IoT & LoRa

49 producten

  • Dragino LSN50 Waterproof Long Range Wireless LoRa Sensor Node (EU868) - Elektor

    Dragino Dragino LSN50 Waterproof Long Range Wireless LoRa Sensor Node (EU868)

    The LSN50 wireless part is based on SX1276/SX1278 allows the user to send data and reach extremely long ranges at low data rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.The LSN50 MCU part uses STM32l0x chip from ST, STML0x is the ultra-low-power STM32L072xx microcontrollers incorporate the connectivity power of the universal serial bus (USB 2.0 crystal-less) with the high-performance ARM® Cortex®-M0+ 32-bit RISC core operating at a 32 MHz frequency, a memory protection unit (MPU), high-speed embedded memories (192 Kbytes of Flash program memory, 6 Kbytes of data EEPROM and 20 Kbytes of RAM) plus an extensive range of enhanced I/Os and peripherals.The LSN50 is an open-source product, it is based on the STM32Cube HAL drivers and lots of libraries can be found on the STM site for rapid development.Features STM32L072CZT6 MCU SX1276/78 LoRa Wireless Modem Pre-load with ISP bootloader I2C,LPUSART1,USB 18 x Digital I/Os 2 x 12bit ADC; 1 x 12bit DAC MCU wakes up by UART or Interrupt LoRa™ Modem Preamble detection Baud rate configurable LoRaWAN 1.0.2 Specification Software base on STM32Cube HAL drivers Open-source hardware / software IP66 Waterproof Enclosure Ultra-Low power consumption AT Commands to setup parameters 4000mAh Battery for Long term use Applications Wireless Alarm and Security Systems Home and Building Automation Automated Meter Reading Industrial Monitoring and Control Long-range Irrigation Systems LoRa Spec 168 dB maximum link budget. +20 dBm - 100 mW constant RF output vs. +14 dBm high-efficiency PA. Programmable bit rate up to 300 kbps. High sensitivity: down to -148 dBm. Bullet-proof front end: IIP3 = -12.5 dBm. Excellent blocking immunity. Low RX current of 10.3 mA, 200 nA register retention. Fully integrated synthesizer with a resolution of 61 Hz. FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation. Built-in bit synchronizer for clock recovery. Preamble detection. 127 dB Dynamic Range RSSI. Automatic RF Sense and CAD with ultra-fast AFC. Packet engine up to 256 bytes with CRC. Built-in temperature sensor and low battery indicator. MCU Spec MCU: STM32L072CZT6 Flash: 192KB SRAM: 20KB EEPROM: 6KB Clock Speed: 32Mhz Absolute Maximum Ratings VCC: 0.5 V ~ 3.9 V Operating Tempature: -40°C ~ 85°C I/O pins: 0.5 V ~ VCC+0.5 V Common DC Characteristics Supply Voltage: 1.8 V ~ 3.6 V Operating Tempature: -40°C ~ 85°C I/O pins: STM32L072CZT6 datasheet Power Consumption STOP Mode: 2.7 ?A @ 3.3 V RX Mode: 7.2 mA TX Mode: 125 mA@ 20 dbm Battery Li/SOCI2 unchargable battery Capacity: 4000 mAh Self Discharge: < 1% / Year @ 25°C Max continuously current: 130 mA Max boost current: 2 A, 1 second

    € 54,95

    Leden € 49,46

  • SparkFun DataLogger IoT (9DoF) - Elektor

    SparkFun SparkFun DataLogger IoT (9DoF)

    De SparkFun DataLogger IoT (9DoF) is een datalogger die al is voorgeprogrammeerd om automatisch IMU, GPS en verschillende druk-, vochtigheids- en afstandssensoren te loggen. Allemaal zonder ook maar één regel code te hoeven schrijven! De DataLogger detecteert, configureert en logt automatisch Qwiic sensoren. Hij is speciaal ontworpen voor gebruikers die alleen veel data dienen vast te leggen in een CSV- of JSON-bestand om dan verder te kunnen gaan met hun grotere project. Sla deze gegevens op op een microSD kaart, of stuur deze draadloos naar uw favoriete Internet of Things (IoT) service!Inbegrepen in elke DataLogger IoT is een IMU voor ingebouwde logging van een drie-assige accelerometer, gyro- en magnetometer. Waar de originele 9DOF Razor nog de oude MPU-9250 gebruikte maakt de DataLogger IoT gebruik van de ISM330DHCX van STMicroelectronics en de MMC5983MA van MEMSIC. Schakel gewoon de DataLogger IoT in, configureer het bordje om metingen van ondersteunde apparaten op te nemen en begin met loggen! Gegevens kunnen een timestamp krijgen indien time wordt gesynchroniseerd met NTP, GNSS of RTC.De DataLogger IoT is in hoge mate configureerbaar via een eenvoudig te gebruiken seriële interface. Sluit simpelweg een USB-C kabel aan en open een seriële terminal op 115200 baud. De logging-uitvoer wordt automatisch gestreamd naar zowel de terminal als naar de microSD kaart. Zodra u op een willekeurige toets in het terminalvenster drukt wordt het configuratiemenu geopend.De DataLogger IoT (9DoF) scant, detecteert, configureert en logt automatisch verschillende Qwiic sensoren die op het bordje zijn aangesloten (niets te solderen, niets te programmeren!).Specificaties ESP32-WROOM-32E module Geïntegreerde 802.11b/g/n WiFi 2.4 GHz transceiver Configureerbaar via CH340C Werkspanning 3,3 V tot 6,0 V (via VIN) 5 V met USB (via 5 V of USB type C) 3,6 V tot 4,2 V met LiPo accu (via BATT of 2-pins JST) Ingebouwde MCP73831 single cell LiPo lader Minimaal 500 mA laadsstroom 3,3 V (via 3V3) MAX17048 LiPo ladingsmeter Aansluitingen 1x USB-C 1x type JST connector voor LiPo accu 2x I²C met Qwiic ondersteuning 1x microSD kaartsleufje Ondersteuning voor 4-bits SDIO en microSD kaartjes geformatteerd met FAT32 9-assige IMU Accelerometer & Gyro (ISM330DHCX) Magnetometer (MMC5983MA) LED's Charge (CHG) Status (STAT) WS2812-2020 Addressable RGB Jumpers IMU interrupt Magnetometer interrupt RGB LED Status LED Laad LED I²C pull-up weerstanden USB Shield Knoppen Reset Boot Afmetingen: 4,2 x 5,1 cm (1,66 x 2,0 inch) Gewicht: 10,7 g Downloads Schema Eagle bestanden Afmetingen print Aansluitingen CH340 drivers Firmware GitHub hardware repo

    € 99,95

    Leden € 89,96

  • Makerfabs SenseLoRa Industrial - grade Air Monitor (EU868) - Elektor

    Makerfabs Makerfabs SenseLoRa Industrial-grade Air Monitor (EU868)

    This air monitor is specifically used for monitoring greenhouses. It detects: Air temperature & Humidity CO2 concentration Light intensity Then transmit the data via LoRa P2P to the LoRa receiver (on your desk in the room) so that the user can monitor the field status or have it recorded for long-term analysis. This module monitors the greenhouse field status and sends all sensor data regularly via LoRa P2P in Jason format. This LoRa signal can be received by the Makerfabs LoRa receiver and thus displayed/recorded/analyzed on the PC. The monitoring name/data cycle can be set with a phone, so it can be easily implemented into the file. This air monitor is powered by an internal LiPo battery charged by a solar panel and can be used for at least 1 year with the default setting (cycle 1 hour). Features ESP32S3 module onboard with the WiFi and Bluetooth Ready to use: Power it on directly to use Module name/signal interval settable easily by phone IP68 water-proof Temperature: -40°C~80°C, ±0.3 Humidity: 0~100% moisture CO2: 0~1000 ppm Light intensity: 1-65535 lx Communication distance: Lora: >3 km 1000 mAh battery, charger IC onboard Solar panel 6 W, ensure system works Downloads Manual BH1750 Datasheet SGP30 Datasheet

    € 69,95

    Leden € 62,96

  • Makerfabs LoRa Soil Monitoring & Irrigation Kit (EU868) - Elektor

    Makerfabs Makerfabs LoRa Soil Monitoring & Irrigation Kit (EU868)

    This kit is based on ESP32 and LoRa. The ESP32 3.5' display is the console for the system, it receives the LoRa message from LoRa moisture sensors (support up to 8 sensors in the default firmware) , and send control commands to LoRa 4-channel MOSFET (2 4-channel MOSFET supported, with totally 8 channels), to control the connected valves open/close, and thus to control the irrigation for multiple points. Features Ready to use: Firmware are pre-programmed for all the modules before shipping, the user can only power them up and set the ID to the console, and start to use. Suitable for none-programmers, in 3 minutes to create filed application. With Lora wireless connection: The monitor & control range can be up to few kilometer, suitable for garden/small farm. Soil moisture sensor with good corrosion resistance, can be used at least half an year with 2 AAA battery. Easy to install: Compares to cheap solution with wires, which is hard to implement in files application, there the connection wires do not needed, the whole installation clean and easy; The valves can be connected Lora MOSFET easily. Hardware & Software Open: To study Lora & FreeRTOS. The ESP32 display console/Lora Soil Moisture Sensor/LoRa MOSFE are all programmed with Arduino. For programmers/engineers, can development further more specialized application. Based on ESP32, with WiFi connection, the console can also access to internet, the create much more applications including the moisture data updating to internet for remote monitor, and remote control with MQTT. Included 1x ESP32 3.5' Display (without camera) 1x Lora Expansion for ESP32 Display 2x Lora Moisture Sensor 1x Lora 4-channel MOSFET 1x 12 V Power Supply Water Pipe (5 m) 1x 1-input & 4-output Pipe Joint Downloads Instructable: Soil Monitoring & Irrigation with LoRa GitHub

    € 149,95

    Leden € 134,96

  • LILYGO T - Deck ESP32 - S3 LoRa Development Board - Elektor

    LILYGO LILYGO T-Deck ESP32-S3 LoRa Development Board

    De T-Deck is een gadget in zakformaat met een 2,8" IPS LCD-scherm (320 x 240), een minitoetsenbord en een ESP32 dual-coreprocessor. Hoewel het niet echt een smartphone is, biedt het volop mogelijkheden voor technologieliefhebbers. Met wat programmeerkennis kun je het omzetten in een zelfstandig berichtenapparaat of een draagbaar codeerplatform. Specificaties Microcontroller ESP32-S3FN16R8 Dual-core LX7-microprocessor Draadloze connectiviteit 2,4 GHz Wi-Fi & Bluetooth 5 (LE) Ontwikkeling Arduino, PlatformlO, MicroPython Flash 16 MB PSRAM 8 MB Accu-ADC-pin IO04 Ingebouwde functies Trackball, microfoon, luidspreker Display 2,8" ST7789 SPI-interface IPS Resolutie 320 x 240 (volledige kijkhoek) Verzendvermogen +22 dBm SX1262 LoRa-zendontvanger (frequentie) 868 MHz Afmetingen 100 x 68 x 11 mm Inbegrepen 1x T-Deck ESP32-S3 LoRa 1x FPC-antenne (868 MHz) 1x Male pin (6-pins) 1x Voedingskabel Downloads GitHub

    € 84,95

    Leden € 76,46

  • Dragino LoRa/LoRaWAN IoT Kit v3 with 4G (EU868) - Elektor

    Dragino Dragino LoRa/LoRaWAN IoT Kit v3 met 4G (EU868)

    De Dragino LoRaWAN IoT Kit v3 is ontworpen om beginners en ontwikkelaars in staat te stellen snel LoRa/LoRaWAN en IoT technologie te leren en te demonstreren. Hij helpt gebruikers om een idee om te zetten in een praktische toepassing, en zo zelf het Internet of Things te realiseren. De LoRaWAN IoT Kit v3 kan worden gebruikt om de multi-channel LoRaWAN en de single-channel private LoRa oplossingen te evalueren. Gebruikers kunnen de LoRaWAN IoT Kit v3 ook gebruiken om verschillende configuraties netwerkstructuren te testen, en zo de beste voor hun IoT oplossing te vinden. De LoRaWAN IoT Kit v3 laat zien hoe je een LoRaWAN netwerk bouwt, en hoe je het netwerk kan gebruiken om gegevens van een LoRa sensor node naar de cloudserver te sturen. Afhankelijk van de feitelijke gebruiksomgeving kan de LoRaWAN gateway uw andere LoRa knooppunten tot zo’n 500 ~ 5000 meter verbinden. Kenmerken Open Source LoRa/LoRaWAN kits Ondersteuning van multi-channel LoRaWAN en single-channel LoRa Ondersteuning van verschillende netwerkstructuren Inbegrepen 1x LPS8v2 LoRaWAN gateway 1x LA66 LoRaWAN shield voor Arduino 1x LA66 USB LoRaWAN adapter voor pc/mobiel/RPi 1x DHT11 temperatuur en vochtigheidssensor 1x RGB LED 20x Dupont kabel (male to male) 20x Dupont kabel (female to female) 20x Dupont kabel (male to female) Downloads Datasheet Handleiding

    € 299,00

    Leden € 269,10

  • SparkFun Thing Plus Matter (MGM240P) - Elektor

    SparkFun SparkFun Thing Plus Matter (MGM240P)

    The SparkFun Thing Plus Matter is the first easily accessible board of its kind that combines Matter and SparkFun’s Qwiic ecosystem for agile development and prototyping of Matter-based IoT devices. The MGM240P wireless module from Silicon Labs provides secure connectivity for both 802.15.4 with Mesh communication (Thread) and Bluetooth Low Energy 5.3 protocols. The module comes ready for integration into Silicon Labs' Matter IoT protocol for home automation.What is Matter? Simply put, Matter allows for consistent operation between smart home devices and IoT platforms without an Internet connection, even from different providers. In doing so, Matter is able to communicate between major IoT ecosystems in order to create a single wireless protocol that is easy, reliable, and secure to use.The Thing Plus Matter (MGM240P) includes Qwiic and LiPo battery connectors, and multiple GPIO pins capable of complete multiplexing through software. The board also features the MCP73831 single-cell LiPo charger as well as the MAX17048 fuel gauge to charge and monitor a connected battery. Lastly, a µSD card slot for any external memory needs is integrated.The MGM240P wireless module is built around the EFR32MG24 Wireless SoC with a 32-bit ARM Cortext-M33 core processor running at 39 MHz with 1536 kb Flash memory and 256 kb RAM. The MGM240P works with common 802.15.4 wireless protocols (Matter, ZigBee, and OpenThread) as well as Bluetooth Low Energy 5.3. The MGM240P supports Silicon Labs' Secure Vault for Thread applications.Specifications MGM240P Wireless Module Built around the EFR32MG24 Wireless SoC 32-bit ARM-M33 Core Processor (@ 39 MHz) 1536 kB Flash Memory 256 kB RAM Supports Multiple 802.15.4 Wireless Protocols (ZigBee and OpenThread) Bluetooth Low Energy 5.3 Matter-ready Secure Vault Support Built-in Antenna Thing Plus Form-Factor (Feather-compatible): Dimensions: 5.8 x 2.3 cm (2.30 x 0.9') 2 Mounting Holes:4-40 screw compatible 21 GPIO PTH Breakouts All pins have complete multiplexing capability through software SPI, I²C and UART interfaces mapped by default to labeled pins 13 GPIO (6 labeled as Analog, 7 labeled for GPIO)All function as either GPIO or Analog Built-in-Digital to Analog Converter (DAC) USB-C Connector 2-Pin JST LiPo Battery Connector for a LiPo Battery (not included) 4-Pin JST Qwiic Connector MC73831 Single-Cell LiPo ChargerConfigurable charge rate (500 mA Default, 100 mA Alternate) MAX17048 Single-Cell LiPo Fuel Gauge µSD Card Slot Low Power Consumption (15 µA when MGM240P is in Low Power Mode) LEDs: PWR – Red Power LED CHG – Yellow battery charging status LED STAT – Blue status LED Reset Button: Physical push-button Reset signal can be tied to A0 to enable use as a peripheral device Downloads Schematic Eagle Files Board Dimensions Hookup Guide Datasheet (MGM240P) Fritzing Part Thing+ Comparison Guide Qwiic Info Page GitHub Hardware Repo

    € 34,95

    Leden € 31,46

  • iLabs Challenger RP2040 NFC - Elektor

    iLabs iLabs Challenger RP2040 NFC

    The Challenger RP2040 NFC is a small embedded computer, equipped with an advanced on-board NFC controller (NXP PN7150), in the popular Adafruit Feather form factor. It is based on an RP2040 microcontroller chip from the Raspberry Pi Foundation which is a dual-core Cortex-M0 that can run on a clock up to 133 MHz. NFC The PN7150 is a full featured NFC controller solution with integrated firmware and NCI interface designed for contactless communication at 13.56 MHz. It is fully compatible with NFC forum requirements and is greatly designed based on learnings from previous NXP NFC device generation. It is the ideal solution for rapidly integrating NFC technology in any application, especially small embedded systems reducing Bill of Material (BOM). The integrated design with full NFC forum compliancy gives the user all the following features: Embedded NFC firmware providing all NFC protocols as pre-integrated feature. Direct connection to the main host or microcontroller, by I²C-bus physical and NCI protocol. Ultra-low power consumption in polling loop mode. Highly efficient integrated power management unit (PMU) allowing direct supply from a battery. Specifications Microcontroller RP2040 from Raspberry Pi (133 MHz dual-core Cortex-M0) SPI One SPI channels configured I²C Two I²C channel configured (dedicated I²C for the PN7150) UART One UART channel configured Analog inputs 4 analog input channels NFC module PN7150 from NXP Flash memory 8 MB, 133 MHz SRAM memory 264 KB (divided into 6 banks) USB 2.0 controller Up to 12 MBit/s full speed (integrated USB 1.1 PHY) JST Battery connector 2.0 mm pitch On board LiPo charger 450 mA standard charge current Dimensions 51 x 23 x 3,2 mm Weight 9 g Note: Antenna is not included. Downloads Datasheet Quick start example

    € 22,95

    Leden € 20,66

  • Seeed Studio Grove 125 kHz RFID Reader - Elektor

    Seeed Studio Seeed Studio Grove 125 kHz RFID Reader

    Features Selectable output format: Uart or Wiegand. 4Pins Electronic Brick Interface High Sensitivity Specifications Dimensions: 44 mm x 24 mm x9.6 mm Weight: 15 g Battery: Exclude Voltage: 4.75 V - 5.25 V Working Frequency: 125 kHz Sensing Distance(Max): 70 mm TTL Output: 9600 baud rate, 8 data bits, 1 stop bit, and no verify bit Wiegand Output: 26 bits Wiegand format, 1 even verify bit, 24 data bits, and 1 odd verify bit

    € 17,95

    Leden € 16,16

  • Arduino Pro Nicla Vision - Elektor

    Arduino Arduino Pro Nicla Vision

    Heb je ooit een geautomatiseerd huis gewild? Of een slimme tuin? Met het Arduino IoT Cloud compatibel board Nicla Vision kun je je volgende smart project bouwen. Je kunt van overal ter wereld apparaten verbinden, gegevens bekijken, en je projecten besturen en delen.Nicla Vision combineert een krachtige STM32H747AII6 Dual ARM Cortex M7/M4 IC processor met een 2 MP kleurencamera die TinyML ondersteunt, evenals een slimme 6-assige bewegingssensor, geïntegreerde microfoon en een afstandssensor. Je kunt hem gemakkelijk in elk project inbouwen omdat hij ontworpen is om compatibel te zijn met alle Arduino Portenta en MKR producten, volledig integreert met OpenMV, MicroPython ondersteunt en ook zowel WiFi als Bluetooth Low Energy verbindingen biedt. Hij is zo compact - met zijn vormfactor van 22,86 x 22,86 mm - dat hij fysiek in de meeste scenario's past, en verbruikt zo weinig energie dat hij voor stand-alone toepassingen door een batterij gevoed kan worden. Dit alles maakt Nicla Vision tot de ideale oplossing om te ontwikkelen of prototypes te maken met on-device beeldverwerking en machine vision, voor het volgen van goederen, objectherkenning, voorspellend onderhoud en meer - gemakkelijker en sneller dan ooit. Train het om details te ontdekken, zodat je je kunt concentreren op belangrijke aspecten.Automatiseer om het even watControleer of elk product gelabeld is voor het de productielijn verlaat; ontgrendel deuren alleen voor bevoegd personeel, en alleen als ze de PBM correct dragen; gebruik AI om Nicla Vision te trainen om regelmatig analoge meters te controleren en upload de meetwaarden naar de Cloud; leer het om droogstaande gewassen te herkennen en de irrigatie aan te zetten als dat nodig is.Telkens als je moet handelen of een beslissing moet nemen afhankelijk van wat je ziet, laat je Nicla Vision voor je kijken, beslissen en handelen.Maak je zichtbaarCommuniceer met kiosken met eenvoudige gebaren, creëer overweldigende ervaringen, werk met cobots aan je zijde. Met Nicla Vision kunnen computers en slimme apparaten je zien, je herkennen, je bewegingen begrijpen en je leven gemakkelijker, veiliger, efficiënter en beter maken.Houd een oogje in het zeilLaat Nicla Vision dingen in de gaten houden: dieren opsporen aan de andere kant van de boerderij, je deurbel laten beantwoorden vanaf het strand, voortdurend controleren op trillingen of slijtage van je industriële machines. Het is je uitkijkpost die altijd aan staat en altijd nauwkeurig is, overal waar je hem nodig hebt.Downloads Schema's Datasheet

    € 149,95

    Leden € 134,96

  • Bijna uitverkocht Arduino Pro Portenta Machine Control - Elektor

    Arduino Arduino Pro Portenta Machine Control

    Nog 1 op voorraad

    De Portenta Machine Control is een volledig gecentraliseerde, energiezuinige, industriële control unit die apparatuur en machinerie kan aansturen. Hij kan worden geprogrammeerd met behulp van het Arduino-framework, of andere embedded ontwikkelingsplatforms.Dankzij zijn rekenkracht maakt de Portenta Machine Control het mogelijk om er een breed scala aan voorspellend onderhoud en AI projecten mee uit te voeren. Hij maakt het verzamelen van real-time gegevens uit de fabrieksomgeving mogelijk, en ondersteunt het op afstand bedienen van apparatuur, indien gewenst zelfs vanuit de cloud.Functies Kortere time-to-market Bestaande producten nieuw leven inblazen Connectiviteit toevoegen voor monitoring en control Aan uw behoefte aan te passen, elke I/O-pin kan worden geconfigureerd Maak apparatuur slimmer om klaar te zijn voor de AI revolutie Bied veiligheid en robuustheid vanuit het basisontwerp Geef kansen aan een nieuw businessmodel (bijv. servitization) Communiceer met uw apparatuur met geavanceerde HMI Modulair ontwerp voor aanpassing & upgrades De Portenta Machine Control ondersteunt bedrijven bij het creëren van nieuwe business-as-a-service modellen door het gebruik door klanten van apparatuur voor voorspellend onderhoud te monitoren, en waardevolle productiegegevens te bieden.De Portenta Machine Control maakt industriële soft-PLC besturing mogelijk, en kan worden aangesloten op een reeks externe sensoren en actuatoren via aparte digitale I/O, 4-20 mA compatibele analoge I/O, 3 configureerbare temperatuurkanalen, en een speciale I²C-connector. Er zijn meerdere opties beschikbaar voor netwerkconnectiviteit, waaronder USB, Ethernet en WiFi / Bluetooth Low Energy, en ook branchespecifieke protocollen zoals RS485. Alle I/O's worden beschermd door resetbare zekeringen, en het reeds ingebouwde power management is ontworpen om maximale betrouwbaarheid te garanderen bij gebruik in onbetrouwbare omgevingen.De Portenta Machine Control draait op een Portenta H7 microcontroller board (meegeleverd), een zeer betrouwbaar ontwerp dat kan werken binnen een industrieel temperatuurbereik (-40 °C tot +85 °C), met een dual-core architectuur die geen externe koeling nodig heeft. De hoofdprocessor biedt de optie om externe Human Machine Interfaces zoals displays, touchscreens, toetsenborden, joysticks en muizen aan te sluiten, om ter plaatse herconfiguratie van machines en aanpassing van processen mogelijk te maken.Het ontwerp van de Portenta Machine Control is geschikt voor een breed scala aan gebruiksopties. Zo is het mogelijk om via software een selectie van de I/O-poorten te configureren. De Portenta Machine Control onderscheidt zich doordat deze krachtige computer de productie eenduidig maakt en optimaliseert, waarbij één enkel type hardware aan al uw wensen kan voldoen. Opvallende kenmerken zijn bijvoorbeeld de volgende: Industriële performance die gebruikmaakt van de kracht van de Portenta boards DIN bar compatibele behuizing Push-in aansluitingen voor snelle connectie Compacte afmeting (170 x 90 x 50 mm) Betrouwbaar ontwerp dat kan werken binnen een industrieel temperatuurbereik (-40 °C tot +85 °C) met een dual-core architectuur die geen externe koeling vereist Embedded RTC (Real Time Clock) om een perfecte synchronisatie van de processen te garanderen Maak gebruik van de ingebouwde connectiviteitsopties zonder externe onderdelen De Portenta Machine Control kan worden gebruikt in meerdere sectoren van de industrie, bij een breed scala aan machinetypes, waaronder: etiketteermachines, form- en sealmachines , kartonneermachines, lijmmachines, elektrische ovens, industriële wasmachines en drogers, mixers, enz.Voeg de Portenta Machine Control moeiteloos toe aan uw bestaande productieprocessen en word eigenaar van uw eigen oplossingen in de markt van machinerie.Specificaties Processor STM32H747XI Dual Cortex-M7 + M4 32-bit low power Arm MCU (Portenta H7) Input • 8 digitale 24 VDC• 2 kanalen encoder readings• 3 analoog voor PT100/J/K temperatuur probes (3-draads kabel met compensatie)• 3 analoge ingangen (4-20 mA/ 0-10 V/NTC 10K) Output • 8 digitale 24 VDC tot 0,5 A (kortsluitbeveiliging)• 4 analoge 0-10 V (tot 20 mA output per kanaal) Andere I/O 12 programmeerbare digitale I/O (24 V logic) Communicatieprotocollen • CAN-BUS• Programmeerbare seriële poort 232/422/485 Connectiviteit • Ethernet• USB Programming Port• WiFi• Bluetooth Low Energy Geheugen • 16 MB onboard Flash memory• 8 MB SD-RAM Dimensies 170 x 90 x 50 mm Gewicht 186 gr Voeding 24 VDC +/- 20% Type connector Push-in aansluitingen voor snelle connectie Bedrijfstemperatuur -40 °C to +85 °C (-40 °F tot 185 °F) Downloads Datasheet Schema Pinout

    Nog 1 op voorraad

    € 359,00

    Leden € 323,10

  • CubeCell HTCC - AB01 (V2) LoRa Development Board (EU868) - Elektor

    Heltec Automation CubeCell HTCC-AB01 (V2) LoRa Development Board (EU868)

    Niet op voorraad

    The CubeCell series is designed primarily for LoRa/LoRaWAN node applications. Built on the ASR605x platform (ASR6501, ASR6502), these chips integrate the PSoC 4000 series MCU (ARM Cortex-M0+ Core) with the SX1262 module. The CubeCell series offers seamless Arduino compatibility, stable LoRaWAN protocol operation, and straightforward connectivity with lithium batteries and solar panels. The HTCC-AB01 (V2) is an upgraded version of the HTCC-AB01 board. Features Arduino compatible Based on ASR605x (ASR6501, ASR6502), those chips are already integrated the PSoC 4000 series MCU (ARM Cortex-M0+ Core) and SX1262 LoRaWAN 1.0.2 support Ultra low power design, 3.5 uA in deep sleep Onboard SH1.25-2 battery interface, integrated lithium battery management system (charge and discharge management, overcharge protection, battery power detection, USB/battery power automatic switching) Good impendence matching and long communication distance. Onboard solar energy management system, can directly connect with a 5.5~7 V solar panel Micro USB interface with complete ESD protection, short circuit protection, RF shielding, and other protection measures Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing Specifications Main Chip ASR6502 (48 MHz ARM Cortex-M0+ MCU) LoRa Chipset SX1262 Frequency 863~870 MHz Max. TX Power 21 ±1 dBm Max. Receiving Sensitivity −134 dBm Hardware Resource 1x UART1x SPI1x I²C1x SWD1x 12-bit ADC input8-channel DMA engine8x GPIO2x PWM Memory 128 Kb FLASH16 Kb SRAM Power consumption Deep Sleep 3.5 uA Interfaces 1x USB-C1x LoRa Antenna (IPEX 1.0)SH1.25; 11x 2x 2.54 Pin header1x (2x 2.54 Pin header) Solar Energy VS pin can be connected to 5.5~7 V solar panel Battery 3.7 V Lithium battery (power supply and charging) Operating temperature −20~70°C Dimensions 40.6 x 22.9 x 7.6 mm Included 1x CubeCell HTCC-AB01 (V2) Development Board 1x Antenna 1x 2x SH1.25 battery connector Downloads Datasheet Schematic Quick start GitHub

    Niet op voorraad

    € 19,95

    Leden € 17,96

  • Heltec HT - M00 Dual - Channel LoRa Gateway (EU868) - Elektor

    Heltec Automation Heltec HT-M00 2-kanaals LoRa Gateway (EU868)

    De HT-M00 is een tweekanaals gateway die speciaal is ontworpen voor LoRa-toepassingen voor slimme gezinnen die werken met minder dan 30 LoRa-nodes. De gateway is gebouwd rond twee SX1276-chips die worden aangestuurd door ESP32. Om monitoring van de 125 kHz SF7~SF12-spreidingsfactor mogelijk te maken, is een softwaremixer ontwikkeld, die gewoonlijk een basisbandsimulatieprogramma wordt genoemd. De softwaremixer is een cruciaal onderdeel waardoor de HT-M00-gateway met hoge efficiëntie kan werken. Het is ontworpen om basisbandsignalen te simuleren, die vervolgens worden gemengd met de radiofrequentiesignalen om de gewenste uitvoer te produceren. De softwaremixer is met grote zorg en precisie ontwikkeld en heeft strenge tests ondergaan om ervoor te zorgen dat hij nauwkeurige en betrouwbare resultaten kan leveren. Kenmerken ESP32 + SX1276 Emuleert LoRa-demodulatoren Automatische adaptieve spreadspectrumfactor, SF7 tot SF12 voor elk kanaal is optioneel Maximale output: 18 ±1dBm Ondersteuning voor LoRaWAN klasse A, klasse C-protocol Specificaties MCU ESP32-D0WDQ6 LoRa-chipset SX1276 LoRa-band 863~870 MHz Voedingsspanning 5 V Ontvangstgevoeligheid -110 dBm bij 300 bps Interface USB-C Max. TX-vermogen 17dB ±1dB Bedrijfstemperatuur −20~70°C Afmetingen 30 x 76 x 14 mm Inbegrepen 1x HT-M00 2-kanaals LoRa Gateway 1x Muurbeugel 1x USB-C-kabel Downloads Manual Software Documentation

    € 74,95

    Leden € 67,46

  • Arduino MKR IoT Carrier - Elektor

    Arduino Arduino MKR IoT Carrier

    Gegevensvastlegging: Breng de omgeving rond de drager in kaart met behulp van de geïntegreerde temperatuur-, vochtigheids- en druksensoren en verzamel gegevens over bewegingen met behulp van de 6-assige IMU en licht-, gebaar- en nabijheidssensoren. Voeg eenvoudig meer externe sensoren toe om meer gegevens van meer bronnen vast te leggen via de Grove-connectoren op de drager (x3). Gegevensopslag: Leg alle gegevens vast en sla ze lokaal op een SD-kaart op, of maak verbinding met de Arduino IoT Cloud voor real-time gegevensvastlegging, opslag en visualisatie. Data Visualisatie: Bekijk lokaal de real-time sensorwaarden op het ingebouwde OLED-kleurendisplay en creëer visuele of geluidssignalen met behulp van de ingebouwde LED's en zoemer. Totale bediening:Directe bediening van elektronische apparaten met kleine spanning met behulp van de ingebouwde relais en de vijf tactiele knoppen, waarbij het geïntegreerde display een handige on-device interface biedt voor directe bediening.

    € 59,95

    Leden € 53,96

  • Lo - Fi - ESP32 based LoRa Wireless Communication Device (EU868) - Elektor

    SB Components Lo-Fi ESP32 based LoRa Wireless Communication Device (EU868)

    Lo-Fi (ESP32 + LoRa combination) is the perfect solution for anyone looking to establish long-range wireless communication in a variety of applications with WiFi capabilities. LoRa offers exceptional range and easy connectivity, it allows you to seamlessly communicate with devices up to 5 km away. Devices provide an efficient and trustworthy choice for long-range wireless communication in addition to WiFi access to link internet clouds best suited for Internet of Things applications, enabling connectivity in remote and challenging settings. Features Device powered by powerful ESP32 S3 WROOM-1 which is having Xtensa dual-core 32-bit LX7 microprocessor, up to 240 MHz Inbuilt Wi-Fi & Bluetooth LE for wireless connectivity Type C interface for Programming/Power 1.14" TFT display for visual interactions GPIO breakouts for interfacing additional peripherals Breadboard compatible for easy DIY breadboarding projects 2 separate user programmable buttons along with Reset and Boot buttons 3.7 V Lithium Battery connector for a portable use case with an onboard charging option Use new generation LoRa spread spectrum to ensure stable communication For LoRa, faster speed and a longer data transmission range of up to 5 km Applications Internet of Things (IoT) Smart Home Automation Agricultural Automation Emergency Services Environmental Monitoring Industrial Automation Specifications Microcontroller: ESP32 S3 WROOM-1 Wireless Interface: WiFi, BLE, LoRa Protocol: 802.11b/g/n, Bluetooth 5.0 Memory Size: 16 MB Flash, 384 kB ROM, 8 MB SRAM Supply Voltage: 5 V Operating Voltage: 3.3 V Display Size: 1.14” Display Type: TFT Display resolution: 135 x 240 pixels Display driver: ST7789V Display Appearance: RGB Display color: 4k/65k/252k Display Luminance: 400 Cd/m² Operating Temperature: -20 to 70°C Storage Temperature: -30 to 80°C LoRa Module Specs: Carrier Frequency (License Free ISM): 868 MHz Chip: Based on SX1262 RF chip Range: 5Km Transmitting Power: 22 dBm Receiving Sensitivity: -147 dbm Data Rate: Up to 62.5 kbps Communication Port: UART serial Downloads Getting started guide Hardware design files Included 1x Lo-Fi Board 1x Antenna (868 MHz)

    € 49,95

    Leden € 44,96

  • Arduino MKR WAN 1310 - Elektor

    Arduino Arduino MKR WAN 1310

    Altijd al een geautomatiseerd huis gewild? Of een slimme tuin? Welnu, vanaf nu is dat eenvoudig met de Arduino IoT Cloud-compatible boards. Hiermee kunt u apparaten onderling koppelen, data visualiseren, en uw projecten vanuit de hele wereld beheren en delen. Of u een beginner bent of een professional, we kunnen u een breed scala aan abonnementen bieden om u alle ondersteuning te geven die u nodig heeft.Verbind uw sensoren en actuatoren over lange afstanden, en maak gebruik van de kracht van het LoRa draadloze protocol via LoRaWAN netwerken.Het Arduino MKR WAN 1310 board biedt een praktische en kosteneffectieve oplossing om LoRa connectiviteit toe te voegen aan projecten met een laag stroomverbruik. Dit open source board kan worden aangesloten op de Arduino IoT Cloud.Beter en efficiënterDe MKR WAN 1310 brengt een reeks verbeteringen met zich mee ten opzichte van zijn voorganger, de MKR WAN 1300. Hij is nog steeds gebaseerd op de Microchip SAMD21 low power processor, de Murata CMWX1ZZABZ LoRa-module, en de karakteristieke crypto-chip van de MKR-familie (de ECC508). Maar de MKR WAN 1310 bevat een nieuwe acculader, een 2 MByte SPI Flash en verbeterde grip op het stroomverbruik van het board.Verbeterde accuvoedingDeze laatste aanpassingen hebben de levensduur van de accu van de MKR WAN 1310 aanzienlijk verbeterd. Indien correct geconfigureerd is het stroomverbruik nu niet meer dan 104 uA! Om het board van spanning (5 V) te voorzien is het ook mogelijk om de USB-poort te gebruiken. Gebruik het board met of zonder accu’s, de keuze is aan u.Geheugen ingebouwdDatalogging en andere OTA (Over The Air) functies zijn nu ook mogelijk vanwege de ingebouwde 2 MByte Flash. Met deze nieuwe aantrekkelijke functie kunt u configuratiebestanden vanuit het netwerk naar het board overzetten, uw eigen scriptopdrachten maken, of eenvoudig gegevens lokaal opslaan, om deze pas te verzenden als de connectiviteit op zijn best is. Daarnaast voegt de crypto-chip van de MKR WAN 1310 extra beveiliging toe door inloggegevens en certificaten op te slaan in het embedded secure element.Deze functies maken het tot een perfecte IoT-node en bouwsteen voor low-power wide-area IoT apparaten.SpecificatiesDe Arduino MKR WAN 1310 is gebaseerd op de SAMD21 microcontroller. Microcontroller SAMD21 Cortex-M0+ 32-bit low power ARM MCU (datasheet) Radiomodule CMWX1ZZABZ (datasheet) Board voeding (USB/VIN) 5 V Secure element ATECC508 (datasheet) Ondersteunde accu’s Oplaadbare Li-Ion, of Li-Po, 1024 mAh minimale capaciteit Werkspanning van het board 3,3 V Digitale I/O pinnen 8 PWM pinnen 13 (0 .. 8, 10, 12, 18 / A3, 19 / A4) UART 1 SPI 1 I²C 1 Analog input pins 7 (ADC 8/10/12-bit) Analoge ingangspinnen 1 (DAC 10-bits) Analoge uitgangspinnen 8 (0, 1, 4, 5, 6, 7, 8, 16 / A1, 17 / A2) Gelijkstroom per I/O-pin 7 mA CPU flash geheugen 256 KB (intern) QSPI flash geheugen 2 MByte (extern) SRAM 32 KB EEPROM Nee Kloksnelheid 32.768 kHz (RTC), 48 MHz LED_BUILTIN 6 USB Full-Speed USB-device en embedded host Antenne versterking 2 dB (meegeleverde pentaband antenne) Carrier frequentie 433/868/915 MHz Dimensies 67,64 x 25 mm Gewicht 32 gr Downloads • Eagle-bestanden Schema Fritzing Pinout

    € 59,95

    Leden € 53,96

  • Bijna uitverkocht Arduino MKR IoT Bundle 1010 - Elektor

    Arduino Arduino MKR IoT Bundle 1010

    Nog 2 op voorraad

    Deze kit, met hierin de Ardino MKR WiFi 1010, biedt u de beste manier om de wereld van connected devices te leren kennen.De MKR IoT Bundle bevat alles wat je nodig hebt om je eerste ontwerp met connected devices te bouwen. Volg de 5 stapsgewijze tutorials die we voor u hebben voorbereid, en leer snel, door de elektronische componenten in de bundel te combineren, hoe u apparaten kunt configureren die verbinding maken met de Arduino IoT-cloud.Alles wat je nodig hebt om met IoT te beginnenDeze kit bevat alle hardware en software die nodig is om uw eerste IoT-apparaten te bouwen zonder extra kosten.Bouw 5 IoT-projectenAlle componenten zijn inbegrepen om uw ontdekkingsreis te beginnen met het bouwen van uw eigen IoT-projecten.Leer de Arduino IoT-cloud kennenLeer niet alleen over elektronica, maar ook over de mogelijkheden die de Arduino IoT-cloud u kan bieden.Inbegrepen 1x Arduino MKR1000 WiFi (met voorgemonteerde headers) 6x Fototransistoren 1x Tilt sensor 1x Temperatuursensor (TMP36) 3x Potentiometer 1x Piëzo capsule 10x drukknoppen 1x DC motor 1x Kleine servomotor 1x Alfanumeriek LCD-scherm (16x2 characters) 1x Optocoupler (4N35) 1x H-bridge motor driver (L293D) 2x Mosfet transistors (IRF520) 5x Condensatoren 100uF 70x Solid core jumper kabeltjes 1x Micro-USB kabel 1x Breadboard 1x LED (helder wit) 3x LED's (blauw) 1x LED (RGB) 8x LED's 5 mm (rood) 8x LED's 5 mm (groen) 8x LED's 5 mm (geel) 1x Mail pins strip (4x1) 1x Stranded jumper kabel (rood) 1x Stranded jumper kabel (zwart) 5x Diodes 20x 220 ? Weerstanden 5x 560 ? Weerstanden 5x 1 K? Q Weerstanden 5x 4,7 K? Weerstanden 20x 10 K? Weerstanden 5x 1 M? Weerstanden

    Nog 2 op voorraad

    € 109,95

    Leden € 98,96

  • Dragino MS14N - S Linux IoT Appliance with Sensor Terminal - Elektor

    Dragino Dragino MS14N-S Linux IoT Appliance met Sensor Terminal

    Niet op voorraad

    Het ondersteunt generieke OpenWrt Linux versie of gemodificeerde OpenWrt versie zoals Arduino Yun. Het heeft een USB host poort en heeft volledig Ethernet en 802.11 b/g/n WiFi mogelijkheden.Toepassingen voor MS14N zijn onder andere het op afstand besturen van robots, data logging, web applicaties voor data presentatie, mesh netwerken over WiFi en nog veel meer. Hardwaresysteem: CPU: AR9331 DDR RAM: 64 MB LASH: 16 MB Interface: 2 x 10 M/100 M RJ45 interface 1 x stroomingang: 9 ~ 12 VDC 1 x USB-hostpoort 1 x internet USB-interface 14 x schroef terminal posities WiFi Spec: Protocol: 802.11 b/g/n Frequentie: 2,412 - 2,472 GHz Vermogen: 100 mW

    Niet op voorraad

    € 49,95

    Leden € 44,96

  • Arduino Pro Nicla Sense ME - Elektor

    Arduino Arduino Pro Nicla Sense ME

    De Nicla Sense ME is een klein, energiezuinig tool dat een nieuwe standaard zet voor intelligente detectieoplossingen. Dankzij de eenvoudige integratie en schaalbaarheid van het Arduino ecosysteem combineert het board vier state-of-the-art sensoren van Bosch Sensortec: BHI260AP bewegingssensor systeem met geïntegreerde AI BMM150 magnetometer BMP390 druksensor BME688 4-in-1 gassensor, met AI en geïntegreerde hoge lineariteit, en zeer nauwkeurige druk-, vochtigheids- en temperatuursensoren. De Arduino Nicla Sense ME is het kleinste Arduino model tot nu toe, met een reeks sensoren van industriële kwaliteit samengepakt op een kleine afmeting. Hij meet proces parameters zoals temperatuur, vochtigheid en beweging. Met een 9-assige traagheidsmeter, en de mogelijkheid voor Bluetooth Low Energy connectiviteit, kan hij van pas komen bij het creëren van uw volgende Bluetooth Low Energy project. Maak uw eigen draadloze detectienetwerk van industriële kwaliteit met de ingebouwde BHI260AP, BMP390, BMM150 en BME688 Bosch sensoren.Functies Klein formaat, boordevol functies Laag stroomverbruik Sensor mogelijkheden toevoegen aan bestaande projecten Indien met accu’s gevoed wordt het een compleet zelfstandig board Krachtige processor, geschikt voor het hosten van intelligentie op de edge Meet bewegings- en omgevingsparameters Robuuste hardware, inclusief sensoren van industriële kwaliteit met embedded AI BLE-connectiviteit maximaliseert de compatibiliteit met professionele en consumentenapparatuur 24/7 always-on sensor dataverwerking bij ultralaag stroomverbruik Specificaties Microcontroller 64 MHz ARM Cortex-M4 (nRF52832) Sensoren BHI260AP – Zelflerende AI smart sensor met geïntegreerde versnellingsmeter en gyroscoopBMP390 – Digitale druksensorBMM150 – Geomagnetische sensorBME688 – Digitale laagvermogen gas-, druk-, temperatuur- en vochtigheidssensor met AI I/O Castellated pinnen met de volgende eigenschappen:1x I²C bus (met ext. ESLOV connector)1x seriële poort1x SPI2x ADC, programmeerbare I/O spanning van 1,8–3,3 V Connectiviteit Bluetooth 4.2 Voeding Micro USB (USB-B), Pin Header, 3,7 V Li-po accu met geïntegreerde acculader Geheugen 512 KB Flash / 64 KB RAM2 MB SPI Flash voor opslag2 MB QSPI speciaal voor BHI260AP Interface USB-interface met debug functionaliteit Afmetingen 22,86 x 22,86 mm Gewicht 2 gr DownloadsDatasheet

    € 84,95

    Leden € 76,46

  • Portable Smart WiFi Weather Station - Elektor

    Generic Draagbaar Smart WiFi Weerstation

    Dit draagbare wifi-weerstation is de perfecte combinatie van functionaliteit en stijl en biedt realtime updates over temperatuur, luchtvochtigheid en tijd – allemaal in één oogopslag. Dankzij een helder digitaal display zorgt het station ervoor dat weer- en tijdgegevens altijd gemakkelijk af te lezen en te begrijpen zijn. Het minimalistische ontwerp integreert naadloos in elke omgeving en voegt een vleugje moderne verfijning toe zonder onnodig de aandacht te trekken. Kenmerken Multifunctioneel display: Geeft weer, luchtdruk, minimale/maximale temperatuur, windsnelheid, plaats, land/regio, datum, dag van de week, buitentemperatuur en Luchtvochtigheid – alles in één oogopslag. Aangepaste GIF-animaties: upload je eigen GIF's voor een gepersonaliseerde weergave-ervaring. Wifi-connectiviteit: maakt automatisch verbinding met internet om realtime weer- en tijdgegevens op te halen. Aangedreven door USB-C Duurzame kunststof behuizing Afmetingen: 45 x 35 x 40 mm

    € 24,95

    Leden € 22,46

  • IoTize TapNLink WiFi, BLE, NFC - Elektor

    IoTize IoTize TapNLink WiFi, BLE, NFC

    TapNLink modules provide wireless interfaces for linking electronic systems to mobile devices and the Cloud. TapNLink connects directly to the target system's microcontroller. It integrates into and is powered by the target system. All TapNLink products are easily configured to control access by different types of users to data in the target system.TapNLink facilitates rapid creation of Human Machine Interfaces (HMI) that run on Android, iOS and Windows mobiles. HMI apps are easily customized for different users and can be deployed and updated to keep pace with evolving system requirements and user needs.TapNLink Wi-Fi modules can also be configured to connect the target system permanently to a wireless network and the Cloud. This enables permanent logging of target system data and alarms.Features Wireless Channels Wi-Fi 802.11b/g/n Bluetooth Low Energy (BLE 4.2) Near Field Communication (NFC) Type5 tag (ISO/IEC 15693) Supported Target Connections: Connects on 2 GPIO of the target microcontroller and supports: Serial interface with Software Secure Serial Port (S3P) protocol Serial interface with ARM SWD debug protocol. UART with Modbus protocol Mobile Platform Support HTML5 web apps (Android, iOS) API for Cordova (Android, iOS, Windows 10) Java (Android, iOS native) Auto-app generator for Android and iOS mobiles Security Configurable access profiles Configurable, encrypted passwords AES-128/256 module-level data encryption Configurable secure pairing with NFC Dimensions: 38 mm x 28 mm x 3 mm Electrical Characteristics Input voltage: 2.3V to 3.6 V Low power consumption: Standby: 100 µA NFC Tx/Rx: 7 mA Wi-Fi Rx: 110 mA Wi-Fi Tx : 280 mA (802.11b) Temperature Range: -20°C - +55°C Compliance CE (Europe), FCC (USA), IC (Canada) REACH RoHS WEEE Ordering Information Base Part Number: TnL-FIW103 MOQ: 20 modules TapNLink modules pre-qualified, pre-programmed and ready to configure. IoTize Studio configuration and testing software Software for HMI on mobile devices (iOS, Android, Windows 10) IoTize Cloud MQTT infrastructure (open source) For more information, check out the datasheet here.

    € 32,95

    Leden € 29,66

  • ISM Band Outdoor Antenna (868 MHz) - Elektor

    OPA Design ISM Band Buitenantenne (868 MHz)

    Deze buitenantenne van glasvezel is geoptimaliseerd voor het ontvangen van signalen in de 868 MHz ISM-band en ondersteunt technologieën zoals Sigfox, LoRa, Mesh Networks en Helium. De antenne bestaat uit een halvegolfdipool met een versterking van 4,4 dBi, ingekapseld in een glasvezelradome met een aluminium montagebasis. Specificaties Frequentie 868-870 MHz Antennetype Dipool 1/2 golf Connector N vrouwelijk Installatietype Mastdiameter 35-60 mm (montagebeugel meegeleverd) Winst 4,4 dBi SWR ≤1,5 Type polarisatie Verticaal Maximaal vermogen 10 W Impedantie 50 Ohm Afmetingen 52,5 cm Buisdiameter 26 mm Basisantenne 32 mm Bedrijfstemperatuur −30°C tot +60°C Inbegrepen ISM-bandantenne (868 MHz) Mastbeugel (voor installatie op een mast met een diameter van 35 tot 60 mm)

    € 69,95

    Leden € 62,96

  • CubeCell HTCC - AB02 LoRa Development Board (EU868) - Elektor

    Heltec Automation CubeCell HTCC-AB02 LoRa Development Board (EU868)

    The CubeCell series is designed primarily for LoRa/LoRaWAN node applications. Built on the ASR605x platform (ASR6501, ASR6502), these chips integrate the PSoC 4000 series MCU (ARM Cortex-M0+ Core) with the SX1262 module. The CubeCell series offers seamless Arduino compatibility, stable LoRaWAN protocol operation, and straightforward connectivity with lithium batteries and solar panels. The HTCC-AB02 is a developer-friendly board, ideal for quickly testing and validating communication solutions. Features Arduino compatible Based on ASR605x (ASR6501, ASR6502), those chips are already integrated the PSoC 4000 series MCU (ARM Cortex M0+ Core) and SX1262 LoRaWAN 1.0.2 support Ultra low power design, 3.5 uA in deep sleep Onboard SH1.25-2 battery interface, integrated lithium battery management system (charge and discharge management, overcharge protection, battery power detection, USB/battery power automatic switching) Good impendence matching and long communication distance Onboard solar energy management system, can directly connect with a 5.5~7 V solar panel Micro USB interface with complete ESD protection, short circuit protection, RF shielding, and other protection measures Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing Onboard 0.96-inch 128x64 dot matrix OLED display, which can be used to display debugging information, battery power, and other information Specifications Main Chip ASR6502 (48 MHz ARM Cortex-M0+ MCU) LoRa Chipset SX1262 Frequency 863~870 MHz Max. TX Power 22 ±1 dBm Max. Receiving Sensitivity −135 dBm Hardware Resource 2x UART1x SPI2x I²C1x SWD3x 12-bit ADC input8-channel DMA engine16x GPIO Memory 128 Kb FLASH16 Kb SRAM Power consumption Deep sleep 3.5 uA Interfaces 1x Micro USB1x LoRa Antenna (IPEX)2x (15x 2.54 Pin header) + 3x (2x 2.54 Pin header) Battery 3.7 V lithium battery (power supply and charging) Solar Energy VS pin can be connected to 5.5~7 V solar panel USB to Serial Chip CP2102 Display 0.96" OLED (128 x 64) Operating temperature −20~70°C Dimensions 51.9 x 25 x 8 mm Included 1x CubeCell HTCC-AB02 Development Board 1x Antenna 1x 2x SH1.25 battery connector Downloads Datasheet Schematic Quick start GitHub

    € 34,95

    Leden € 31,46

  • CubeCell HTCC - AB02S LoRa Development Board with GPS (EU868) - Elektor

    Heltec Automation CubeCell HTCC-AB02S LoRa Development Board with GPS (EU868)

    The CubeCell series is designed primarily for LoRa/LoRaWAN node applications. Built on the ASR605x platform (ASR6501, ASR6502), these chips integrate the PSoC 4000 series MCU (ARM Cortex-M0+ Core) with the SX1262 module. The CubeCell series offers seamless Arduino compatibility, stable LoRaWAN protocol operation, and straightforward connectivity with lithium batteries and solar panels. The HTCC-AB02S is a developer-friendly board with an integrated AIR530Z GPS module, ideal for quickly testing and validating communication solutions. Features Arduino compatible Based on ASR605x (ASR6501, ASR6502), those chips are already integrated the PSoC 4000 series MCU (ARM Cortex M0+ Core) and SX1262 LoRaWAN 1.0.2 support Ultra low power design, 21 uA in deep sleep Onboard SH1.25-2 battery interface, integrated lithium battery management system (charge and discharge management, overcharge protection, battery power detection, USB/battery power automatic switching) Good impendence matching and long communication distance Onboard solar energy management system, can directly connect with a 5.5~7 V solar panel Micro USB interface with complete ESD protection, short circuit protection, RF shielding, and other protection measures Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing Onboard 0.96-inch 128x64 dot matrix OLED display, which can be used to display debugging information, battery power, and other information Using Air530 GPS module with GPS/Beidou Dual-mode position system support Specifications Main Chip ASR6502 (48 MHz ARM Cortex-M0+ MCU) LoRa Chipset SX1262 Frequency 863~870 MHz Max. TX Power 22 ±1 dBm Max. Receiving Sensitivity −135 dBm Hardware Resource 2x UART1x SPI2x I²C1x SWD3x 12-bit ADC input8-channel DMA engine16x GPIO Memory 128 Kb FLASH16 Kb SRAM Power consumption Deep sleep 21 uA Interfaces 1x Micro USB1x LoRa Antenna (IPEX)2x (15x 2.54 Pin header) + 3x (2x 2.54 Pin header) Battery 3.7 V lithium battery (power supply and charging) Solar Energy VS pin can be connected to 5.5~7 V solar panel USB to Serial Chip CP2102 Display 0.96" OLED (128 x 64) Operating temperature −20~70°C Dimensions 55.9 x 27.9 x 9.5 mm Included 1x CubeCell HTCC-AB02S Development Board 1x Antenna 1x 2x SH1.25 battery connector Downloads Datasheet Schematic GPS module (Manual) Quick start GitHub

    € 49,95

    Leden € 44,96

Wat is het Internet of Things (IoT)?

Het Internet of Things, of IoT, is een systeem van onderling verbonden computer-apparaten, fysieke objecten met sensoren, verwerkingsvermogen, software, en andere technologieën die unieke identificatiecodes (UID) hebben. Het IoT netwerk heeft te maken met de communicatie tussen machines, de identificatie van apparaten, en de communicatie. Daarom is het kiezen van het beste draadloze netwerk op basis van de IoT specificaties essentieel.

IoT apparaten kunnen gegevens over een netwerk overbrengen zonder dat interactie van mens tot mens of van mens tot computer nodig is. Daardoor kunnen gebruikers moeilijkheden ondervinden met beveiliging, integratie, procescapaciteit, schaalbaarheid, en toegankelijkheid. Om deze problemen op te lossen is een slimme aanpak van het beheer van IoT apparaten nodig.

Wat zijn LoRa en LoRaWAN?

LoRa maakt transmissies over zeer grote afstanden mogelijk (meer dan 10 km in landelijke gebieden) met een laag stroomverbruik. Het is wereldwijd een veel gebruikte technologie voor IoT netwerken. Dankzij de LoRa technologie kunnen we enkele van 's werelds grootste problemen oplossen: energiebeheer, vermindering van natuurlijke hulpbronnen, milieubescherming, efficiëntie van infrastructuur, rampenbestrijding, en meer.

De lage bandbreedte van LoRa kan echter niet voor zomaar elke toepassing gebruikt worden. Als gevolg van beperkingen in het frequentiebereik dat het gebruikt, is het protocol niet in staat continu te zenden.

LoRaWAN is een low-power, wide area networking protocol dat gebouwd is op de LoRa radiomodulatietechniek. Het verbindt apparaten draadloos met het Internet en beheert de communicatie tussen end-node apparaten en netwerk gateways. Zo definieert LoRaWAN het communicatieprotocol en de systeemarchitectuur voor het netwerk, terwijl de fysieke laag van LoRa de communicatieverbinding over lange afstand mogelijk maakt, met de hulp van de gateway.

De gateway helpt om transmissie van een elektrisch apparaat naar de cloud te realiseren, vooral in omgevingen waar andere soorten netwerken door technische beperkingen niet bruikbaar zijn.

Wat kun je met LoRa technologie doen? Wat biedt Elektor aan? Welke accessoires zijn er?

LoRa is een uitstekende keuze voor gebruik binnenshuis in een breed spectrum van toepassingen, waaronder smart cities, gebouwen, landbouw, meting, gezondheidszorg, en logistiek. Het is veilig, bidirectioneel, low-power, en heeft een groot bereik.

Accessoires helpen gebruikers hun IoT opstellingen te optimaliseren. Elektor biedt een ruime keuze aan componenten, waaronder gateways, RFID-lezers, IoT-shields, en verschillende soorten sensoren (bv. temperatuur, positie, en luchtvochtigheid) om aan de diverse behoeften van een groot aantal klanten te voldoen.

De toekomst van LoRa

LoRa zal de kosten helpen verlagen om IoT oplossingen te maken en grootschalige IoT toepassingen mogelijk te maken. Verwacht wordt dat het een sleutelrol zal spelen als communicatienetwerk. We verwachten bijvoorbeeld dat het gebruikt zal worden voor een breed scala van toepassingen, zoals talloze slimme verlichtingssystemen, het volgen van het gebruik van waterkracht, en industriële gegevensbewaking en -analyse.

Login

Wachtwoord vergeten?

Heb je nog geen account?
Maak account aan