The AxiDraw's pen holder normally holds a pen (or other instrument) either vertically or at 45° from vertical. The Pen clip rotation stage is a lightweight adapter allows you to mount the instrument at arbitrary angles, and fine-tune that angle over a range of 90 degrees with a precision of 1 degree.This adapter is not normally needed in general writing and drawing usage. However certain precision applications of the AxiDraw – particularly those using the AxiDraw as a general purpose XY motion control stage – may find this to be helpful. Some users have also found it useful for fine-tuning the angle that a pen is mounted at when using italic or chisel-tip pens in combination with the Italic pen adapter.You can attach the rotation stage to the front face of the AxiDraw in two orientations, vertical or at 45° from vertical. These orientations, along with the 90°adjustment range, allow you to either adjust between vertical and horizontal, or between vertical and ±45° from vertical. Two small thumbscrews and an engraved bezel allow you to make adjustments and set the angle.Specifications
Material: Anodized 6061-T6 aluminum
Size: Outer radius 64 mm, height 48 mm, thickness 4.6 mm (excluding mounting hardware)
Weight: Approximately 11 g
Mounting hardware: included (2 each M3 flat head cap screws, M2 socket cap screws w/washers, 1.5 mm hex wrench)
CompatibilityThis adapter is compatible only with AxiDraw V3 family pen plotters that mount the pen on a 2-hole vertical slide. This includes all AxiDraw SE/A3, AxiDraw V3/A3 and AxiDraw V3 XLX units, and all AxiDraw V3 units manufactured after February 2017.
The Hello World circuit is the first circuit you print with your V-One. Have more than one person using your V-One? Then you might want more Hello World kits!The Hello World kit contains:
6x Green LEDs
3x 47k Resistors
3x 180R Resistors
3x 100k Resistors
3x 4.7UF Capacitor
1x 555 timer
1x 9V battery
The Punk Console circuit is an advanced tutorial to get you familiar with the V-One Drill attachment. Learn how to create a double sided board and turn the knobs to create music! The kit contains: 2x Green LEDs 8x 1k Resistors 3x 0.01uF Capacitor 2x 500K Trimpots 1x 556 Timer 1x Piezo Buzzer 1x 9 V Battery 1x 9 V Battery Connector Rivets and a V-One Drill are required.
Features
96% pre-installed 6-step fast assembly
Silent Motherboard, Decibel ?50 dB
Resumed Printing, Save Time and Filament
Take out the Model in an Easier Way
New UI Interaction with LCD Knob Screen
4.3-inch HD Color Screen
Specifications
Modeling technology
FDM (Fused Deposition Modeling?
Printer size
487 x 453 x 622 mm
Build size
220 x 220 x 270 mm
Supported filament
PLA/TPU/PETG/ABS
Printing layer thickness
0.05-0.35 mm
Printing speed
150 mm/s at the maximum
Printing precision
±0.1 mm
Nozzle diameter
0.4 mm
Number of nozzles
1
Filament diameter
1.75 mm
Machine net weight
9.1 kg
EXtruder gear ratio
1:3.5
Automatic bed leveling
CR touch
Printing platform
PC spring steel sheet
Screen
Knob color screen
Rated voltage
115/230 V | 50/60 Hz | 4.5/2.5 A
Printing method
Type-C USB /SD card
Supported file format
STL/OBJ/AMF
Supported software
Slicer/Cura/Repetier-Host/Simplify3D
Downloads
Quick Installation Guide
Firmware
Z-axis Limit Firmware
Excellent quality, high-torque 'NEMA 17' bipolar stepper motor for all of your motion control needs. Features a 5 mm precision ground shaft with a machined flat. Wiring harness included, various wire lengths available. Useful for all kinds of robotics projects! For example, this is the same stepper motor used in the EggBot kit and AxiDraw. Specifications Motor type: Bipolar stepper motor (4-wire) 1.8 degree step angle (200 steps per revolution) 5 mm output shaft, w/ machined flat 24 mm (0.95 inches) shaft length from screw face plate NEMA 17 form factor 31 mm (1.22 inches) mounting hole distance Mounting screw type: M3 with 3.5 mm min. thread depth 42 mm (1.65 inch) square body size Coil voltage 3.1 V Current 1 A per phase Winding resistance 3.1 ohms per phase Holding torque 1440 g*cm Leads are tinned, wrapped in heat shrink tubing (black or gray) Wire colors: Red and Yellow for the first coil, green and gray for the second coil. Downloads Datasheet
The Letter/A4 size Magnetic Easel is a sturdy work-holding tool that provides an alternative method of positioning paper or other workpieces for use with the AxiDraw. A heavy-duty alternative to the regular clip easel, it can be used with binder clips or the (included) positioning rulers and magnets. The base of the easel is a heavy-gauge sheet of magnetic steel. It has a powder-coat finish, lightly textured to help hold paper in place and light gray in color for visible contrast against most types of paper. Rubber bumpers on the bottom side (along with the weight of the steel) ensure a no-slip grip on your work table. To help index your paper in a consistent and reproducible position, the easel includes two six-inch (15 cm) rulers that you can rest your paper up against. The rulers are easy to remove and reversible, with inch and centimeter markings on the two sides. They can also be removed completely if you like, leaving just a flat sheet of steel (with a few ruler-mounting holes in it). This easel also includes six cylindrical magnets, 4 mm in diameter and 10 mm tall, that you can use to hold your paper down firmly. Their size and shape make them particularly easy to grasp and position (unlike, for example, disc magnets). Perhaps more importantly, they tend to yield and tip over if hit by an errant pen tip, rather than holding so fast as to damage your pen or move your paper. An optional set of paper holding clips can be added as well if you so choose. Overall dimensions: 12.875 × 9.580' (32.7 × 24.3 cm) Suitable for use with A4 and US letter paper sizes, envelopes, and smaller sizes of paper.
The set of magnets and spring clips is designed for use with the AxiDraw magnetic easel boards for letter/A4 and tabloid/A3 sizes, but can be used with almost any magnetic surface. The set includes a pair of special spring clips with magnetic bases, as well as six skinny magnets for holding down paper. The two special spring clips each have two curved tines that apply gentle pressure to your paper. They allow you to slide paper directly in and out, quickly and easily, without touching any magnets, clips, or tape. They have a long reach to be positioned behind the rulers on our magnetic easels. Magnetic bases allow you to position them where needed. Two of these spring clips provide just enough pressure to keep a sheet of paper steady while you write or draw on it. This set also includes six cylindrical magnets, 4 mm in diameter and 10 mm tall, which are easy to position and firmly hold paper. The tall aspect ratio makes them particularly easy to grasp (unlike disc magnets). Perhaps more importantly, they tend to yield and tip over if hit by an errant pen tip, rather than holding so fast as to damage your pen or move your paper.
The AxiDraw's pen holder normally holds the pen parallel to the front face of the vertical pen slide, either vertically or at 45° from vertical. This heavy-gauge aluminum adapter sits between the front face of the vertical slide and the pen clip, and serves to rotate the pen tip an additional 45°, not from vertical but out from parallel to the front face of the vertical slide. This gives the AxiDraw the ability to hold a pen in a 'right handed' grip, as opposed to the normal 'center-handed' (for lack of a better description) position. The right-handed grip makes it possible to hold the pen at a consistent angle suitable for use with regular pens, but also stub, italic, parallel, and chisel-point pens. Compatibility This adapter is compatible only with AxiDraw V3 family pen plotters that mount the pen on a 2-hole vertical slide. This includes all AxiDraw V3/A3 and AxiDraw V3 XLX units, and all AxiDraw V3 units manufactured after February 2017.
The V-One Drill includes everything you need to start making double sided boards right away: Drill Bit set (0.7 m, 0.8 mm, 0.9 mm, 1.0 mm, 1.6 mm) Sacrificial Layer (Black FR1) Copper Rivets (2 sizes, 200 pcs) Safety Glasses (clear) Rivet Tools (2 sizes) Hey Key Also included Power Supply (12 V, 25 W) Power Cable (1.8 m) Power Adapter Zip Ties (2 pcs) 4 Long Thumbscrews (10 mm) 2' x 3' FR1 Substrates (10 pcs) 3' x 4' FR1 Substrates (6 pcs) Zip Tie Mount
Need to dispense your own UV sensitive fluids (up to 550nm)?The pack includes:
4x 5cc UV-Blocking Syringe Barrels
4x Standard Fit Pistons (white)
4x High Viscosity Fit Pistons (red)
4x Tip Caps
4x End Caps
2x Female to Female Luer couplers
A set of high precision drill bits, covering the most common drill bit sizes. Just pop them in the V-One Drill with a 2.5 mm hex key (not included) and start drilling. The following sizes are included (2 of each): 0.70 mm 0.80 mm 0.90 mm 1.00 mm 1.60 mm
These boards are the maximum substrate size the V-One can handle. Just clamp them to the printing platform and press print to dispense the ink.
Pack of 6
Exact size is 4” x 5.3”
If you are going to be drilling, we recommend drilling on FR1 substrates. Unlike FR4, FR1 dust does not contain fiber glass. It is also a softer material, which means a less wear and tear on the drill bits. Download the template and incorporate them into your design here. 10 substrates included.
When you start to run out of space in your design, migrate over from the small substrates to these. These substrates are made of FR1 – which means they don't contain fibreglass. There is less wear on the drill bits. Download the template and incorporate them into your design here. 6 substrates included.
To protect the V-One from any damage during drilling, mount this piece of FR1 on the heated bed and clamp your substrate on top. The V-One Drill attachment will perforate your substrate but won't make it through this layer so your heated bed stays intact. Only one is included, but don't worry, the sacrifical layer can be reused plenty of times.
De Andonstar AD210 is een digitale microscoop met een groot 10,1-inch IPS-scherm, die een kijkhoek van 178° biedt, 1080P video ondersteunt en 12 MP foto’s kan vastleggen. Door de vergroting van 260x krijgt u met de microscoop een duidelijk beeld van de ligging van componenten op een printplaat. Met de microscoop wordt ook een 32 GB geheugenkaart en een afstandsbediening meegeleverd.
10,1-inch Super IPS digitale microscoop
Via een groot 10,1-inch IPS-scherm met een kijkhoek van 178°, en ondersteuning voor 1080P video en 12 MP foto-opnames, zorgt deze microscoop keer op keer voor heldere en gedetailleerde beelden.
Onderzoek munten als nooit tevoren
Ervaar de verbeterde beelden van de Andonstar AD210 muntmicroscoop. Met zijn verbeterde metalen standaard met een werkafstand van 10,2 inch kunt u zowel de algemene als de kleinste details van munten observeren, waaronder bijvoorbeeld die van zilveren dollars van 38,1 mm (1,5 inch).
Een onmisbare soldeermicroscoop voor de reparatie van elektronica
Probeer met de Andonstar AD210 soldeermicroscoop moeiteloos verschillende manieren uit voor het repareren met uw soldeerbout. Hij biedt op een duurzame manier meer ruimtelijk inzicht daarbij, waardoor het repareren van elektronica eenvoudiger wordt dan ooit.
Ontdek de wereld van de buitengewone vergrotingen
Ga op ontdekkingsreis met deze microscoop, die tevens is uitgerust met een set glaasjes voor biologische objecten en een glaasjeshouder met verlichting. Verken de verborgen schatten van de microkosmos en verbaast u over deze microscopische wereld.
De ultieme universele digitale microscoop
De indrukwekkende instelbare kijkafstand van 1 cm tot 26 cm en de uitgebreide set aan accessoires, waaronder een glaasjeshouder met verlichting voor het observeren van glaasjes met biologische objecten, maken de microscoop geschikt voor verschillende doeleinden, waaronder het repareren van elektronica, het verzamelen van munten en het observeren van glaasjes met biologische objecten. Het veelzijdige ontwerp zorgt ervoor dat hij aan al uw wensen voldoet.
Verbeterde supersterke standaard
We hebben de traditionele Andonstar standaard uitgebreid met een grotere voet en een maximale hoogte van maximaal 12,6 inch. Dit zorgt voor een directe verticale beweging en eenvoudige hoogteverstelling, waardoor de microscoop perfect is voor het observeren van munten, en voor het solderen.
Eenvoudige digitale microscoopcamera
Leg uw ontdekkingen moeiteloos vast en deel ze met anderen met behulp van de meegeleverde 32 GB geheugenkaart en kaartlezer. Maak foto's/video's en upload ze eenvoudig naar uw computer.
Specificaties
Schermgrootte
10,1 inch (25,7 cm)
Beeldsensor
2 MP
Video uitgang
FHD 1920x1080 (30 fps) 1080p 1440x1080 (30 fps) HD 1280x720 (30 fps)
Video formaat
AVI
Vergroting
Tot 260 keer
Foto resolutie
Max. 12 MP (4032x3024)
Foto formaat
JPG
Focus bereik
Min. 2 cm
Frame rate
Max. 30fps
Opslag
microSD kaart (tot 32 GB)
Voeding
5 V DC (via USB)
Verlichting
2 LED's op de voet
Grootte van de voet
18 x 20 x 32 cm
Inbegrepen
1x Andonstar AD210 digitale microscoop
1x Metalen voet met 2 LED's
1x Microscoop glaasjeshouder met verlichting
1x Standaard
2x Metalen clips
5x Microscoopschuif
1x Kaartlezer
1x 32 GB geheugenkaart
1x Afstandsbediening
1x USB voedingsadapter (EU)
1x USB voedingskabel
1x Poetsdoek
1x Handleiding
Downloads
Handleiding
Extra easel boards for AxiDraw V3/A3 can be used as replacements, or for staging additional workpieces for quickly swapping to the next plot. This set consists of one 11.75 x 17 inch (29.85 x 43.18 cm) hardboard platen with rubber feet attached, plus eight micro binder clips.
This rigid end effector plate is designed to be in place of the standard AxiDraw pen-lift Z stage, and provides an alternative mounting scheme for mounting various things to the end of the AxiDraw's arm, for applications where greater rigidity is important but the lifting ability of the standard Z stage is not required. The rigid end effector is custom machined from aluminum, and provides six M3 tapped holes and two M4 tapped holes for mounting what ever it is that you would like to mount to the end of the AxiDraw, to use it as a 2D robot arm. The hole pattern is compatible with the AxiDraw pen clip, so you can, if you like, mount the AxiDraw's pen clip to this end effector. Installation is straightforward, but requires a Pozidrive PZ2 screwdriver, not included*. Remove the AxiDraw's pen clip, and then remove the pen-lift Z stage by removing two screws with the PZ2 screwdriver. Install the rigid end effector plate in its place, using the two included mounting screws and the PZ2 screwdriver. You may wish to also tie back or fully remove the AxiDraw's cable guides, which normally extend to power the pen-lift stage. Specifications Material: Anodized 6061-T6 aluminum Size: 1.97 x 1.38 x 0.19 inches (50 x 35 x 4.8 mm) Weight: Approximately 11 g Mounting hardware: included (Two M4x12 pozidrive-head self-tapping screws) Compatibility All AxiDraw V3 family pen plotters AxiDraw V3/A3 AxiDraw SE/A3 AxiDraw MiniKit models
The tripod adapter is custom machined from a solid block of aluminum, and provides two standard tripod mounting points with 3/8-16 and light-duty 1/4-20 thread respectively. This allows you to mount the AxiDraw to a tripod, should you have reason to do so. We would highly recommend using a sturdy tripod with a 3/8-16 connection point and appropriate counterweight (sand bag, lifting weights, etc) to balance the weight of the AxiDraw while in use. Installation is straightforward, and does not require any tools other than those included with AxiDraw: Remove the existing foot pads from the AxiDraw (either standard or outrigger feet, depending on model) and attach this plate to the captured nuts in the bottom surface of the AxiDraw. For AxiDraw SE/A3 (April 2019 and newer), the tripod adapter attaches directly to tapped holes in the base of the machine. This heavy-duty tripod adapter is compatible with AxiDraw V3, AxiDraw V3/A3 and AxiDraw V3 XLX. It is also compatible with AxiDraw SE/A3 manufactured in April 2019 and newer. Specifications Material: Anodized 6061-T6 aluminum Size: 3.90 x 2.36 x 0.35 inches (99.1 x 60 x 8.3 mm) Weight: Approximately 144 g Mounting hardware: included (four M4x10 high-strength steel mounting screws)
This pair of extended 'outrigger' feet for AxiDraw V3 and AxiDraw V3 XLX consists of a pair of machined aluminum struts with large 1/2' diameter (12 mm) rubber foot pads set securely in recesses. It greatly increases the effective base area of the AxiDraw, making it much more stable when plotting, and capable of carrying heavier tools without worry of tipping over. In addition to providing a larger footprint, the outrigger feet also provide four mounting holes that make it easier to secure your AxiDraw to a surface, should you choose to do so. Each foot strut has two top-side accessible #8/M4 clearance holes. Installation is straightforward: Remove the two screws that hold the standard foot plates to the bottom of the AxiDraw, and attach these struts in their place with the included screws. Compatible with: AxiDraw V3 AxiDraw V3 XLX
Finer tolerance, higher speed
In the development of SV2, we focused on providing finer tolerance, higher speed and larger build area, including
8 mil (200 micron) traces
More than 2 layers
Finer glue dispensing with Single-part Epoxy
An Assembly System supporting 100+ parts as small as 0402, loaded in SMT strips
6" x 6" (150 x 150 mm) working area
Interact with SV2 through a web browser, uploading standard Gerber files, image files and centroid-and-rotation files to print and assemble your boards in minutes!
Inkjet Printing
New inkjet system, featuring more than 300 nozzles and a much smaller droplet size, allowing for thinner lines
Larger ink capacity for more boards per cartridge
Cleaning station to automatically maintain nozzles and extend cartridge life-span
Wider printhead, allowing for an increased sweep across the substrate and faster printing
Dispense Finer
Compatible with single-part epoxy
New motor, gearing and encoder allows for finer control in dispensing process
Micro-dispensing tips
Cleaning station for automated tip-wiping
BotFactory has a vision to revolutionize the electronics industry by bringing the factory to the desktop, creating a world where engineers, researchers and students can prototype printed electronics right there and then. BotFactory SV2 is their latest generation, capable of printing multilayer circuits, dispensing paste and pick-and-placing components within a small, 50 x 50 cm footprint.
BotFactory fabricates and assembles printed circuit boards in a way radically different from the familiar, stencil-andetch methods. The conductive traces are printed using a conductive, nanoparticle silver ink onto a substrate (FR-4 or even flexible Kapton®), and then a polymer ink is printed over the traces. Vias are printed using an additive process from the bottom to the top of the board. As CTO and Founder Carlos Ospina explains, “People always ask us ‘how can you create a multilayer circuit without drilling?!’, but at BotFactory we know that drilling is just one of many possible ways to connect a top layer to a bottom one”.
Each BotFactory SV2 comes with three heads to perform the printing, dispensing and assembly process. After printing the traces, the printing head is swapped out for the dispensing head and conductive glue deposited onto the pads. The final step is assembly where a pickand-place head equipped with a vacuum pump picks up parts from a tape-strip holder and use an upwards-facing camera to align the part and place it in the correct spot.
BotFactory took many lessons from their first product, Squink, and integrated them into SV2. The primary focus was on the printing technology, leveraging new inkjetting methods and curing techniques to print finer conductive traces, thinner insulating ink layers and overall speed. SV2 will be able to print more than two layers with an estimated trace width of 200 microns. Of course, with thinner lines comes finer dispensing, which required a major change to dispensing along with the conductive glues utilized; SV2 will now include a one-part epoxy instead of a two-part as with Squink. Pick-and-place supports 10 times more parts, along with tape-strip packaging and 0402-sized components, allowing users to explore small-batch production from within their workshop.
Of u nu op zoek bent naar soldeerpasta printers, reflow soldeersystemen, golfsoldeersystemen, selectieve soldeersystemen, SMT/BGA rework systemen, inspectiesystemen, soldeerstations, soldeergereedschappen, soldeer- en fluxen of know-how workshops en tutorials - Elektor kan altijd een passende oplossing bieden!
