NIEUW

This is a simple DIY kit using Makerfabs' ESP32-S3 3.5" Parallel TFT with Touch (320x480) and Mabee MLX90640 module to monitor the temperature and display on the screen or save to SD card. It is a nice tool for circuit testing and non-contact temperature sensing. Features Based on ESP32-S3, 3.5-inch TFT with capacitive touch Auto check the highest temperature point Temperature accuracy: <1°C Suitable for applications such as human temperature checking or electronic boards debugging All hardware & software are open, users can modify & add more functions, such WiFi/Bluetooth data transmitting Downloads Default firmware New remote monitoring firmware Blog

Lees meer minder

This air monitor is specifically used for monitoring greenhouses. It detects: Air temperature & Humidity CO2 concentration Light intensity Then transmit the data via LoRa P2P to the LoRa receiver (on your desk in the room) so that the user can monitor the field status or have it recorded for long-term analysis. This module monitors the greenhouse field status and sends all sensor data regularly via LoRa P2P in Jason format. This LoRa signal can be received by the Makerfabs LoRa receiver and thus displayed/recorded/analyzed on the PC. The monitoring name/data cycle can be set with a phone, so it can be easily implemented into the file. This air monitor is powered by an internal LiPo battery charged by a solar panel and can be used for at least 1 year with the default setting (cycle 1 hour). Features ESP32S3 module onboard with the WiFi and Bluetooth Ready to use: Power it on directly to use Module name/signal interval settable easily by phone IP68 water-proof Temperature: -40°C~80°C, ±0.3 Humidity: 0~100% moisture CO2: 0~1000 ppm Light intensity: 1-65535 lx Communication distance: Lora: >3 km 1000 mAh battery, charger IC onboard Solar panel 6 W, ensure system works Downloads Manual BH1750 Datasheet SGP30 Datasheet

Lees meer minder

This ESP32 S3 7-inch IPS 5-point capacitive touch display with an ultra-high resolution of 1024 x 600 pixels is ideal for IoT applications. It is ideal for applications such as home automation. An integrated SD card enables recording/playback of stored data. There are also two Mabee/Grove connectors to connect various sensors to this board to create personal prototype projects in no time. Specifications Controller: ESP32-S3-WROOM-1, PCB antenna, 16 MB Flash, 8 MB PSRAM, ESP32-S3-WROOM-1-N16R8 Wireless: Wifi & Bluetooth 5.0 LCD: 7-inch High Lightness IPS FPS: >30 Resolution: 1024 x 600 LCD interface: RGB 565 Touch panel: Capacitive 5-point touch Touch panel driver: GT911 USB: Dual USB-C (one for USB-to-UART and one for native USB) UART to UART chip: CP2104 Power supply: USB-C 5.0 V (4.0 V~5.25 V) Button: Flash button and reset button Mabee interface: 1x I²C, 1x GPIO MicroSD: Yes Arduino support: Yes Type-C Power Delivery: Not supported Operation temperature: ?40 to +85°C Downloads Wiki GitHub ESP32-S3 Datasheet Screen touch coordinates calibration

Lees meer minder

The ESP32-S3 Parallel TFT not only offers more SRAM and ROM (compared to the S2 version), but with Bluetooth 5.0 it is also suitable for applications such as local monitoring and controlling.The built-in LCD driver ILI9488 uses 16-bit parallel lines to communicate with ESP32-S3, the main clock can be up to 20 MHz, which makes the display smooth enough for video displays. With this display, you can create more IoT display projects.Features Controller: ESP32-S3-WROOM-1, PCB Antenna, 16 MB Flash, 2 MB PSRAM, ESP32-S3-WROOM-1-N16R2 Wireless: Wifi & Bluetooth 5.0 LCD: 3.5-inch TFT LCD Resolution: 480x320 Color: RGB LCD Interface: 16-bit parallel LCD Driver: ILI9488 Touch Panel: Capacitive Touch Panel Driver: FT6236 USB: Dual USB Type-C (one for USB-to-UART and one for native USB) UART to UART Chip: CP2104 Power Supply: USB Type-C 5.0 V (4.0 V~5.25 V) Button: Flash button and reset button Mabee Interface: 1x I²C, 1x GPIO Backlight Controller: Yes MicroSD: Yes Arduino support: Yes Type-C Power Delivery: Not supported Operation temperature: -40? to +85? Dimension: 66 x 84.3 x 12 mm Weight: 52 g Downloads ESP32-S3 Datasheet GitHub Wiki LVGL Demo Code

Lees meer minder

This kit is based on ESP32 and LoRa. The ESP32 3.5' display is the console for the system, it receives the LoRa message from LoRa moisture sensors (support up to 8 sensors in the default firmware) , and send control commands to LoRa 4-channel MOSFET (2 4-channel MOSFET supported, with totally 8 channels), to control the connected valves open/close, and thus to control the irrigation for multiple points. Features Ready to use: Firmware are pre-programmed for all the modules before shipping, the user can only power them up and set the ID to the console, and start to use. Suitable for none-programmers, in 3 minutes to create filed application. With Lora wireless connection: The monitor & control range can be up to few kilometer, suitable for garden/small farm. Soil moisture sensor with good corrosion resistance, can be used at least half an year with 2 AAA battery. Easy to install: Compares to cheap solution with wires, which is hard to implement in files application, there the connection wires do not needed, the whole installation clean and easy; The valves can be connected Lora MOSFET easily. Hardware & Software Open: To study Lora & FreeRTOS. The ESP32 display console/Lora Soil Moisture Sensor/LoRa MOSFE are all programmed with Arduino. For programmers/engineers, can development further more specialized application. Based on ESP32, with WiFi connection, the console can also access to internet, the create much more applications including the moisture data updating to internet for remote monitor, and remote control with MQTT. Included 1x ESP32 3.5' Display (without camera) 1x Lora Expansion for ESP32 Display 2x Lora Moisture Sensor 1x Lora 4-channel MOSFET 1x 12 V Power Supply Water Pipe (5 m) 1x 1-input & 4-output Pipe Joint Downloads Instructable: Soil Monitoring & Irrigation with LoRa GitHub

Lees meer minder

Gebruik je Raspberry Pi met LTE Cat-4 4G/3G/2G communicatie & GNSS plaatsbepaling, voor data transmissie/telefoon/SMS op afstand, geschikt voor het op afstand bewaken/alarmeren. Deze 4G Hat is gebaseerd op de Maduino Zero 4G LTE, maar zonder controller. Hij moet werken met de Raspberry Pi (2x20 connector en USB). De Raspberry Pi communiceert met deze Hat met behulp van AT commando's (via de TX/RX pinnen in de 2X20 connector) voor eenvoudige besturingen, zoals SMS/Phone/GNSS; met de USB aansluiting en de juiste Linux driver geïnstalleerd, fungeert de 4G hat als een 4G netwerkadapter, die toegang heeft tot het Internet en gegevens kan verzenden met het 4G protocol. Vergeleken met een gewone USB 4G dongle heeft deze Raspberry Pi 4G Hat de volgende voordelen: Onboard audio codec, zodat je rechtstreeks met je RPi kunt bellen, of automatisch met een luidspreker kunt meeluisteren; Hardware UART communicatie, hardware besturing van de stroomvoorziening (door 2s puls van PI GPIO of POWERKEY toets), hardware besturing van de flight mode; Twee antennes voor LTE 4G en een voor GPS Kenmerken LTE Cat-4, met uplink snelheid van 50 Mbps en downlink snelheid 150 Mbps GNSS Positionering Audio Driver NAU8810 Ondersteuning voor dial-up, phone, SMS, TCP, UDP, DTMF, HTTP, FTP, etcetera Ondersteuning voor GPS, BeiDou, Glonass, LBS base station positionering SIM card slot, ondersteuning voor 1.8V/3V SIM card Onboard audio jack en audio decoder voor het maken van een telefoongesprek 2x LED indicatoren, om de bedrijfstatus eenvouding te volgen Supports SIM application toolkit: SAT Class 3, GSM 11.14 Release 99, USAT Inbegrepen 1x 4G LTE Hat voor Raspberry Pi 1x GPS antenne 2x 4G LTE antenne 2x Afstandbussen Downloads GitHub

Lees meer minder

Met het project uit deze kit stuur je de 6 servos van de robotarm aan met slechts zeer beperkt gebruik van MCU capaciteit, waardoor de Raspberry Pi Pico's MCU nog gemakkelijk andere taken aankan. Deze robotarm met 6 DOF* is een prima tool om robotica én Raspberry Pi Pico te leren programmeren en gebruiken. Leerzaam, maar vooral leuk! Inbegrepen in de kit zijn 5 MG996 (4 nodig in de assemblage en 1 als reserve) en 3 25-kg-servo's (2 nodig in de assemblage en 1 als reserve). Merk op dat voor de servo's de hoekschikking 0°~180° alle servo's vooraf moeten worden ingesteld op 90 graden vóór de assemblage om servoschade tijdens de beweging te voorkomen.Dit product bevat alle benodigde onderdelen om deze op Raspberry Pi Pico en MicroPython gebaseerde robotarm te maken.Het pakket bevat 1x Raspberry Pi Pico 1x Raspberry Pi Pico Servo Driver 1x De complete set '6 DOF Robot Arm' 1x 5 V/5 A Power Supply 2x Backup Servo (zie tekst) Downloads GitHub Wiki Assembly Guide Assembly Video *Een 'vrijheidsgraad' (DoF) met betrekking tot robotarmen is een onafhankelijk gewricht dat de arm vrij kan laten bewegen, hetzij in roterende, hetzij in translerende (lineaire) zin. Voor elke geometrische as waar een gewricht omheen kan draaien of zich langs kan uitstrekken, wordt dit geteld als één Degree of Freedom.

Lees meer minder

Inbegrepen 76x 10 mm 40 kHz transducers 1x Arduino Nano 1x L298N Dual Motor Drive Board 1x Voedingsschakelaar 1x DC-adapter 9 V 1x Jumper draden 6x zwarte en rode draad Enkele blootliggende draad 1x 3D-gedrukte TinyLev Documenten Instructables Wetenschappelijke informatie

Lees meer minder