NIEUW
LILYGO LILYGO T-Beam V1.2 ESP32 LoRa ontwikkelbord met 0,96" Display (EU868)
Dit LILYGO T-Beam V1.2 ESP32 LoRa ontwikkelbord wordt geleverd met een vooraf geïnstalleerd en gesoldeerd 0,96-inch scherm van Meshtastic. Het bord heeft een ingebouwde Semtech SX1262 LoRa-transceiver en is uitgerust met een NEO-6M GPS-ontvanger. GPS NEO-6M GPS-module: ondersteunt het GPS-protocol Onboard RTC kristal: ondersteuning voor interrupts en wakeup LoRa Long Range Low Power LoRa-transceiver Hoge gevoeligheid: -i48 dBm Transceiver snelheid: 300 kbps Versie: SX1276 (868 MHz) Firmware: Meshtastic Display OLED: 0,96-inch Driver: SSD1306 Specificaties Microcontroller ESP32 Flash 4 MB PSRAM 8 MB Serial chip CH9102 Protocol voor draadloos Wi-Fi + Bluetooth 4.2 PMU AXP2101 Functieknoppen 3 knoppen (Power + IO38 + Reset) Voeding Micro USB, 18650 accu Antenne 3D WiFi-antenne LoRa-antenne GPS keramische antenne Inbegrepen 1x LILYGO T-Beam V1.2 CH9102 1x 868 MHz antenne 1x Gesoldeerd 0,96" LCD (128x64) 2x Pin headers Downloads GitHub Schema
€ 49,95
Leden € 44,96
LILYGO LILYGO T-PicoC3 Development Board
T-PicoC3 is LILYGO's first motherboard with dual MCUs – equipped with Raspberry Pi RP2040 and ESP32-C3 chip (supporting WiFi and Bluetooth).Specifications MCU RP2040 Dual ARM Cortex-M0+ Flash 4 MB Programming language C/C++, MicroPython Support machine leraning library TensorFlow Lite Onboard functions Buttons: IO06+IO07, battery power detection 1.14 inch ST7789V IPS LCD Resolution 135 x 240 Display Full-color TFT Interface 4-Wire SPI Power supply 3.3 V Operating temperature -20~70°C Dimensions 2.4 x 5.3 cm (W x H) DownloadsGitHub
€ 17,95
Leden € 16,16
LILYGO LILYGO T-Display-S3 ESP32-S3 Development Board (with Headers)
LILYGO T-Display-S3 ESP32-S3 1,9-inch ST7789 LCD-scherm Development Board WiFi Bluetooth 5.0 draadloze module met 170x320 resolutie De T-Display-S3 is een ontwikkelbord met daarop als belangrijkste besturingschip de ESP32-S3. Hij is uitgerust met een 1,9-inch LCD-kleurenscherm en twee programmeerbare drukknoppen. Communicatie via de I8080-interface geschiedt met dezelfde lay-out als de T-Display. U kunt de ESP32S3 direct gebruiken voor USB-communicatie of programmeren. Specificaties MCU ESP32-S3R8 Dual-core LX7 microprocessor Draadloze communicatie Wi-Fi 802.11, BLE 5 + BT Mesh Programmeer platform Arduino IDE Micropython Flash 16 MB PSRAM 8 MB Detectie van batterijspanning IO04 Ingestelde functies Opstarten + resetten + IO14-knop LCD 1.9' diagonaal, TFT-kleurenscherm Drive chip ST7789V Resolutie 170(H)RGB x320(V) 8-Bit parallelle interface Werkspanning 3,3 V Ondersteuning STEMMA QT / Qwiic Connector JST-GH 1,25 mm 2-pins Downloads Pinout GitHub
LILYGO LILYGO TTGO T-Display RP2040 Development Board
LILYGO T-Display RP2040 Raspberry Pi Module 1.14-inch LCD Development Board This board is based on a Raspberry Pi Pico RP2040 with Dual Cortex-M0+ and 4 MB Flash memory. It is equipped with a 1.14-inch full color IPS display. The ST7789V display has a resolution of 135 x 240 pixels and is connected via the SPI interface. Specifications MCU RP2040 Dual ARM Cortex M0+ Flash 4 MB Bus interfaces 2x UART, 2x SPI, 2x I²C, 6x PWM Programming language C/C++, MicroPython Support machine learning library TensorFlow Lite Onboard functions Buttons: IO06+IO07, battery power detection TFT Display 1.14-inch ST7789V IPS LCD Resolution 135 x 240, full color Interface 4-Wire SPI interface Operating temperature -20°C ~ +70°C Working power supply 3.3 V Connector JST-GH 1.25 mm 2-pin Included LILYGO T-Display RP2040 Unsoldered headers JST cable Downloads Pinout GitHub
€ 19,95
Leden € 17,96
LILYGO LILYGO TTGO T-Display ESP32 Development Board (16 MB)
LILYGO T-Display ESP32 WiFi and Bluetooth Module Development Board 1.14-inch LCD Control BoardSpecifications Chipset Espressif-ESP32 240 MHz Xtensa single-/dual-core 32-bit LX6 microprocessor Flash QSPI flash 16 MB SRAM 520 kB SRAM Button Reset USB to TTL CP2104 Modular interface UART, SPI, SDIO, I²C, LED PWM, TV PWM, I²S, IRGPIO, ADC, capacitor touch sensor, DACLNA pre-amplifier Display IPS ST7789V 1.14 Inch Working voltage 2.7-4.2 V Working current About 67 MA Sleep current About 350 uA Working temperature range -40°C ~ +85°C Size & Weight 51.52 x 25.04 x 8.54 mm (7.81 g) Power Supply USB 5 V/1 A Charging current 500 mA Battery 3.7 V lithium battery JST Connector 2-Pin 1.25 mm USB Type-C WiFi Standard FCC/CE-RED/IC/TELEC/KCC/SRRC/NCC (ESP32 chip) Protocol 802.11 b/g/n (802.11n, speed up to 150 Mbps) A-MPDU and A-MSDU polymerization, support 0.4?S Protection interval Frequency range 2.4~2.5 GHz (2400~2483.5 M) Transmit Power 22 dBm Communication distance 300 m Bluetooth Protocol Meet bluetooth v4.2BR/EDR and BLE standard Radio frequency With -97 dBm sensitivity NZIF receiver Class-1, Class-2 & Class-3 emitter AFH Audio frequency CVSD&SBC audio frequency Software Wi-Fi Mode Station/SoftAP/SoftAP+Station/P2P Security mechanism WPA/WPA2/WPA2-Enterprise/WPS Encryption Type AES/RSA/ECC/SHA Firmware upgrade UART download/OTA (Through network/host to download and write firmware) Software Development Support cloud server development /SDK for user firmware development Networking protocol IPv4, IPv6, SSL, TCP/UDP/HTTP/FTP/MQTT User Configuration AT + Instruction set, cloud server, Android/iOS app OS FreeRTOS Included 1x T-Display (16 MB) 1x Charging Cable 2x Pin
€ 24,95
Leden € 22,46
