 5 sets 5 sets 5 sets Sensing calculation 1x (4x 1.43 GHz 128 Cores 0.5 T) 3x (4x 1.43 GHz 128 Cores 0.5 T) 3 Jetson Nano 2 Jetson Nano + 1 NVIDIA Jetson NX ISS 1 Intelligent Concomitant ✓ ✓ ✓ ✓ RTT 1 Pictures Transaction ✓ ✓ ✓ ✓ Charger 24 V, 4 V 24 V, 6 V 24 V, 6 V 24 V, 6 V Remote Control ✓ ✓ ✓ ✓ Load ≈3 kg ≈3 kg ≈5 kg (max ~10 kg) ≈5 kg (max ~10 kg) Heat Pipe Assisted Heat Dissipation ✓ ✓ ✓ ✓ Motion Speed 0~2.5 m/s 0~3.5 m/s 0~3.7 m/s (max ~5 m/s) 0~3.7 m/s (max ~5 m/s) Battery 1x 1x 1x 1x Graphical Programming Interface ✓ ✓ ✓ ✓ Scientific Programming Interface     ✓ ✓ Python Programming Interface     ✓ ✓ HAI 1 Human Sensing     ✓ ✓ APP Top View   ✓ ✓ ✓ 4G     ✓ ✓ Foot-end Physical Force Sensor     ✓ ✓ Multifunctional Peripheral Expansion Interface     ✓ ✓ Radar     2D or 3D optional 2D or 3D optional Included 1x Unitree Go1 1x Unitree Go1 Battery 1x Unitree Go1 Charger 1x Unitree Go1 Remote Controller Downloads User Manual GitHub

    € 14.399,00

    Leden identiek

  • Arduino Science Kit Rev3

    Arduino Arduino Science Kit Rev3

    Krijg toegang tot de wereld van interactief leren met de robuuste hardware en software van de Science Kit R3. Met hierin de Arduino Nano RP2040 Connect, de Arduino Science Carrier R3, en een indrukwekkende reeks sensoren heeft u alles wat u nodig heeft om een boeiende educatieve reis te maken. Gelijktijdig overbrugt de Science Journal app moeiteloos de kloof tussen de theorie en de praktijk, waardoor real-time data verzameling, registratie en interpretatie mogelijk wordt. De kit tilt uw leerervaring naar een hoger niveau door het begrip van complexe natuurkundige concepten te bevorderen met hands-on experimenten. Hij stimuleert wetenschappelijke kennis, en scherpt het kritisch denken aan door toepassingsscenario's te bieden die in praktijk ook voorkomen. Met zijn intuïtieve tutorial kunnen zowel docenten als studenten gemakkelijk met de wetenschappelijke experimenten aan de slag gaan. Kenmerken Hands-on experimenteel leren: voer fysieke experimenten uit en zet abstracte natuurkundige concepten om naar tastbare en interactieve ervaringen. Realtime gegevensverzameling en -analyse: dankzij de integratie met de Science Journal app kunnen studenten met de kit realtime gegevens verzamelen, vastleggen en interpreteren met mobiele apparaten, waardoor hun kennis en onderzoeksvaardigheden worden versterkt. Leraar- en leerlingvriendelijk ontwerp: doordat de kit is uitgerust met vooraf geïnstalleerde software is er geen voorkennis van codering of elektronica nodig. De kit beschikt ook over Bluetooth connectiviteit voor eenvoudige gegevensoverdracht van het Arduino board naar de mobieltjes van de studenten. Uitgebreid sensor ecosysteem: de kit wordt geleverd met meerdere sensoren, die een breed scala aan mogelijkheden voor gegevensverzameling bieden, en aan te passen zijn aan veranderende onderwijsbehoeften. Gratis begeleidende cursussen – Explore Physics: bevat een intuïtieve cursusgids die docenten en studenten helpt bij het gebruik van de kit, het presenteren en analyseren van gegevens, en het evalueren van experimentele resultaten. Deze cursussen helpen studenten ook om hun wetenschappelijke ontdekkingen doelgericht te communiceren. Uitgebreide onderwijsondersteuning: met zijn intuïtieve tutorial vereenvoudigt de Arduino Science Kit R3 het instructieproces voor docenten. Deze geeft niet alleen instructies over het gebruik van de kit, maar helpt ook bij het presenteren, analyseren en evalueren van gegevens, zodat studenten hun wetenschappelijke bevindingen effectief kunnen presenteren. Specificaties Hardware Arduino Nano RP2040 Connect Arduino Science Carrier R3 Ingebouwde sensoren: Luchtkwaliteit, temperatuur, luchtvochtigheid en druk IMU: 6-assige lineaire accelerometer, gyroscoop en magnetometer Nabijheidsmeting, omgevingslicht, lichtkleur Spanning of elektrisch potentiaalverschil Elektrische stroom Weerstand Functiegeneratoren om het effect van frequentie, amplitude en fase op een geluidsgolf te zien en te horen Sensor voor de intensiteit van omgevingsgeluid Ports 2x Grove analoge ingangen (voor externe temperatuur-probe sensor) 2x Grove I²C-poorten (voor externe afstand en ping-echo sensor) 1x Batterij JST-connector 2x Uitgangspoorten aangesloten op het laag vermogenssignaal van functiegeneratoren (toekomstige generatie) 1x 3,3 V Uitgangspoort en aarde 2x Luidsprekerpoorten aangesloten op functiegeneratoren Anders Tweezijdig afgewerkte kabel van 50 cm (blauw): krokodillenklemmen aan het ene uiteinde, banaanstekker aan het andere Tweezijdig afgewerkte kabel van 20 cm (zwart): krokodillenklemmen aan het ene uiteinde, banaanstekker aan het andere Tweezijdig afgewerkte kabel van 20 cm (rood): krokodillenklemmen aan het ene uiteinde, banaanstekker aan het andere Klittenband strips Siliconen standaards Externe temperatuur-probe sensor Ultrasone afstand sensor Grove 4-polige kabel met slot x2 (L=200 mm) USB-C kabel Tweezijdig afgewerkte kabel van 50 cm (geel): krokodillenklemmen aan het ene uiteinde, banaanstekker aan het andere 2x Luidsprekers Kabel voor batterijhouder met JST-connector Batterijhouder voor vier 1V5 AA-batterijen

    € 239,00

    Leden € 215,10

  • Unitree Quadruped Go1 Edu

    Unitree Quadruped Go1 Edu

    Unitree Go1 series consists of quadruped robots for the research & development of autonomous systems in the fields of human-robot interaction (HRI), SLAM & transportation. Due to the four legs, as well as the 12DOF, this robot can handle a variety of different terrains. The Go1 comes with a perfected drive & power management system, which enables a speed (depending on the version) of up to 3.7 m/s or 11.88 km/h with an operating time of up to 2.5 hours. Furthermore, the motors have a torque of 23.70N.m at the body/thighs and 35.55N.m at the knees, which also allow jumps or backflips. Features High Dynamics 17 km/h Intelligent Side-Follow System (ISS) Super Sensory System (SSS) 10-view Detection AI Detection, Human Recognition, etc. Flexible and adaptive Joints Long Endurance Specifications Light and Compact Weight: 12 kg Size (folded): 0.588 x 0.29 x 0.22 m High Performance Max Speed: 4.7 m/s (17 kmh or 10.6 mph) Intelligent Side Follow System (Adopt Patented Wireless Vector Positioning and Control Technology) Robot dog can walk alongside its owner and not only follow The human-machine interaction is both harmonious and safe Super Sensory System Full View Coverage 5 Sets Fish-Eye Stereo Depth Cameras + AI Post-processing + 3 Sets of Hypersonic Sensors Lens Angle: 150 x 170° Built-in Powerful AI 16-core CPU + GPU (384 Cores, 1.5 TFLOPS) ISS and SSS Function Cooperatively Strong & Reliable Power System New Power Joint with Super Lightweight Low Noise and Long Life Heat Pipe Cooling System Built in the Knee Joint Motor Body/thigh joints: C1-8: 520 g 23.70N.m Knee Joint: C1-8 x 1.5 ratio 35.55N.m Unitree Go1 Variants The Go1 series has 3 variants (Go1 Air, Go1 Pro and Go1 Edu), which differ a little technically. The differences are mainly the processors and sensor systems, the Air and Pro variant works, depending on the model, with one or 3x (4x 1.43 GHz 128 Cores 0.5 T) processor as well as with 1 or 5 super sensor systems. Both variants are equipped with 3 ultrasonic sensors. The Go1 Edu variant has up to 3 nano processors, 5 super sensor systems, and 4 ultrasonic sensors. In contrast, Edu Plus is equipped with an Nvidia Jetson Xavier NX as standard. Model Comparison   Go1 Air Go1 Pro Go1 Edu Go1 Edu Plus SSS 1 Super-sensing system 1 set 5 sets 5 sets 5 sets Sensing calculation 1x (4x 1.43 GHz 128 Cores 0.5 T) 3x (4x 1.43 GHz 128 Cores 0.5 T) 3 Jetson Nano 2 Jetson Nano + 1 NVIDIA Jetson NX ISS 1 Intelligent Concomitant ✓ ✓ ✓ ✓ RTT 1 Pictures Transaction ✓ ✓ ✓ ✓ Charger 24 V, 4 V 24 V, 6 V 24 V, 6 V 24 V, 6 V Remote Control ✓ ✓ ✓ ✓ Load ≈3 kg ≈3 kg ≈5 kg (max ~10 kg) ≈5 kg (max ~10 kg) Heat Pipe Assisted Heat Dissipation ✓ ✓ ✓ ✓ Motion Speed 0~2.5 m/s 0~3.5 m/s 0~3.7 m/s (max ~5 m/s) 0~3.7 m/s (max ~5 m/s) Battery 1x 1x 1x 1x Graphical Programming Interface ✓ ✓ ✓ ✓ Scientific Programming Interface     ✓ ✓ Python Programming Interface     ✓ ✓ HAI 1 Human Sensing     ✓ ✓ APP Top View   ✓ ✓ ✓ 4G     ✓ ✓ Foot-end Physical Force Sensor     ✓ ✓ Multifunctional Peripheral Expansion Interface     ✓ ✓ Radar     2D or 3D optional 2D or 3D optional Included 1x Unitree Go1 1x Unitree Go1 Battery 1x Unitree Go1 Charger 1x Unitree Go1 Remote Controller Downloads User Manual GitHub

    € 12.539,00

    Leden identiek

  • Unitree Quadruped Go1 Pro

    Unitree Quadruped Go1 Pro

    Unitree Go1 series consists of quadruped robots for the research & development of autonomous systems in the fields of human-robot interaction (HRI), SLAM & transportation. Due to the four legs, as well as the 12DOF, this robot can handle a variety of different terrains. The Go1 comes with a perfected drive & power management system, which enables a speed (depending on the version) of up to 3.7 m/s or 11.88 km/h with an operating time of up to 2.5 hours. Furthermore, the motors have a torque of 23.70N.m at the body/thighs and 35.55N.m at the knees, which also allow jumps or backflips. Features High Dynamics 17 km/h Intelligent Side-Follow System (ISS) Super Sensory System (SSS) 10-view Detection AI Detection, Human Recognition, etc. Flexible and adaptive Joints Long Endurance Specifications Light and Compact Weight: 12 kg Size (folded): 0.588 x 0.29 x 0.22 m High Performance Max Speed: 4.7 m/s (17 kmh or 10.6 mph) Intelligent Side Follow System (Adopt Patented Wireless Vector Positioning and Control Technology) Robot dog can walk alongside its owner and not only follow The human-machine interaction is both harmonious and safe Super Sensory System Full View Coverage 5 Sets Fish-Eye Stereo Depth Cameras + AI Post-processing + 3 Sets of Hypersonic Sensors Lens Angle: 150 x 170° Built-in Powerful AI 16-core CPU + GPU (384 Cores, 1.5 TFLOPS) ISS and SSS Function Cooperatively Strong & Reliable Power System New Power Joint with Super Lightweight Low Noise and Long Life Heat Pipe Cooling System Built in the Knee Joint Motor Body/thigh joints: C1-8: 520 g 23.70N.m Knee Joint: C1-8 x 1.5 ratio 35.55N.m Unitree Go1 Variants The Go1 series has 3 variants (Go1 Air, Go1 Pro and Go1 Edu), which differ a little technically. The differences are mainly the processors and sensor systems, the Air and Pro variant works, depending on the model, with one or 3x (4x 1.43 GHz 128 Cores 0.5 T) processor as well as with 1 or 5 super sensor systems. Both variants are equipped with 3 ultrasonic sensors. The Go1 Edu variant has up to 3 nano processors, 5 super sensor systems, and 4 ultrasonic sensors. In contrast, Edu Plus is equipped with an Nvidia Jetson Xavier NX as standard. Model Comparison   Go1 Air Go1 Pro Go1 Edu Go1 Edu Plus SSS 1 Super-sensing system 1 set 5 sets 5 sets 5 sets Sensing calculation 1x (4x 1.43 GHz 128 Cores 0.5 T) 3x (4x 1.43 GHz 128 Cores 0.5 T) 3 Jetson Nano 2 Jetson Nano + 1 NVIDIA Jetson NX ISS 1 Intelligent Concomitant ✓ ✓ ✓ ✓ RTT 1 Pictures Transaction ✓ ✓ ✓ ✓ Charger 24 V, 4 V 24 V, 6 V 24 V, 6 V 24 V, 6 V Remote Control ✓ ✓ ✓ ✓ Load ≈3 kg ≈3 kg ≈5 kg (max ~10 kg) ≈5 kg (max ~10 kg) Heat Pipe Assisted Heat Dissipation ✓ ✓ ✓ ✓ Motion Speed 0~2.5 m/s 0~3.5 m/s 0~3.7 m/s (max ~5 m/s) 0~3.7 m/s (max ~5 m/s) Battery 1x 1x 1x 1x Graphical Programming Interface ✓ ✓ ✓ ✓ Scientific Programming Interface     ✓ ✓ Python Programming Interface     ✓ ✓ HAI 1 Human Sensing     ✓ ✓ APP Top View   ✓ ✓ ✓ 4G     ✓ ✓ Foot-end Physical Force Sensor     ✓ ✓ Multifunctional Peripheral Expansion Interface     ✓ ✓ Radar     2D or 3D optional 2D or 3D optional Included 1x Unitree Go1 1x Unitree Go1 Battery 1x Unitree Go1 Charger 1x Unitree Go1 Remote Controller Downloads User Manual GitHub

    € 6.249,00

    Leden identiek

  • Unitree Quadruped Go1 Air

    Unitree Quadruped Go1 Air

    De Unitree Go1 serie bestaat uit viervoetige robots voor research & development van autonome systemen op het gebied van mens-robot interactie (HRI), SLAM & transport. Door het hebben van vier poten en een 12-DOF houdingscontrole kan deze robot veel verschillende terreinen aan. De Go1 wordt geleverd met een geperfectioneerde aandrijving en power management systeem, wat een snelheid (afhankelijk van de uitvoering) tot 3,7 m/s of 11,88 km/u mogelijk maakt bij een bedrijfstijd van maximaal 2,5 uur. Verder hebben de motoren een koppel van 23,70 Nm op de body/dijen en 35,55 Nm op de knieën, waardoor ook sprongen of backflips mogelijk zijn. Kenmerken High Dynamics 17 km/u Intelligent Side-Follow System (ISS) Super Sensorisch System (SSS) 10-view Detectie AI-detectie, Human Recognition, enz. Flexibele en adaptieve gewrichten Langdurige werking Specificaties Licht en compact Gewicht: 12 kg Afmetingen (ingeklapt): 0,588 x 0,29 x 0,22 m High performance Max snelheid: 4,7 m/s (17 km/u of 10,6 mph) Intelligent Side Follow System (gepatenteerde Wireless Vector Positioning and Control Technology) De robothond kan naast zijn baasje lopen en niet alleen volgen De interactie tussen mens en machine is zowel harmonieus als veilig Super Sensory System Full View Coverage 5 sets fish-eye stereo dieptecamera's + AI-nabewerking + 3 sets hypersonische sensoren Lens openingshoek: 150 x 170° Ingebouwde krachtige AI 16-core CPU + GPU (384 cores, 1,5 TFLOPS) ISS en SSS werken coöperatief samen Robuust en betrouwbaar Power System Nieuwe superlichtgewicht Power Joint met laag geluidsniveau en een lange levensduur Heat Pipe koelsysteem ingebouwd in de motor van het knie gewricht Body/dijen gewrichten: C1-8: 520 g 23,70 N.m Knie gewricht: C1-8 x 1,5 ratio 35,55 N.m Unitree Go1 varianten De Go1 serie heeft 3 varianten (Go1 Air, Go1 Pro en Go1 Edu), die technisch enigszins verschillen. De verschillen betreffen vooral de processoren en de sensor systemen. De Air en Pro variant werken, afhankelijk van het model, met één of 3x (4x 1,43 GHz 128 Cores 0,5 T) processor en met 1 of 5 super sensor systems. Beide varianten zijn uitgerust met 3 ultrasone sensoren. De Go1 Edu-variant heeft tot 3 nano processors, 5 super sensor systems en 4 ultrasone sensoren. De Edu Plus daarentegen is standaard uitgerust met een Nvidia Jetson Xavier NX. Model vergelijking Go1 Air Go1 Pro Go1 Edu Go1 Edu Plus SSS 1 Super Sensing System 1 set 5 sets 5 sets 5 sets Sensing calculatie 1x (4x 1,43 GHz 128 cores 0.5 T) 3x (4x 1,43 GHz 128 cores 0.5 T) 3 Jetson Nano 2 Jetson Nano + 1 NVIDIA Jetson NX ISS 1 Intelligent Concomitant ✓ ✓ ✓ ✓ RTT 1 Pictures Transaction ✓ ✓ ✓ ✓ Oplader 24 V, 4 V 24 V, 6 V 24 V, 6 V 24 V, 6 V Afstandsbediening ✓ ✓ ✓ ✓ Draagvermogen ≈3 kg ≈3 kg ≈5 kg (max ~10 kg) ≈5 kg (max ~10 kg) Heat Pipe ondersteunde warmteafvoer ✓ ✓ ✓ ✓ Bewegingssnelheid 0 ~ 2,5 m/s 0 ~ 3,5 m/s 0 ~ 3,7 m/s (max ~5 m/s) 0 ~ 3,7 m/s (max ~5 m/s) Accu 1x 1x 1x 1x Grafische programming interface ✓ ✓ ✓ ✓ Scientific programming interface ✓ ✓ Python programming interface ✓ ✓ HAI 1 Human Sensing ✓ ✓ APP Top View ✓ ✓ ✓ 4G ✓ ✓ Voeteinde fysieke kracht sensor ✓ ✓ Multifunctionele uitbreidingsinterface voor randapparatuur ✓ ✓ Radar 2D of 3D optioneel 2D of 3D optioneel Inbegrepen 1x Unitree Go1 1x Unitree Go1 Accu 1x Unitree Go1 Oplader 1x Unitree Go1 Afstandsbediening Downloads Handleiding GitHub

    € 4.699,00

    Leden identiek

  • ROBOTIS TurtleBot3 Waffle Pi (incl. Raspberry Pi 4)

    ROBOTIS TurtleBot3 Waffle Pi (incl. Raspberry Pi 4)

    World’s Most Popular ROS PlatformTurtleBot is the most popular open source robot for education and research. The new generation TurtleBot3 is a small, low cost, fully programmable, ROS based mobile robot. It is intended to be used for education, research, hobby and product prototyping.Affordable CostTurtleBot was developed to meet the cost-conscious needs of schools, laboratories and companies. TurtleBot3 is the most affordable robot among the SLAM-able mobile robots equipped with a 360° Laser Distance Sensor LDS-01.ROS StandardThe TurtleBot brand is managed by Open Robotics, which develops and maintains ROS. Nowadays, ROS has become the go-to platform for all the roboticists around the world. TurtleBot can be integrated with existing ROS-based robot components, but TurtleBot3 can be an affordable platform for whom want to get started learning ROS.ExtensibilityTurtleBot3 encourages users to customize its mechanical structure with some alternative options: open source embedded board (as a control board), computer and sensors. TurtleBot3 Waffle Pi is a two-wheeled differential drive type platform but it is able to be structurally and mechanically customized in many ways: Cars, Bikes, Trailers and so on. Extend your ideas beyond imagination with various SBC, sensors and motors on a scalable structure.Modular Actuator for Mobile RobotTurtleBot3 is able to get a precise spatial data by using 2 DYNAMIXEL’s in the wheel joints. DYNAMIXEL XM series can be operated by one of 6 operating modes (XL series: 4 operating modes): Velocity control mode for wheels, Torque control mode or Position control mode for joint, etc. DYNAMIXEL can be used even to make a mobile manipulator which is light but can be precisely controlled with velocity, torque and position control. DYNAMIXEL is a core component that makes TurtleBot3 perfect. It is easy to assemble, maintain, replace and reconfigure.Open Control Board for ROSThe control board is open-sourced in hardware wise and in software wise for ROS communication. The open source control board OpenCR1.0 is powerful enough to control not only DYNAMIXEL’s but also ROBOTIS sensors that are frequently being used for basic recognition tasks in cost effective way. Various sensors such as Touch sensor, Infrared sensor, Color sensor and a handful more are available. The OpenCR1.0 has an IMU sensor inside the board so that it can enhance precise control for countless applications. The board has 3.3 V, 5 V, 12 V power supplies to reinforce the available computer device lineups.Open SourceThe hardware, firmware and software of TurtleBot3 are open source which means that users are welcomed to download, modify and share source codes. All components of TurtleBot3 are manufactured with injection molded plastic to achieve low cost, however, the 3D CAD data is also available for 3D printing.Specifications Maximum translational velocity 0.26 m/s Maximum rotational velocity 1.82 rad/s (104.27 deg/s) Maximum payload 30 kg Size (L x W x H) 281 x 306 x 141 mm Weight (+ SBC + Battery + Sensors) 1.8 kg Threshold of climbing 10 mm or lower Expected operating time 2h Expected charging time 2h 30m SBC (Single Board Computers) Raspberry Pi 4 (2 GB RAM) MCU 32-bit ARM Cortex-M7 with FPU (216 MHz, 462 DMIPS) Remote Controller RC-100B + BT-410 Set (Bluetooth 4, BLE) Actuator XL430-W210 LDS (Laser Distance Sensor) 360 Laser Distance Sensor LDS-01 or LDS-02 Camera Raspberry Pi Camera Module v2.1 IMU Gyroscope 3 AxisAccelerometer 3 Axis Power connectors 3.3 V/800 mA5 V/4 A12 V/1 A Expansion pins GPIO 18 pinsArduino 32 pin Peripheral 3x UART, 1x CAN, 1x SPI, 1x I²C, 5x ADC, 4x 5-pin OLLO DYNAMIXEL ports 3x RS485, 3x TTL Audio Several programmable beep sequences Programmable LEDs 4x User LED Status LEDs 1x Board status LED1x Arduino LED1x Power LED Buttons and Switches 2x Push buttons, 1x Reset button, 2x Dip switch Battery Lithium polymer 11.1 V 1800 mAh / 19.98 Wh 5C PC connection USB Firmware upgrade via USB / via JTAG Power adapter (SMPS) Input: 100-240 VAC 50/60 Hz, 1.5 A @maxOutput: 12 VDC, 5 A Downloads ROS Robot Programming GitHub E-Manual Community

    € 1.879,00

    Leden identiek

  • Clearpath Robotics TurtleBot 4 Lite

    Clearpath Robotics TurtleBot 4 Lite

    TurtleBot 4 is the next-generation of the world’s most popular open source robotics platform for education and research, offering better computing power, better sensors and a world class user experience at an affordable price point.TurtleBot 4 Lite is equipped with an iRobot Create 3 mobile base, a powerful Raspberry Pi 4 running ROS 2, OAK-D spatial AI stereo camera, 2D LiDAR and more. All components have been seamlessly integrated to deliver an out-of-the-box development and learning platform.Specifications Base platform iRobot Create 3 Wheels (Diameter) 72 mm Ground Clearance 4.5 mm On-board Computer Raspberry Pi 4 (4 GB) Maximum linear velocity 0.31 m/s in safe mode0.46 m/s without safe mode Maximum angular velocity 1.90 rad/s Maximum payload 9 kg Operation time 2h 30m – 4h depending on load Charging time 2h 30m Lidar RPLIDAR A1M8 Camera OAK-D-Lite User Power VBAT @1.9 A5 V @ Low current3.3 V @ Low current USB Expansion 2x USB 2.0 (Type A)2x USB 3.0 (Type A) Programmable LEDs Create 3 Lightring Buttons and Switches 2x Create 3 User buttons1x Create 3 Power Button Battery 26 Wh Lithium Ion (14.4 V nominal) Charging Dock Included Size (L x W x H) 342 x 339 x 192 mm Weight 3.3 kg DownloadsUser Manual

    € 1.599,00

    Leden identiek

There are a number of kits and books that will be your guide in gaining essential experience in electronics.

Login

Wachtwoord vergeten?

Heb je nog geen account?
Maak gratis een account aan en geniet van vele voordelen.