Platformen

125 producten


  • Lo-Fi ESP32 based LoRa Wireless Communication Device (EU868)

    SB Components Lo-Fi ESP32 based LoRa Wireless Communication Device (EU868)

    Lo-Fi (ESP32 + LoRa combination) is the perfect solution for anyone looking to establish long-range wireless communication in a variety of applications with WiFi capabilities. LoRa offers exceptional range and easy connectivity, it allows you to seamlessly communicate with devices up to 5 km away. Devices provide an efficient and trustworthy choice for long-range wireless communication in addition to WiFi access to link internet clouds best suited for Internet of Things applications, enabling connectivity in remote and challenging settings. Features Device powered by powerful ESP32 S3 WROOM-1 which is having Xtensa dual-core 32-bit LX7 microprocessor, up to 240 MHz Inbuilt Wi-Fi & Bluetooth LE for wireless connectivity Type C interface for Programming/Power 1.14" TFT display for visual interactions GPIO breakouts for interfacing additional peripherals Breadboard compatible for easy DIY breadboarding projects 2 separate user programmable buttons along with Reset and Boot buttons 3.7 V Lithium Battery connector for a portable use case with an onboard charging option Use new generation LoRa spread spectrum to ensure stable communication For LoRa, faster speed and a longer data transmission range of up to 5 km Applications Internet of Things (IoT) Smart Home Automation Agricultural Automation Emergency Services Environmental Monitoring Industrial Automation Specifications Microcontroller: ESP32 S3 WROOM-1 Wireless Interface: WiFi, BLE, LoRa Protocol: 802.11b/g/n, Bluetooth 5.0 Memory Size: 16 MB Flash, 384 kB ROM, 8 MB SRAM Supply Voltage: 5 V Operating Voltage: 3.3 V Display Size: 1.14” Display Type: TFT Display resolution: 135 x 240 pixels Display driver: ST7789V Display Appearance: RGB Display color: 4k/65k/252k Display Luminance: 400 Cd/m² Operating Temperature: -20 to 70°C Storage Temperature: -30 to 80°C LoRa Module Specs: Carrier Frequency (License Free ISM): 868 MHz Chip: Based on SX1262 RF chip Range: 5Km Transmitting Power: 22 dBm Receiving Sensitivity: -147 dbm Data Rate: Up to 62.5 kbps Communication Port: UART serial Downloads Getting started guide Hardware design files Included 1x Lo-Fi Board 1x Antenna (868 MHz)

    € 49,95

    Leden € 44,96

  • ADS-B Antenna (1090 MHz)

    ADS-B Antenna (1090 MHz)

    This outdoor antenna made of fiberglass is optimized for the reception of ADS-B signals on the 1090 Mhz frequency. The antenna consists of a half-wave dipole with 5 dBi gain, encapsulated inside a fiberglass radome with an aluminum mounting base. With a Raspberry Pi, an RTL-SDR and this antenna, you can receive position data from aircraft in your area for apps such as Flightradar24 or FlightAware. Specifications Frequency 1090 MHz Antenna type Dipole 1/2 wave Connector N female Installation type Mast Diam 35-60 mm (mounting bracket included) Gain 5 dBi SWR ?1.5 Type of Polarization Vertical Maximum power 10 W Impedance 50 Ohms Dimensions 62.5 cm Tube diameter 26 mm Base antenna 32 mm Operating temperature -30°C to +60°C Included ADS-B antenna (1090 Mhz) Mast bracket (for installation on a 35 to 60 mm diameter mast)

    € 74,95

    Leden € 67,46

  • UFactory uArm Swift Pro

    UFactory UFactory uArm Swift Pro

    The uArm Swift Pro is a high quality robotic arm that can be used in a wide range of applications. The uArm Swift Pro was developed and optimized for use in education, which means that many packages are already available for open source platforms such as ROS. The uArm Swift Pro has a position repeatability of 0.2 mm and is also equipped with a stepper motor and a 12-bit encoder. These are just a few reasons that make the uArm Swift Pro an excellent choice for educational use. Another great feature is the 3D printing kit that converts the uArm Swift Pro into a 3D printer in less than 1 minute. The uArm supports the following development platforms/systems: UFACTORY SDK Arduino Python ROS GRABCAD OpenMV Smartphone App The smartphone app for iOS is already available in the App Store and enables easy control and monitoring of the robotic arm. The app for Android is in development and will be available soon. An example of the Machine Vision The following GIF shows the uArm in combination with the OpenMV Machine Vision Cam M7 and the facial recognition applications that can be implemented in MicroPython. Specifications Degrees of Freedom: 4 Repeatability: Up to 0.2 mm Payload: 500 g Working Range: 50-320 mm Positioning Speed: 100 m/s Position Feedback: 12-bit Encoder Dimensions: 150 x 140 x 281mm Weight: 2.2 kg Included UFactory uArm Swift Pro Body Bluetooth & Vacuum Gripper Downloads Datasheet

    € 939,00

    Leden identiek

  • Waveshare Jetson Nano Development Kit Lite

    Waveshare Waveshare Jetson Nano Development Kit Lite

    The Waveshare Jetson Nano Development Kit, based on AI computers Jetson Nano (with 16 GB eMMC) and Jetson Xavier NX, provides almost the same IOs, size, and thickness as the Jetson Nano Developer Kit (B01), more convenient for upgrading the core module. By utilizing the power of the core module, it is qualified for fields like image classification, object detection, segmentation, speech processing, etc., and can be used in sorts of AI projects. Specifications GPU 128-core Maxwell CPU Quad-core ARM A57 @ 1.43 GHz RAM 4 GB 64-bit LPDDR4 25.6 GB/s Storage 16 GB eMMC + 64 GB TF Card Video encoder 250 MP/s 1x 4K @ 30 (HEVC) 2x 1080p @ 60 (HEVC) 4x 1080p @ 30 (HEVC) Video decoder 500 MP/s 1x 4K @ 60 (HEVC) 2x 4K @ 30 (HEVC) 4x 1080p @ 60 (HEVC) 8x 1080p @ 30 (HEVC) Camera 1x MIPI CSI-2 D-PHY lanes Connectivity Gigabit Ethernet, M.2 Key E expansion connector Display HDMI USB 1x USB 3.2 Gen 1 Type A 2x USB 2.0 Type A 1x USB 2.0 Micro-B Interfaces GPIO, I²C, I²S, SPI, UART Dimensions 100 x 80 x 29 mm Included 1x JETSON-NANO-LITE-DEV-KIT (carrier + Nano + heatsink) 1x AC8265 dual-mode NIC 1x Cooling fan 1x USB cable (1.2 m) 1x Ethernet cable (1.5 m) 1x 5 V/3 A power adapter (EU) 1x 64 GB TF Card 1x Card reader Documentation Wiki

    € 269,00

    Leden € 242,10

  • Waveshare Jetson Orin Nano AI Development Kit

    Waveshare Waveshare Jetson Orin Nano AI Development Kit

    Nog 3 op voorraad

    This AI Edge Computing Development Kit is based on the Jetson Orin Nano Module providing rich peripheral interfaces such as M.2, DP, USB, etc. This kit also comes with a pre-installed AW-CB375NF wireless network card that supports Bluetooth 5.0 and dual-band WIFI, with two additional PCB antennas, for providing high-speed and reliable wireless network connection and Bluetooth communication. Specifications AI performance 40 TOPS GPU 1024-core N-VIDIA Ampere architecture GPU with 32 Tensor Cores GPU frequency 625 MHz (max) CPU 6-core Arm Cortex-A78AE v8.2 64-bit CPU, 1.5 MB L2 + 4 MB L3 CPU frequency 1.5 GHz (max) RAM 8 GB 128-bit LPDDR5, 68 GB/s Storage 128 GB NVMe Solid State Drive Power 7~15 W PCIE M.2 Key M slot with x4 PCIe Gen3 M.2 Key M slot with x2 PCIe Gen3 M.2 Key E slot USB USB Type-A: 4x USB 3.2 Gen2 USB Type-C (UFP) CSI camera 2x MIPI CSI-2 camera connector Video encode 1080p30 supported by 1-2 CPU cores Video decode 1x 4K60 (H.265) 2x 4K30 (H.265) 5x 1080p60 (H.265) 11x 1080p30 (H.265) Display 1x DisplayPort 1.2 (+MST) connector Interfaces 40-Pin Expansion Header (UART, SPI, I²S, I²C, GPIO), 12-pin button header, 4-pin fan header, DC power jack Networking 1x GbE connector Dimensions 103 x 90.5 x 34 mm Included Waveshare Orin Nano development kit 1x Jetson Orin Nano Module (8 GB) 1x JETSON-ORIN-IO-BASE 1x Cooling Fan 1x 128 GB NVMe Solid State Drive (assembled) 1x Wireless network card (assembled) 1x USB Type A to Type-C cable (1 m) 1x Ethernet cable (1.5 m) 1x Jumper 1x Power adapter (EU) Documentation Wiki

    Nog 3 op voorraad

    € 799,00

    Leden € 719,10

  • iCEBreaker FPGA Development Board

    iCEBreaker FPGA Development Board

    The iCEBreaker FPGA board is an open-source educational FPGA development board. The iCEBreaker is great for classes and workshops teaching the use of the open source FPGA design flow through Yosys, nextpnr, IceStorm, Icarus Verilog, Amaranth HDL and others. This means the board is low cost and has a nice set of features to allow for the design of interesting classes and workshop exercises. At the same time it allows the user to use the proprietary vendor tools if they choose to. After the workshop the boards can be easily used as a development board as most GPIO are exposed, broken out and configurable through jumpers on the back of the board. There is only a minimal amount of buttons and LED that can't be disconnected and used for your own purposes. Documentation Workshop

    € 89,95

    Leden € 80,96

  • USB-C to LoRa Dongle (EU868)

    SB Components USB-C to LoRa Dongle (EU868)

    USB-C to LoRa Dongle is a powerful and versatile LoRa device that lets you connect beyond boundaries. With its exceptional range and easy connectivity, it allows you to seamlessly communicate with devices up to 5 km away. LoRa Dongle is the perfect solution for anyone looking to establish long-range wireless communication in a variety of applications. This dongle provides direct USB interface control, eliminating the need for a deep understanding of LoRa transmission concepts. They seamlessly connect with devices like Raspberry Pi, SBCs, PCs, and laptops, simplifying the creation of IoT LoRa gateways. The USB LoRa Dongles function as transmitters and receivers, accommodating various message formats, including text, hexadecimal, and decimal. Features Device with the most recent LoRa module, offering up to a 5-kilometer data transmission range and higher speeds. Use new generation LoRa spread spectrum to ensure stable communication Type C interface for LoRa configuration/Power Status LED for power and data transmission Serial TX/RX pin breakout in Header and Screw terminal form Onboard jumper for operating mode selection Specifications Carrier Frequency (License Free ISM): 868 MHz Chip: Based on SX1262 RF chip Range: 5Km Transmitting Power: 22 dBm Receiving Sensitivity: -147 dbm Data Rate: Up to 62.5 kbps Interface: Type C Communication Port: UART serial Supply Voltage: 5 V Operating Voltage: 3.3 V Operating Temperature: -20 to 70°C Included 1x USB-C to LoRa Dongle 1x Antenna (868 MHz)

    € 24,95

    Leden € 22,46

  • Make your own Dasduino Solder Kit

    Make your own Dasduino Solder Kit

    If you’re looking for a simple way to start soldering or just want to make your own Dasduino, this soldering set is a great opportunity. "Make your own Dasduino CORE" is an educational set for learning the skill of soldering, with which you end up with a functional microcontroller board. As with the other SMD versions of the Dasduino CORE boards we offer, the possibilities are endless. It is based on the ATmega328P microcontroller, and all SMD components are already soldered on the board. The set also includes a THT socket for the microcontroller, which simplifies the replacement of the microcontroller should it ever become necessary. Included 1x PCB 7x Capacitors (100nF) 4x Capacitors (2.2uF) 2x Capacitors (22pF) 5x Resistors (2.2 kOhm) 5x Resistors (10 kOhm) 3x Resistors (1 kOhm) 1x Resistor (100 kOhm) 1x Resistor (100 ohm) 1x JST battery connector 1x LED (purple) 1x LED (white) 1x LED (blue) 1x LED (red) 1x LED (orange) 1x Socket for ATmega328P 1x ATmega328P microcontroller

    € 24,95

    Leden € 22,46

  • LED Dice Solder Kit

    Soldered LED Dice Solder Kit

    If you are looking for an easy way to get started with soldering or simply want to make a small portable gadget, this set is a great opportunity. "LED cube" is an educational set for learning the soldering skill, with which you get a small electronic game at the end. After you turn on and shake this board, certain leds will light up randomly and symbolize the number, as if a real die had been thrown. It is based on the Attiny404 microcontroller, programmed in Arduino, and there is a battery on the back which makes this gadget portable. There is also a keychain so you can always carry your new game with you! Soldering is easy according to the markings on the board. Included 1x PCB 1x ATtiny404 microcontroller 7x LEDs 7x Resistors (330 ohm) 1x Resistor (10 kohm) 1x Battery holder 1x CR2032 battery 1x Switch 1x Vibration sensor SW-18020P 1x Keychain ring

    € 9,95

    Leden € 8,96

  • Reaction Game Solder Kit

    Soldered Reaction Game Solder Kit

    If you are looking for a simple way to learn soldering, or just want to make a small gadget that you can carry, this set is a great opportunity. Reaction game is an educational kit which teaches you how to solder, and in the end, you get to have your own small game. The goal of the game is to press the button next to the LED as soon as it turns on. With every correct answer, the game gets a bit harder – the time you have to press the button shortens. How many correct answers can you get? It’s based on ATtiny404 microcontroller, programmed in Arduino. At its back, you’ll find CR2032 battery which makes the kit portable. There’s keychain holder as well. Soldering process is easy enough based on the mark on the PCB. Included 1x PCB 1x ATtiny404 microcontroller 4x LEDs 4x Pushbuttons 1x Switch 4x Resistors (330 ohm) 1x CR2032 battery holder 1x Battery CR2032 1x Keychain holder

    € 9,95

    Leden € 8,96

  • Stop Me Game Solder Kit

    Soldered Stop Me Game Solder Kit

    If you are looking for a simple way to learn soldering, or just want to make a small gadget that you can carry, this set is a great opportunity. Stop me game is an educational kit which teaches you how to solder, and in the end, you get to have your own small game. The LEDs go up and down, and your goal is to press the button as soon as the green LED turns on. With every correct answer, the game gets a bit harder – the time you have to press the button shortens. How many correct answers can you get? It’s based on ATtiny404 microcontroller, programmed in Arduino. At its back, you’ll find CR2032 battery which makes the kit portable. There’s keychain holder as well. Soldering process is easy enough based on the mark on the PCB. Included 1x PCB 1x ATtiny404 microcontroller 7x LEDs 1x Pushbutton 1x Switch 7x Resistors (330 ohm) 1x CR2032 battery holder 1x Battery CR2032 1x Keychain holder

    € 9,95

    Leden € 8,96

  • FLUX Beamo Laser Cutter

    FLUX FLUX Beamo Laser Cutter

    FLUX Beamo is a powerful and compact 30 W CO2 desktop laser cutter that can cut and engrave a range of materials including metals. With its easy-to-use design, intuitive controls and features, you can effortlessly create amazing things. Built-in HD camera Cutting and engraving is hassle-free with our preview mode. Place your material, preview the work area in the Beam Studio software and engrave. Your design comes out exactly as shown in the preview. Integrated safety features If left opened, auto pause ensures the laser stops. The internal water cooling system provides a stable cutting process. Plus, you can stop production with a single switch at any time. Powerful high resolution laser The Beamo ultra thin laser can engrave exceptional detail down to 0.05 mm wide with a clear resolution of 1,000 dpi. Fitting for any craft or small business project. The most precise compact CO2 laser engraver Beamo's sleek, modern and compact design fits beautifully in any home, school or workshop space. It comes pre-assembled with a metal body and acrylic lid, measuring 615 x 445 x 177 mm. Bring your designs to life with its 30 W CO2 laser operating on a 30 x 21 cm work area. Safe for home and school Beamo prioritises safety with its thoughtful design features. The machine is fully enclosed, and it automatically pauses if the lid is opened during a task. Additionally, there is a single switch for immediate machine shutdown in case of emergencies. Beamo is equipped with a Class 1 laser, which is completely safe under normal use. Specifications Dimensions 615 x 445 x 177 mm Weight 22 kg Work Area 300 x 210 x 45 mm (11.81 x 8,27 x 1.77") Camera Preview Area 300 x 195 mm Voltage AC 110 V / 220 V Touch Panel 1024 x 600 LCD Camera HD CMOS I/O Wi-Fi / Ethernet Laser Spec 30 W CO? Laser Laser Moving Speed 0~300 mm/s Laser Cutting Thickness 0-5 mm (varies by material) Software Mode Vector / Graphic (monochrome, gray scale) Operating System Windows / macOS / Linux Software File Type JPG / PNG / SVG / DXF Included FLUX Beamo (distilled water included) Vent hose Duct Clamp Double sided tape to align the mirror's Ethernet cable Vent Hose Double head wrench Wood piece Torx screwdriver and 2.5 mm hexagonal wrench Funnel 1x Laser Cutter Lubricant Power cord Wifi Dongle USB Beamo Manual Honey Comb Platform (30 W) Downloads Firmware

    € 2.660,00

    Leden identiek

  • FLUX Ador Laser Cutter (20 W)

    FLUX FLUX Ador Laser Cutter (20 W)

    FLUX Ador is the world's first color printing laser cutter. Powered by three high-quality, interchangeable modules, Ador enables you to engrave and cut though a wide range of materials while enhancing your projects with a pop of color. New creative potential with Ador Whether you’re an educator, small business, crafter or designer, with Ador, the application boundary is for you to define. Easy to use Place material then autofocus Drag and drop your design Engrave, cut or print Project Completed! Big workspace, big ideas Ador offers a big working space of 430 x 300 mm, with a depth of 30 mm, expanding the horizons of your creativity. Specifications Dimensions 637 x 488 x 226 mm Weight 19 kg Work Area X&Y: 20 W Diode laser: 430 x 300 mm (X & Y varies with different modules)Z: 30 mm (for all modules) & 20 mm (with prism) Camera Preview Area Whole work area Voltage AC 110-240 V Touch Panel Yes, 8 inches (diagonal) Camera 8 MP I/O USB / WiFi Laser Spec W Diode laser Module Laser Moving Speed 0~400 mm/s Laser Cutting Thickness Varies for different materials Software Mode Vector / Graphic (monochrome, gray scale) Operating System Windows / macOS / Linux Software File Type JPG / PNG / SVG / DXF Included FLUX Ador 20 W diode laser module 6x prism lift Power adapter Power cord Hex key Vent Hose Vent hose Duct Clamp Wooden test piece Laser Cutter Lubricant Downloads Firmware

    € 1.935,00

    Leden identiek

  • Makerfabs SenseLoRa Industrial-grade Air Monitor (EU868)

    Makerfabs Makerfabs SenseLoRa Industrial-grade Air Monitor (EU868)

    This air monitor is specifically used for monitoring greenhouses. It detects: Air temperature & Humidity CO2 concentration Light intensity Then transmit the data via LoRa P2P to the LoRa receiver (on your desk in the room) so that the user can monitor the field status or have it recorded for long-term analysis. This module monitors the greenhouse field status and sends all sensor data regularly via LoRa P2P in Jason format. This LoRa signal can be received by the Makerfabs LoRa receiver and thus displayed/recorded/analyzed on the PC. The monitoring name/data cycle can be set with a phone, so it can be easily implemented into the file. This air monitor is powered by an internal LiPo battery charged by a solar panel and can be used for at least 1 year with the default setting (cycle 1 hour). Features ESP32S3 module onboard with the WiFi and Bluetooth Ready to use: Power it on directly to use Module name/signal interval settable easily by phone IP68 water-proof Temperature: -40°C~80°C, ±0.3 Humidity: 0~100% moisture CO2: 0~1000 ppm Light intensity: 1-65535 lx Communication distance: Lora: >3 km 1000 mAh battery, charger IC onboard Solar panel 6 W, ensure system works Downloads Manual BH1750 Datasheet SGP30 Datasheet

    € 69,95

    Leden € 62,96

  • BeagleV-Fire SBC with RISC-V and FPGA

    BeagleBoard BeagleV-Fire SBC with RISC-V and FPGA

    BeagleV-Fire is a revolutionary single-board computer (SBC) powered by the Microchip’s PolarFire MPFS025T 5x core RISC-V System on Chip (SoC) with FPGA fabric. BeagleV-Fire opens up new horizons for developers, tinkerers, and the open-source community to explore the vast potential of RISC-V architecture and FPGA technology. It has the same P8 & P9 cape header pins as BeagleBone Black allowing you to stack your favorite BeagleBone cape on top to expand it’s capability. Built around the powerful and energy-efficient RISC-V instruction set architecture (ISA) along with its versatile FPGA fabric, BeagleV-Fire SBC offers unparalleled opportunities for developers, hobbyists, and researchers to explore and experiment with RISC-V technology. Chipset Features Microchip Polarfire MPFS025T SoC FPGA FPGA Fabric 23K logic elements (4-input LUT + DFF) 68 Math blocks (18x18 MACC) 4 SerDes lanes of 12.7 Gbps Microprocessor Subsystem Processor 1x 64-bit RV64IMAC monitor/boot core (E51) 4x 64-bit RV64GC Application cores (U54-MC) Fmax of 667 MHz (–40°C to 100°C Tj) 3.125 CoreMarks/MHz, 1.714 DMIPS/MHz Storage MMC 5.1 SD/SDIO 1 Quad SPI flash controller 128 KB eNVM 56 KB sNVM Memory Interfaces 36-bit DDR4/DDR3/LPDDR4/LPDDR3 memory controller with SECDED Communication Interfaces 2x GigE MACs, USB 2.0 OTG, 5x multi-mode UARTs, 2x SPI, 2x I²C, 2x CAN 2.0 Controllers. 2x PCIe Gen2 End Points/Root Ports Board Features On-board Memory 2 GB LPDDR4 16 GB Kingston eMMC 128 Mbit SPI flash Connectors and Expansion USB Type-C with high-Speed (480 Mbps) dual-role support and power input Gigabit Ethernet M.2 E-Key socket for WiFi and other PCIe/SDIO modules microSD card socket SYZYGY high-speed connector CSI 22-pin camera connector 2x46-pin BeagleBone Cape add-on headers with on-board ADC Screw terminal for 5 V power input 6-pin 3.3 V UART header JTAG TAG-CONNECT footprint Downloads Documentation

    € 199,95

    Leden € 179,96

  • Holybro QAV 250 ARF Drone Kit

    Holybro Holybro QAV 250 ARF Drone Kit

    The QAV250 Kit is the perfect way to get started developing on either PX4 or Ardupilot. It pairs a carbon fiber 250 racing frame and essential electronics with Pixhawk 6C mini autopilot. The kit is easy to assemble. No soldering needed. Specifications Micro Power Module (PM06 v2) Motors: 2207 KV1950 Wheelbase: 250 mm Dimensions: 198 x 235 x 70 mm Weight: 347 g Included Carbon fiber 250 airframe with hardware Micro Power Module (PM06 v2) Motors: 2207 KV1950 5" Plastic Props Fully assembled Power Management Board with ESCs (BLHeli S ESC 20A) Battery Straps Note: LiPo battery is not included.

    € 214,95

    Leden identiek

  • Holybro X500 V2 ARF Drone Kit

    Holybro Holybro X500 V2 ARF Drone Kit

    The X500 V2 ARF Kit is an affordable, lightweight, and robust carbon fiber professional drone kit that is easy to assemble (less than 15 minutes). It comes with the X500 V2 Frame Kit and motors, ESCs, power distribution boards and propellers preinstalled. It is perfectly compatible with various flight controllers such as the Holybro Pixhawk series, Durandal, Pix32 V5, etc. There are numerous improvements compared the previous model. Specifications Wheelbase: 500 mm Motor mount pattern: 16x16 mm Frame body: 144x144 mm, 2 mm thick Landing gear height: 215 mm Space between top and bottom plates: 28 mm Weight: 610 g Flight time: ~18 minutes hover with no additional payload. Tested with 5000 mAh battery. Payload: 1500 g (without battery, 70% throttle) Battery recommendation: 4S 3000-5000 mAh 20C+ with XT60 Lipo battery (not Included) Included X500 V2 Frame Kit With Preinstalled Items: 4x Motors: Holybro 2216 KV920 Motor (4 pcs) with XT30 Plug 4x ESCs (BLHeli S ESC 20A) 6x 1045 Propellers Power Distribution Board – XT60 plug for battery & XT30 plug for ESCs & peripherals Note: Depth camera mount is sold separately.

    € 379,95

    Leden identiek

  • UFactory 850 Robotic Arm

    UFactory UFactory 850 Robotic Arm

    UFactory 850 is the most powerful robot with industrial grade performance. Features 6DoF Payload: 5 kg Reach: 850 mm Repeatability: 0.02 mm Weight: 20 kg Applications Glambot Welding Screwdriving Robot Vision Industrial Production Designed for both mobile platforms and your workbench The AC control box contains an AC-DC adapter inside, 100-240 V AC is all ready to go. The DC control box supports 48-72 V wide inputs, it perfectly fits the battery system on your mobile platform. Flexible Deployment With Safe Feature Hand teaching, space-saving and easy to re-deploy to multiple applications without changing your production layout. Perfectly for recurrent tasks. Collision detection is available for all of our cobots. Your safety is always the top priority. Graphical Interface For Beginner-Friendly Programming Compatible with various operation systems, including macOS and Windows. Web-based technology compatible with all major browsers. Drag and drop to create your code in minutes. Powerful And Open Source SDK At Your Fingertips Fully functional open-source Python/C++ SDK provides more flexible programming. ROS/ROS2 packages are ready-to-go. Example codes help you to deploy the robotic arm smoothly. Specifications UFactory 850 xArm 5 xArm 6 xArm 7 Payload 5 kg 3 kg 5 kg 3.5 kg Reach 850 mm 700 mm 700 mm 700 mm Degrees of freedom 6 5 6 7 Repeatability ±0.02 mm ±0.1 mm ±0.1 mm ±0.1 mm Maximum Speed 1 m/s 1 m/s 1 m/s 1 m/s Weight (robot arm only) 20 kg 11.2 kg 12.2 kg 13.7 kg Maximum Speed 180°/s 180°/s 180°/s 180°/s Joint 1 ±360° ±360° ±360° ±360° Joint 2 -132°?132° -118°?120° -118°?120° -118°?120° Joint 3 -242°~3.5° -225°~11° -225°~11° ±360° Joint 4 ±360° -97°~180° ±360° -11°?225° Joint 5 -124°~124° ±360° -97°~180° ±360° Joint 6 ±360° ±360° -97°~180° Joint 7 ±360° Hardware Ambient Temperature Range 0-50°C Power Consumption Typical 240 W, max 1000 W Input Power Supply 48 V DC, 20.8 A Footprint Ø 190 mm Materials Aluminum, Carbon Fiber Base Connector Type M8x4 ISO Class Cleanroom 5 Robot Mounting Any End Effector Communication Protocol Modbus RTU End Effector I/O 2x DI / 2x DO / 2x AI / 1x RS485 Communication Mode Ethernet Included 1x UFactory 850 robotic arm 1x AC control box 1x Control box power cable

    € 11.779,00

    Leden identiek

  • UFactory xArm 7

    UFactory UFactory xArm 7

    This multi-axis robot perfectly balances power and size. Features 6 Axis Payload: 3.5 kg Reach: 700 mm Repeatability: 0.1 mm Max Speed 1000 mm/s Applications Machine Tending Bin Picking Mobile platform Lab Automation Robotic Research Durable Collaborative robots for your automation Industrial-grade harmonic drive and servomotors guarantee 24/7 working without stop. Crafted from Carbon fiber, 15 kg weight makes it possible for easier deployment. Flexible deployment with safe feature Hand teaching, lightweight, space-saving and easy to re-deploy to multiple applications without changing your production layout. Perfectly for recurrent tasks. Collision detection is available for all of our cobots. Your safety is always the top priority. Graphical interface for beginner-friendly programming Compatible with various of operation systems, including macOS and Windows. Web-based technology compatible with all major browsers. Drag and drop to create your code in minutes. Powerful and open source SDK at your fingertips Fully functional open-source Python/C++ SDK provides more flexible programming. ROS/ROS2 packages are ready-to-go. Example codes help you to deploy the robotic arm smoothly. Specifications UFactory 850 xArm 5 xArm 6 xArm 7 Payload 5 kg 3 kg 5 kg 3.5 kg Reach 850 mm 700 mm 700 mm 700 mm Degrees of freedom 6 5 6 7 Repeatability ±0.02 mm ±0.1 mm ±0.1 mm ±0.1 mm Maximum Speed 1 m/s 1 m/s 1 m/s 1 m/s Weight (robot arm only) 20 kg 11.2 kg 12.2 kg 13.7 kg Maximum Speed 180°/s 180°/s 180°/s 180°/s Joint 1 ±360° ±360° ±360° ±360° Joint 2 -132°?132° -118°?120° -118°?120° -118°?120° Joint 3 -242°~3.5° -225°~11° -225°~11° ±360° Joint 4 ±360° -97°~180° ±360° -11°?225° Joint 5 -124°~124° ±360° -97°~180° ±360° Joint 6 ±360° ±360° -97°~180° Joint 7 ±360° Hardware Ambient Temperature Range 0-50°C Power Consumption Min 8.4 W, Typical 200 W, max 400 W Input Power Supply 24 V DC, 16.5 A Footprint Ø 126 mm Materials Aluminum, Carbon Fiber Base Connector Type M5x5 ISO Class Cleanroom 5 Robot Mounting Any End Effector Communication Protocol Modbus RTU(rs485) End Effector I/O 2x DI/2x DO/2x AI/1x RS485 Communication Mode Ethernet Included 1x xArm 5 robotic arm 1x AC control box 1x Robotic arm power cable 1x Robotic arm end effector adapter cable 1x Robotic arm signal cable 1x Control box power cable 1x Network cable 1x Mounting tool 1x Quick start guide

    € 14.569,00

    Leden identiek

  • UFactory xArm 6

    UFactory UFactory xArm 6

    This multi-axis robot perfectly balances power and size. Features Payload: 5 kg Reach: 700 mm Repeatability: 0.1 mm Max Speed 1000 mm/s Applications Machine Tending Bin Picking Mobile platform Lab Automation Robotic Research Durable Collaborative robots for your automation Industrial-grade harmonic drive and servomotors guarantee 24/7 working without stop. Crafted from Carbon fiber, 15 kg weight makes it possible for easier deployment. Flexible deployment with safe feature Hand teaching, lightweight, space-saving and easy to re-deploy to multiple applications without changing your production layout. Perfectly for recurrent tasks. Collision detection is available for all of our cobots. Your safety is always the top priority. Graphical interface for beginner-friendly programming Compatible with various of operation systems, including macOS and Windows. Web-based technology compatible with all major browsers. Drag and drop to create your code in minutes. Powerful and open source SDK at your fingertips Fully functional open-source Python/C++ SDK provides more flexible programming. ROS/ROS2 packages are ready-to-go. Example codes help you to deploy the robotic arm smoothly. Specifications UFactory 850 xArm 5 xArm 6 xArm 7 Payload 5 kg 3 kg 5 kg 3.5 kg Reach 850 mm 700 mm 700 mm 700 mm Degrees of freedom 6 5 6 7 Repeatability ±0.02 mm ±0.1 mm ±0.1 mm ±0.1 mm Maximum Speed 1 m/s 1 m/s 1 m/s 1 m/s Weight (robot arm only) 20 kg 11.2 kg 12.2 kg 13.7 kg Maximum Speed 180°/s 180°/s 180°/s 180°/s Joint 1 ±360° ±360° ±360° ±360° Joint 2 -132°?132° -118°?120° -118°?120° -118°?120° Joint 3 -242°~3.5° -225°~11° -225°~11° ±360° Joint 4 ±360° -97°~180° ±360° -11°?225° Joint 5 -124°~124° ±360° -97°~180° ±360° Joint 6 ±360° ±360° -97°~180° Joint 7 ±360° Hardware xArm Robot specs Ambient Temperature Range 0-50°C Power Consumption Min 8.4 W, Typical 200 W, max 400 W Input Power Supply 24 V DC, 16.5 A Footprint Ø 126 mm Materials Aluminum, Carbon Fiber Base Connector Type M5x5 ISO Class Cleanroom 5 Robot Mounting Any End Effector Communication Protocol Modbus RTU(rs485) End Effector I/O 2x DI/2x DO/2x AI/1x RS485 Communication Mode Ethernet Included 1x xArm 5 robotic arm 1x AC control box 1x Robotic arm power cable 1x Robotic arm end effector adapter cable 1x Robotic arm signal cable 1x Control box power cable 1x Network cable 1x Mounting tool 1x Quick start guide

    € 11.259,00

    Leden identiek

  • UFactory xArm 5 Lite

    UFactory UFactory xArm 5 Lite

    This multi-axis robot perfectly balances power and size. Features 5 Axis Payload: 3 kg Reach: 700 mm Repeatability: 0.1 mm Max Speed 1000 mm/s Applications Machine Tending Bin Picking Mobile platform Lab Automation Robotic Research Durable Collaborative robots for your automation Industrial-grade harmonic drive and servomotors guarantee 24/7 working without stop. Crafted from Carbon fiber, 15 kg weight makes it possible for easier deployment. Flexible deployment with safe feature Hand teaching, lightweight, space-saving and easy to re-deploy to multiple applications without changing your production layout. Perfectly for recurrent tasks. Collision detection is available for all of our cobots. Your safety is always the top priority. Graphical interface for beginner-friendly programming Compatible with various of operation systems, including macOS and Windows. Web-based technology compatible with all major browsers. Drag and drop to create your code in minutes. Powerful and open source SDK at your fingertips Fully functional open-source Python/C++ SDK provides more flexible programming. ROS/ROS2 packages are ready-to-go. Example codes help you to deploy the robotic arm smoothly. Specifications UFactory 850 xArm 5 xArm 6 xArm 7 Payload 5 kg 3 kg 5 kg 3.5 kg Reach 850 mm 700 mm 700 mm 700 mm Degrees of freedom 6 5 6 7 Repeatability ±0.02 mm ±0.1 mm ±0.1 mm ±0.1 mm Maximum Speed 1 m/s 1 m/s 1 m/s 1 m/s Weight (robot arm only) 20 kg 11.2 kg 12.2 kg 13.7 kg Maximum Speed 180°/s 180°/s 180°/s 180°/s Joint 1 ±360° ±360° ±360° ±360° Joint 2 -132°?132° -118°?120° -118°?120° -118°?120° Joint 3 -242°~3.5° -225°~11° -225°~11° ±360° Joint 4 ±360° -97°~180° ±360° -11°?225° Joint 5 -124°~124° ±360° -97°~180° ±360° Joint 6 ±360° ±360° -97°~180° Joint 7 ±360° Hardware Ambient Temperature Range 0-50°C Power Consumption Min 8.4 W, Typical 200 W, max 400 W Input Power Supply 24 V DC, 16.5 A Footprint Ø 126 mm Materials Aluminum, Carbon Fiber Base Connector Type M5x5 ISO Class Cleanroom 5 Robot Mounting Any End Effector Communication Protocol Modbus RTU(rs485) End Effector I/O 2x DI/2x DO/2x AI/1x RS485 Communication Mode Ethernet Included 1x xArm 5 robotic arm 1x AC control box 1x Robotic arm power cable 1x Robotic arm end effector adapter cable 1x Robotic arm signal cable 1x Control box power cable 1x Network cable 1x Mounting tool 1x Quick start guide

    € 7.285,00

    Leden identiek

  • Oxocard Connect Innovator Kit

    Oxocard Oxocard Connect Innovator Kit

    With this comprehensive complete set, you can now enter the fascinating world of electronics. In addition to an Oxocard Connect and a breadboard cartridge, it contains 96 electronic components with which you can build a variety of electronic circuits. Features Free and unlimited access to the nanopy.io editor with a variety of scripts that you can transfer to your Oxocard Connect at the touch of a button. Electronics course with 15 experiments that show you step by step how to switch LEDs, connect a servo, generate acoustic signals with a piezo and much more. Oxocard Connect High quality microcontroller device with TFT screen, glass cover, joystick, USB-C, as well as revolutionary 16-pin cartridge slot. The Oxocard Connect represents the next generation of small experimental computers. The universal cartridge slot allows ready-made or self-developed boards to be brought to life instantly by simply plugging them in. Each card comes with drivers and demo programs installed and automatically loaded and started when plugged in. Breadboard Cartridge With the Breadboard you can quickly plug in your own circuits. A plug-in board with 17 rows is available for this purpose. Connections: two analog inputs, five digital ports, I²C, SPI, GND/V3.3. access to the 5 V power source of the port. Red LEDs are attached to the digital pins. 5 V can also be injected to power the Oxocard Connect without USB. Included 1x Oxocard Connect 1x Breadboard Cartridge Electronic components 1x PIR-Sensor (Motion detector) 1x Thermistor 10 k? (Temperature sensor) 1x Photoresistor 10 k? (Light sensor) 1x Potentiometer 1x Mikroservo SG92R 1x Piezo (Acoustic signals) 3x LED (green, yellow, red) 2x Buttons 9x Resistances 75x Cables (angled) – various colors and lengths

    € 89,95

    Leden € 80,96

  • Arduino Pro Portenta Vision Shield LoRa

    Arduino Arduino Pro Portenta Vision Shield LoRa

    De Portenta Vision Shield LoRa voegt industriële functies toe aan uw Portenta. Met deze hardware uitbreiding kunt u embedded computer vision toepassingen uitvoeren, draadloos via LoRa verbinding maken met de Arduino Cloud of met uw eigen infrastructuur, en uw systeem activeren bij het detecteren van geluiden.Deze uitbreidingskaart wordt geleverd met: een 320x320 pixels camerasensor: gebruik een van de cores in de Portenta om beeldherkenningsalgoritmen uit te voeren met behulp van de OpenMV voor Arduino editor draadloze lange afstand 868/915 MHz LoRa connectiviteit: verbind uw energiezuinige Portenta H7 met het Internet of Things twee ingebouwde microfoons voor directionele geluidsdetectie: leg geluid in realtime vast en analyseer dit JTAG-connector: voer low-level foutopsporing uit op uw Portenta board, of speciale firmware-updates met behulp van een externe programmer SD-card connector: sla uw vastgelegde data op de kaart op, of lees configuratiebestanden De Vision Shield LoRa is ontworpen om te werken met de Arduino Portenta H7. De Portenta boards zijn voorzien van multicore 32-bits ARM Cortex processors, die draaien op honderden megahertz, met megabytes aan programmageheugen en RAM. De Portenta boards worden geleverd met WiFi en Bluetooth.Specificaties Fototoestel Himax HM-01B0 camera module (site van de fabrikant) Resolutie 320 x 320 active pixel resolutie, met ondersteuning voor QVGA Beeldsensor High sensitivity 3.6? BrightSense pixeltechnologie Microfoon 2x MP34DT05 (datasheet) Connectiviteit 868/915MHz ABZ-093 LoRa Module met ARM Cortex-M0+ (datasheet) Dimensies 66 x 25 mm Gewicht 8 gr Downloads Datasheet Schematics

    € 84,95

    Leden € 76,46

  • Clearpath Robotics TurtleBot 4 Lite

    Clearpath Robotics TurtleBot 4 Lite

    TurtleBot 4 is the next-generation of the world’s most popular open source robotics platform for education and research, offering better computing power, better sensors and a world class user experience at an affordable price point.TurtleBot 4 Lite is equipped with an iRobot Create 3 mobile base, a powerful Raspberry Pi 4 running ROS 2, OAK-D spatial AI stereo camera, 2D LiDAR and more. All components have been seamlessly integrated to deliver an out-of-the-box development and learning platform.Specifications Base platform iRobot Create 3 Wheels (Diameter) 72 mm Ground Clearance 4.5 mm On-board Computer Raspberry Pi 4 (4 GB) Maximum linear velocity 0.31 m/s in safe mode0.46 m/s without safe mode Maximum angular velocity 1.90 rad/s Maximum payload 9 kg Operation time 2h 30m – 4h depending on load Charging time 2h 30m Lidar RPLIDAR A1M8 Camera OAK-D-Lite User Power VBAT @1.9 A5 V @ Low current3.3 V @ Low current USB Expansion 2x USB 2.0 (Type A)2x USB 3.0 (Type A) Programmable LEDs Create 3 Lightring Buttons and Switches 2x Create 3 User buttons1x Create 3 Power Button Battery 26 Wh Lithium Ion (14.4 V nominal) Charging Dock Included Size (L x W x H) 342 x 339 x 192 mm Weight 3.3 kg DownloadsUser Manual

    € 1.599,00

    Leden identiek

Deze categorie biedt een breed spectrum aan platformen waaruit u kunt kiezen. Ze hebben allemaal verschillende kenmerken en u kunt het platform kiezen dat het beste bij uw wensen of project past.

Login

Wachtwoord vergeten?

Heb je nog geen account?
Maak account aan