Displays & LED's

The Diamex LED Tube Clock ESP Kit has a WLAN interface, with which the current highly accurate time can be retrieved directly from the Internet via the home router. In addition, a battery-buffered real-time clock is built in, which takes over when no WLAN is available. The WLAN access data are configured via the LED-Basic development environment (from version 15.3.0). The Diamex LED Tube Clock ESP Kit can be operated worldwide, the time zone can be chosen arbitrarily. The winter/summer time changeover is done automatically. Specifications 8-digit, bright 7-segment display Real-time clock including mounting bracket for a CR2012 battery Time setting via PC, WLAN or directly at the clock 4 buttons Beeper (sound output) Micro USB port for power supply, basic data, bios update and terminal output Board size: approx. 130 x 75 mm

Lees meer minder

This 7' touch display convinces with its variety of different application possibilities. The display can be connected via HDMI as well as via VGA. It has a 3.5 mm audio connector and a 4-pin JST-connector, to which headphones or two 2 W / 5 ? speakers can be connected. The integrated software allows you to configure settings such as contrast and brightness using the buttons on the side.Specifications LCD type IPS Resolution 1024 x 600 Contrast 800:1 Brightness 350 CD/m² Multitouch Capacitive, 5 Points Connections Connections HDMI, VGA, Audio 3.5 mm, JST connector for two 2 W / 5 ? speaker Power supply 5 V/2 A Viewing angle 175° Colors 16,7 M Further special features Additional solder pads to lead the buttons to the Dimensions 165 x 124 x 13 mm Included 1x 7' Display 1x microUSB-cable 1x VGA-cable 1x HDMI-cable 1x HDMI-microHDMI-cable Downloads Datasheet Manual

Lees meer minder

De traditionele 16x2 LCD heeft tot 10 I/O pinnen nodig voor de weergave, en de 16x2 LCD met RGB achtergrondverlichting heeft nog eens 3 extra pinnen nodig om de kleur van de achtergrondverlichting te regelen. Dit neemt veel I/O-pinnen in beslag op de hoofdbesturingskaart, vooral voor ontwikkelingskaarten met minder I/O-bronnen, zoals Arduino en Raspberry Pi. Met behulp van de Grove I2C connector zijn slechts 2 signaalpennen en 2 voedingspennen nodig. Je hoeft niet eens zorgen te maken over hoe deze pinnen aan te sluiten. Gewoon aansluiten op de I2C interface op Seeeduino of Arduino/Raspberry Pi+baseshield via de Grove kabel. Geen ingewikkelde bedrading, geen solderen, geen zorgen te maken over het verbranden van de LCD veroorzaakt door de verkeerde stroombegrenzende weerstand. Easy peasy. Specificaties Afmetingen: 83 mm x 44 mm x 13 mm Gewicht: 42 g Batterij: Exclusief Ingangsspanning: 5 V

Lees meer minder

Specifications Resolution 1920 x 1080 Screen Size 15.6' Refresh Rate 60 Hz Contrast 800:1 Brightness 300 nit Screen Type TFT IPS LCD Backlight LED Backlight Color Gamut 16.7M, NTSC 72%, sRGB up to 100% Speaker Double Speaker Viewing Angle 178 ° Aspect Ratio 16:9 Power Supply 5 - 20 V or Type-C USB 3.0 Inputs Mini HDMI, Type-C, Voltage Input Outputs 3.5 mm Jack Plug Operating Temperature 0 °C - 50°C Case Aluminum Alloy Dimensions 360 mm x 230 mm x 10 mm Weight 1390 g Included Joy-View 15 Display Smart Case 1.5m HDMI to mini-HDMI cable 1m Type-C to Type-C cable 1m USB-A to USB-C cable Power Adapter HDMI to mini HDMI adapter Cleaning Towel

Lees meer minder

Dit mini IPS 7' HD scherm ondersteunt een resolutie van 1024x600. IPS schermen helpen kleuren consistent te houden bij een brede kijkhoek. De 2 verwijderbare luidsprekers zorgen voor een verbeterde audiovisuele ervaring.Kenmerken Via vier schroefgaten in de hoeken kun je dit kleine scherm monteren op de doe-het-zelf IoT-projecten waar je aan werkt. Dit Raspberry Pi scherm wordt geleverd met 2 standaards, is eenvoudig te installeren en te verwijderen, en ideaal voor gebruik onderweg. Door dit capacitieve USB touchscreen via de USB touch poort te voeden wordt de aanraakfunctie geactiveerd en hoeft er geen driver te worden geïnstalleerd, gewoon plug and play! Beeldsignalen worden verstuurd via een HDMI-compatibele poort, voeding & touch via de micro-USB poort, zonder drivers. Dus geen aparte bekabeling nodig voor de Raspberry Pi 4, maar eenvoudig met behulp van 2 eenvoudige adapters rechtstreeks op de Raspberry Pi 4 aan te sluiten. Te gebruiken met de Raspberry Pi 4/3/2, laptop, tv, videogameconsole zoals Nintendo Switch / Xbox / PS4 of met een beveiligingscamera. 170 graden brede kijkhoek. 5-punts capacitief HD touchscreen. Specificaties Schermgrootte 7-inch (154 x 86 mm) Resolutie 1024 x 600 Weergavetype IPS Aanraking Capacitief touchscreen Frame rate 60 fps Helderheid 260 cd/m² Luidsprekers Ondersteund Interface HD & USB Werktemperatuur ?20 tot +60°C Afmetingen 164 x 99 mm Gewicht 235 g Inbegrepen 1x 7-inch scherm 1x USB naar micro-USB connector 1x HD naar micro-HD connector 1x USB naar micro-USB kabel 1x HD-naar-HD kabel 4x M2,5 schroeven 4x Kleine koperen pilaren 2x Pro Stand 2x M3 schroeven 2x Luidsprekers 1x Gebruikershandleiding DownloadsGebruikershandleiding

Lees meer minder

The Unicorn Pack fits nicely on the back of your Pico - with a tidy 7x16 matrix (that's 112 RGB LEDs!) it's surely the fanciest backpack going. The four tactile buttons can be used to switch between modes, as controls for simple games, or adjusting brightness. It's possible to control the colour and brightness of each LED individually so you can use it to display animations, text, simple images, and more. Make a mini photo FX lamp, a smart status light for Zoom, use it to display colourful scrolling messages on your fridge, or just enjoy some pretty animations. Features 16x7 matrix of RGB LEDs (112 total) Individual colour/brightness control of each LED 4 x tactile buttons Pre-soldered female headers for attaching to Pico Compatible with Raspberry Pi Pico. Fully assembled No soldering required (as long as your Pico has header pins attached). Dimensions: approx 62mm x 25mm x 10mm (L x W x H, including headers and buttons) C/C++ and MicroPython libraries

Lees meer minder

Features LEDs: 5 x 5 x 5 = 125 LEDs User programmable via USB (creation of animation/scenes) Large amount of user programmable frames Frames are separately dimmable 4 transition speeds Available frames: 3200 5 levels LED dimming available No coding skills required Software similar to (3 x 3 x 3) Specifications Regulated power supply: 9 VDC (not incl.) Power consumption: 300 mA max. Dimensions: 110 x 110 x 150 mm / 4.33 x 4.33 x 5.9?

Lees meer minder

Arduino, MicroPython, and CircuitPython-compatible compact development board powered by Raspberry Pi RP2040RP2040-0.42LCD is a high-performance development board with integrated 0.42' LCD (70x40 resolution) with flexible digital interfaces.It incorporates Raspberry Pi's RP2040 microcontroller chip. The RP2040 features a dual-core Arm Cortex-M0+ processor clocked at 133 MHz with 264 KB internal SRAM and 2 MB flash storage.Specifications SoC Raspberry Pi RP2040 dual-core Cortex-M0+ microcontroller at up to 125 MHz, with 264 KB SRAM Storage 2 MB SPI flash Display 0.42-inch OLED USB 1x USB Type-C port for power and programming Expansion – Qwiic I²C connector– 7-pin and 8-pin headers with up to 11x GPIOs, 2x SPI, 2x I²C, 4x ADC, 1x UART, 5 V, 3.3 V, VBAT, GND Misc – Reset and Boot buttons– RGB LED, power LED Power supply – 5 V via USB-C port or Vin– VBAT pin for battery input– 3.3 V regulator with 500 mA peak output Dimensions 23.5 x 18 mm Weight 2.5 g DownloadsGitHub

Lees meer minder

Inky Frame 5.7' features a nice, big seven color E Ink display with loads of space for displaying images, text, graphs or interfaces. There's five buttons with LED indicators for interacting with the display, two Qw/ST connectors for plugging in breakouts and a micro SD card slot for all-important storage of cat photos.Every Inky Frame comes with a pair of sleek little metal legs so you can stand it up on your desk (and a selection of mounting holes if you'd prefer to do something else). There's also a battery connector so you can power it without annoying trailing wires, and some neato power saving features that mean you can run it from batteries for ages.Inky Frame is great for: Checking your calendar and upcoming appointments at a glance Attaching to your office door to display your availability Displaying motivational posters, quotes, or images (fungible or otherwise) Showing readouts from other wirelessly connected environmental boards Features Raspberry Pi Pico W Aboard Dual Arm Cortex M0+ running at up to 133 Mhz with 264 kB of SRAM 2 MB of QSPI flash supporting XiP Powered and programmable by USB micro-B 2.4 GHz wireless 5.7' EPD display (600 x 448 pixels) E Ink Gallery Palette 4000 ePaper ACeP (Advanced Color ePaper) 7-color with black, white, red, green, blue, yellow, orange. Ultra wide viewing angle – >170° Dot pitch – 0.1915 x 0.1915 mm 5x Tactile buttons with LED indicators Two Qw/ST connectors for attaching breakouts microSD card slot Dedicated RTC chip (PCF85063A) for deep sleep/wake Fully assembled No soldering required. C/C++ and MicroPython libraries Schematic Included 1x Inky Frame 5.7' (incl. Pico W) 2x Metal legs DownloadsMicroPython (Learn) Getting Started with Inky Frame (Readme) Installing MicroPython (Readme) MicroPython FAQs (and troubleshooting) Download pirate-brand MicroPython (you'll want the Inky Frame.uf2) MicroPython examples PicoGraphics function reference C/C++ C examples Picographics function reference

Lees meer minder

Een open source 2,7 inch IoT-scherm met laag stroomverbruik, aangestuurd door een ESP32-S2 module en voorzien van SHARP's Memory-in-Pixel (MiP) schermtechnologieDe Newt is een permanent werkend beeldscherm voor wandmontage dat op batterijen werkt , en online gaat om het weer, kalenders, sportuitslagen, to-do lijsten, notities... op te halen, eigenlijk alles wat op het internet te vinden is! Het wordt aangestuurd door een ESP32-S2 microcontroller die je kunt programmeren met Arduino, CircuitPython, MicroPython, of ESP-IDF. Het is perfect voor makers: Sharp's Memory-in-Pixel (MiP) technologie vermijdt de trage refresh tijden van E-Ink schermen. Een real-time klok (RTC) werd toegevoegd ter ondersteuning van timers en alarmen. De Newt is ontworpen met batterijvoeding in gedachten; elk onderdeel op de printplaat is gekozen vanwege zijn specificaties om op een laag stroomverbruik te werken. Newt is ontworpen om 'snoerloos' te werken, wat betekent dat hij gemonteerd kan worden op plaatsen waar een netsnoer onhandig zou zijn, bijvoorbeeld een muur, koelkast, spiegel of droogbord. Met de optionele standaard zijn bureaus, planken en nachtkastjes ook goede opties.Newt is open source, en alle ontwerpbestanden en bibliotheken zijn beschikbaar voor beoordeling, gebruik en wijziging. Dat is echter niet verplicht. Elke Newt wordt geleverd met werkende code met de volgende eigenschappen: Actuele weerdetails Uurlijkse en dagelijkse weersvoorspelling Alarm Timer Inspirerende notities Voorspelling luchtkwaliteit Gewoonte kalender Pomodoro timer Strategiekaarten Alleen het volgen van de instructies voor Wi-Fi voorziening is nodig om te beginnen. Er zijn geen app-downloads nodig.Specificaties Display Sharp Memory LCD Scherm afmetingen 2,7 inch Resolutie 240 x 400 Deep sleep stroomverbruik 30 uA Verversingssnelheid < 0.001 s Periodieke verversing van het scherm vereist Nee Invoerknoppen 10 capacitieve pads, 1 drukknop RTC inbegrepen Ja Luidspreker inbegrepen Ja Voedingsingang USB Type-C Batterijen inbegrepen Nee Programmeertalen Arduino, CircuitPython, ESP IDF, MicroPython Afmetingen 91 x 61 x 9 mm Microcontroller Espressif ESP32-S2-WROVER Module met 4 MB flash en 2 MB PSRAM Geschikt voor Wi-Fi Ondersteunt Arduino, MicroPython, CircuitPython en ESP-IDF Deep sleep stroom van 25 ?A Display 2,7-inch MiP LCD met 240 x 400 pixels Biedt contrastrijke weergave met hoge resolutie en lage latency bij zeer laag stroomverbruik Reflecterende modus gebruikt omgevingslicht en maakt achtergrondverlichting overbodig Bijhouden van de tijd, timers en alarmen Micro Crystal RV-3028-C7 RTC Geoptimaliseerd voor extreem laag stroomverbruik (45 ?A) Kan tegelijkertijd een periodieke timer, een afteltimer en een alarm beheren Hardware-interrupt voor timers en alarmen 43 bytes non-volatile user memory, 2 bytes user RAM Aparte UNIX tijdteller BuzzerLuidspreker/zoemer met mini-klasse-D versterker op DAC-uitgang A0, kan tonen of lo-fi audioclips weergevenGebruikersinvoer Aan/uit-schakelaar Twee programmeerbare aanraaktoetsen voor reset en opstarten 10 capacitieve touch-pads StroomvoorzieningNewt is ontworpen om met een 500 mAH LiPo batterij één tot twee maanden te kunnen werken tussen twee oplaadbeurten. De exacte werkingsduur varieert. (Vooral door intensief gebruik van Wi-Fi zal de batterij sneller leeg raken.) USB Type-C connector voor programmeren, voeding en opladen Spanningsregelaar met lage ruststroom (TOREX XC6220) die 1 A stroom kan leveren en verbruikt slechts 8 ?A in power saving mode. JST-connector voor een Lithium-Ion batterij Batterij-oplaadcircuit (MCP73831) Batterij-indicator (1 ?A ruststroom) Software Newt hardware is compatibel met open-source Arduino bibliotheken voor ESP32-S2, Adafruit GFX (fonts), Adafruit Sharp Memory Display (display writing), en RTC RV-3028-C7 (RTC). Arduino-bibliotheken en voorbeeldprogramma's zijn in ontwikkeling en zullen voor de lancering beschikbaar zijn in onze GitHub repository. CircuitPython bibliotheken en registratie staan op de planning, met de ontwikkeling van een CircuitPython bibliotheek voor de RV-3028 real-time klok als belangrijke voorwaarde. Inbegrepen Phambili Newt – Volledig gemonteerd met voorgeïnstalleerde firmware Lasergesneden bureaustandaard Voetjes met mini-magneet Benodigde schroeven Support & Documentatie Complete gebruikersinstructies GitHub: Arduino Library en Codebase GitHub: Schema van het board Video's van prototypes of demos (de bouw is te volgen op Hackaday)

Lees meer minder

Circuit Playground Bluefruit is the third board in the Circuit Playground series, another step towards a perfect introduction to electronics and programming. Adafruit has taken the popular Circuit Playground Express and made it even better! Now the main chip is an nRF52840 microcontroller which is not only more powerful, but also comes with Bluetooth Low Energy support for wireless connectivity. The board is round and has alligator-clip pads around it so you don't have to solder or sew to make it work. You can power it from USB, a AAA battery pack, or with a Lipoly battery (for advanced users). Circuit Playground Bluefruit has built-in USB support. Built in USB means you plug it in to program it and it just shows up, no special cable or adapter required. Just program your code into the board then take it on the go! Features 1x nRF52840 Cortex M4 processor with Bluetooth Low Energy support 10x mini NeoPixels, each one can display any color 1x Motion sensor (LIS3DH triple-axis accelerometer with tap detection, free-fall detection) 1x Temperature sensor (thermistor) 1x Light sensor (phototransistor). Can also act as a color sensor and pulse sensor. 1x Sound sensor (MEMS microphone) 1x Mini speaker with class D amplifier (7.5 mm magnetic speaker/buzzer) 2x Push buttons, labeled A and B 1x Slide switch 8x alligator-clip friendly input/output pins Includes I²C, UART, 6 pins that can do analog inputs, multiple PWM outputs Green 'ON' LED so you know its powered Red '#13' LED for basic blinking Reset button 2 MB of SPI Flash storage, used primarily with CircuitPython to store code and libraries. MicroUSB port for programming and debugging USB port can act like serial port, keyboard, mouse, joystick or MIDI! Specifications Outer Diameter: ~50.6 mm / ~2.0' Weight: 8.9 g

Lees meer minder

Up to 2048 digital PWM LEDs can be comfortably managed and easily controlled by the Diamex LED Player M. Equipped with eight channels, small and even larger projects for party lighting, video boards or professional lighting installations can be implemented quickly. Live videos on a panel surface are possible as well as stored sequences, light moods or effect installations for small and large lighting performances. Applications such as party lighting, home cinema installations, pool lighting, garden and home lighting, moving stores or sophisticated LED lighting solutions indoors or outdoors - all no longer a problem. With the Diamex LED Player M the imagination has no limits. At the same time, the module is small, compact and highly configurable. Via USB, Windows pads or notebooks and PCs can be used as feed players. Free software like JINX! or gLEDiator are perfectly suited for home and professional applications. These sequences can also be stored as a file on a simple mini-SD card and inserted into the Diamex LED Player M, turning the module into a stand-alone light jockey. Simply put, it's a real powerhouse equipped with state-of-the-art Cortex M4 microcontroller technology, a real highlight for professionals and amateurs alike, which can handle a wide variety of strips and matrices and is also future-proof via online firmware update. Specifications LED panel programs like JINX or GLEDIATOR can send their data directly to the Diamex LED Player M via the USB port. Maximum capacity: 512 LEDs per channel, 2048 LEDs in total. Different LED protocols are supported, both for LEDs with only one asynchronous data line (single wire) and LEDs with synchronous DATA and TAKT lines (dual wire). LEDs, Stripes, Panels of the following types are supported: WS2811/12 (compatible UCS1903, PL9823), APA106, WS2821 (DMX), WS2801, APA102, LPD8803/06. Mini-USB 2.0 port for virtual COM port (player for JINX, GLEDIATOR etc.), configuration and updates via bootloader. 2 buttons for sequence control. Screw terminals for LED data outputs and power supply. Fully configurable via PC-Tool: Protocol for PC data, LED protocol, number of connected strips or panels, arrangement of colours in the data stream, length of strips, size of panels and arrangement of LEDs on panels, mirroring, timing parameters of protocols. MicroSD card slot for playing files in TPM2 format even without a PC. SD cards can be read and written directly from a PC as a virtual drive. Status LEDs for system and SD card. Controlled by powerful 32-bit Cortex-M4 microcontroller Board size: 71 x 31mm

Lees meer minder

The Electric Paint Lamp Kit is a great gift! Transform any piece of paper into a touch-sensitive lamp with Electric Paint! Make three paper lamps with no tools, no programming, no special skills required. Included 1x Light Up Board 1x Electric Paint 10ml Tube 1x Micro USB Cable 1x Touch Lamp Template 1x Dimmer Lamp Template 1x Proximity Lamp Template 1x Instruction Test Sheet Transform a paper template into a beautiful lamp in three easy steps. Paint, plug, and play! Use Electric Paint to create custom touch-sensitive buttons connected to our Light Up Board and then use our lampshades to bring your lamp to life. LEVEL: Beginner The Electric Paint Lamp Kit is easy to use and makes a perfect gift. The Touch, Dimmer, and Proximity lamps all show off different aspects of Electric Paint and the Light Up Board and are perfect for your home, office or workshop. About Electric Paint Your design and electronics projects are about to change forever with this easy to use electrically conductive paint. Paint circuits or use as a conductive adhesive on almost anything including paper, plastic, textiles and conventional electronics. About the Light Up Board The Light Up Board is the heart of the Electric Paint Lamp Kit. It works straight out of the box, is powered by USB and requires no programming or special tools. The board’s six bright LEDs and three different modes provide the light for your lamps and the super easy connector system means that you can create lamps on any sheet material.

Lees meer minder

De Ulanzi TC001 is een LED pixelklok bestaande uit 256 individueel adresseerbare RGB LED's (8x32), met ingebouwde accu, zoemer, licht-, temperatuur- en vochtigheidssensor. De geïntegreerde oplaadbare accu biedt een gebruikstijd van maximaal 5 uur. De WiFi-verbinding met de klok wordt gemaakt via een ESP32-chip. De Ulanzi TC001 maakt gebruik van een ESP32-WROOM-32D module. Kenmerken Pixel weergave. Gelijktijdige weergave van het aantal volgers: groei van het aantal fans is direct zichtbaar, geschikt voor YouTube, Bilibili en Weibo. Pomodoro Clock Design: beheer je eigen tijd op een meer wetenschappelijke wijze. Ontdek de onbegrensde mogelijkheden: er kunnen meerdere programma's via de besturingsserver worden geïnstalleerd om meerdere functies te creëren. Awtrix maakt het beter: de Awtrix simulator in de firmware van de TC001 simuleert een Awtrix matrix, en stelt u in staat om de klok te besturen met behulp van een standaard Awtrix host. Een hi-tech en indrukwekkend uiterlijk: eenvoudig de juiste sfeer te creëren, een LED-kleuren pixelscherm met een beter beeld. Een ingebouwde 4400 mAh accu met een accu gebruiksduur tot 5 uur. Specificaties Aantal LED's: 256 (8x32) Bedrijfsspanning: 3,7 V Verbruik: 3 W Accu capaciteit: 4400 mAh Interface: USB-C Afmetingen: 200,6 x 70,3 x 31,9 mm Gewicht: 283 g Inbegrepen Ulanzi TC001 Smart Pixel Clock USB-kabel Handleiding Downloads Firmware

Lees meer minder

De Ynvisible Segment E-Paper Displays zijn dun & flexibel, zonlicht leesbaar, zeer eenvoudig te bedienen, en dat ze de meest energie-efficiënte display technologie op de markt voor de meeste toepassingen. Ga vandaag nog aan de slag! Evalueer de ultra-low-power, dunne en flexibele Segment E-Paper Displays. De kit bevat display-ontwerpen en bevat zowel een handmatige display-driver als een display-driver met I²C-interface. Display parameters White Reflectance 40% Contrastverhouding (Yb/Yd) 1:3 Afhankelijkheid van de hoek Nee, lambertiaan Dikte 300 µm Grafische opmaak Segmenten Afmetingen segmenten 1-100 mm Responstijd 100-1000 ms Power parameters Aandrijfspanning 1,5 V Aandrijfmethode Directe aandrijving Energieverbruik 1 mJ/cm^2 Pulsenergie 0,25 mJ/cm^2 Beeldbehoud zonder stroom 1-5 minuten Bedrijfsomstandigheden -20°C - +60°C Activeringen/cycli 1.000.000 Inbegrepen Onzichtbare Segment Displays (Gesegmenteerde e-paper displays met verschillende lay-outs, vormen en symbolen, geschikt voor testen en evaluatie.) 3 eencijferig display 1 dubbelcijferig display 5 displays met één segment/icoon 4 voortgangsbalken (7-segment en 3-segment) Handmatige display-klikker (handmatige display-controller voor aan/uit-bediening) Display-driver en softwarebibliotheek (Speciale display-driver met I²C-communicatie-interface. Compatibel met Arduino en andere gebruiksvriendelijke ontwikkelborden) Flexibele display-adapter (Voor gemakkelijke aansluiting van flexibele displays op een plastic ondergrond op harde elektronica (zoals ontwikkelborden), met behulp van een FFC/FPC-connector.) Downloads Datasheet Gids & instructies

Lees meer minder

Resolution 1920 x 1080 Screen Size 13.3' Refresh Rate 60 Hz Contrast 800:1 Brightness 300 nit Screen Type TFT IPS LCD Backlight LED Backlight Color Gamut 16.7M, NTSC 72%, sRGB up to 100% Speaker Double Speaker Viewing Angle 178 ° Aspect Ratio 16:9 Power Supply 5 - 20 V or Type-C USB 3.0 Inputs Mini HDMI, Type-C, Voltage Input Outputs 3.5 mm Jack Plug Operating Temperature 0 °C - 50°C Case Aluminum Alloy Dimensions 313 mm x 198 mm x 10 mm Weight 1010 g Included Joy-View 13 Display Smart Case 1.5m HDMI to mini-HDMI cable 1m Type-C to Type-C cable 1m USB-A to USB-C cable Power Adapter HDMI to mini -DMI adapter Cleaning Towel

Lees meer minder

De Picoboy is een krachtige mini handheld van slechts 3 x 5 cm. Hij is geschikt om te leren programmeren, je eigen games te ontwikkelen, of er gewoon mee te spelen. Ook is er een introductie tot het programmeren met de Arduino IDE en MicroPython beschikbaar. Het enige wat je nodig hebt is een PC, de PicoBoy en een USB-C kabel. Omdat de PicoBoy compatibel is met de Raspberry Pi Pico en de Arduino IDE zijn er talloze andere tutorials, voorbeelden en libraries op internet te vinden om het programmeren gemakkelijker te maken. Specificaties 1,3" OLED-display met 128 x 64 pixels (zwart/wit) RP2040 microcontroller, die hem compatibel maakt met de Raspberry Pi Pico 2x 133MHz ARM M0+ 2 MB Flash 264 KB RAM USB-C aansluiting voor programmering en gegevensoverdracht 3 vooraf geïnstalleerde games 5-voudige joystick Acceleration sensor (nu ook te gebruiken in Python!) Voeding via USB-C of een CR2032 knoopcel Afmetingen: 49,2 x 29,1 x 14,5 mm Downloads GitHub

Lees meer minder

Grove LED Bar is comprised of a 10 segment LED gauge bar and an MY9221 LED controlling chip. It can be used as a indicator for remaining battery life, voltage, water level, music volume or other values that require a gradient display.There are 10 LED bars in the LED bar graph: one red, one yellow, one light green, and the rest green. Demo code is available to get you up and running quickly. It lights up the LEDs sequentially from red to green, so the entire bar graph is lit up in the end. Want to go further? Go ahead and code your own effect!Features Each LED segment can be controlled individually via code Grove module Plug-and-play Can be cascaded for a larger display Flexible power option, supports 3-5.5 DC Available demo code Dimensions: 40 x 20 x 18 mm Included 1x Grove LED Bar v2.0 1x Grove Cable Downloads Grove LED Bar Eagle File Grove LED Bar Library MY9221 Datasheet Suli-compatible Library GitHub repository for LED Bar 10 Segment LED Gauge Bar

Lees meer minder

This ESP32 S3 7-inch IPS 5-point capacitive touch display with an ultra-high resolution of 1024 x 600 pixels is ideal for IoT applications. It is ideal for applications such as home automation. An integrated SD card enables recording/playback of stored data. There are also two Mabee/Grove connectors to connect various sensors to this board to create personal prototype projects in no time. Specifications Controller: ESP32-S3-WROOM-1, PCB antenna, 16 MB Flash, 8 MB PSRAM, ESP32-S3-WROOM-1-N16R8 Wireless: Wifi & Bluetooth 5.0 LCD: 7-inch High Lightness IPS FPS: >30 Resolution: 1024 x 600 LCD interface: RGB 565 Touch panel: Capacitive 5-point touch Touch panel driver: GT911 USB: Dual USB-C (one for USB-to-UART and one for native USB) UART to UART chip: CP2104 Power supply: USB-C 5.0 V (4.0 V~5.25 V) Button: Flash button and reset button Mabee interface: 1x I²C, 1x GPIO MicroSD: Yes Arduino support: Yes Type-C Power Delivery: Not supported Operation temperature: ?40 to +85°C Downloads Wiki GitHub ESP32-S3 Datasheet Screen touch coordinates calibration

Lees meer minder

Subtle diffusion makes the pixels extra-shiny by blurring the gaps. This improvement is obtained with a diffuser secured slightly away from the HAT. Unicorn HAT was hailed by raspberrypi.org for its versatility and row power with a score of 5/5! Features 256 RGB LED pixels in a 16x16 matrix Pixels driven by ARM STM32F and three STP16CPC26 LED drivers Bundled ninja diffuser (with nuts and bolts) Compatible with Raspberry Pi 3, 2, B+, A+, Zero, and Zero W Comes fully assembled

Lees meer minder

This 10.1-inch HDMI touch screen has a high-definition resolution of 1280x800 and supports a viewing angle of 178°, providing an excellent visual experience. It supports Raspberry Pi, Windows, Linux, Ubuntu and other systems, and is also compatible with Raspberry Pi 3/3B+/4B/5, Jetson Nano, Beaglebone, Banana Pi and other mainstream development boards. You can easily adjust the desired brightness by adjusting the backlight button. This Raspberry Pi capacitive touch screen supports 5-point touch, has fast response speed, and high-definition communication supports plug-and-play.It comes with a stand for easy desktop placement, and mounting holes on the back allow you to securely mount it on a wall or integrate it with a small form factor SBC (single board computer). To protect the screen and enhance its visual appeal, the monitor comes with a durable and stylish acrylic cover. Whether you need a high-quality monitor for gaming, multimedia entertainment, or industrial applications, our 10-inch monitors offer superior visuals, responsive touch controls, seamless connectivity, and versatile mounting options. Features IPS HD 1280x800 resolution and 178° full viewing angle offers crystal clear visuals and vivid colors for high-quality visual experience Support backlight control, itcan be adjusted by button Support capacitive 5-point touch, enable smooth, accurate and fast response Use HD communication, plug and play, and easy to use Support Windows, Linux, Ubuntu, Kodi, etc. Compatible with Raspberry Pi 3/3B+/4B/5, Jetson Nano, Beaglebone Specifications Screen Size 10.1 inch Screen Type IPS screen Resolution 1280 x 800 Backlight adjustment Key switch adjustment Touch Screen Type Capacitive Touch Screen Touch IC SIS9200 Power Micro-USB (5 V) Overall power 5.2942 W (100% brightness) Video Input Interface HDMI-Compatible (up to 1080p) Active Area 216.6 x 135.4 mm Dimensions (L x W x H) 239.4 x 157.4 x 12.3 ±0.2 mm Included 1x 10.1 inch Touch Display 1x HD to HD Cable 2x USB cable 1x HD to Mini HD Adapter 1x Screw Pack 2x Bracket 1x Screwdriver 1x Manual Downloads Manual Wiki

Lees meer minder

The Ardi Display Shield features a vibrant 2" IPS screen with a resolution of 240 x 320 pixels, providing sharp and crisp visuals for your projects. Whether you're working on a small-scale project or a complex prototype, this display shield ensures clear and vibrant display output. With 2 programmable buttons, you have the flexibility to create interactive experiences and user-friendly interfaces. Customize the buttons to trigger specific actions or navigate through menus effortlessly. The possibilities are endless, limited only by your imagination. In addition to the programmable buttons, the Ardi Display Shield also includes a 5-way joystick for intuitive control. With the joystick's SPI interface, you can easily navigate menus, scroll through options, and control various aspects of your Arduino project with precision and ease. Designed with compatibility and ease of use in mind, the Ardi Display Shield seamlessly integrates with the Arduino Uno board. Simply connect it to your Arduino Uno and unlock a world of possibilities for visual feedback, user interaction, and data visualization. Features Onboard 2.0" TFT Display Compatible with 3.3 V/5 V MCU, Selection provided Onboard 5-Way Joystick allows better control-related projects Two programmable Buttons to add additional functionality to project Mounts directly onto ArdiPi, Ardi32 or other Arduino compatible boards Specifications Display resolution: 240x320 pixels Pixel Pitch: 0.1275 x 0.1275 mm Active Area: 30.6 x 40.8 mm Module Size: 34.6 x 47.8 x 2.05 mm SPI Interface Display Colors: 65K colors Drive IC: ST7789V2 Viewing Direction: All-view the best image

Lees meer minder

CrowVision 11.6-inch touch screen is designed for all-in-one machines. It features a 1366 x 768 high-resolution screen and IPS panel, providing a superior visual experience. The industrial design-style rear-fixed metal structure is compatible with various single-board computers (SBCs), with a reasonable layout and neat wiring, making it easy to power up and use with simple operations. The screen uses HDMI-compatible communication and supports capacitive multi-touch. It has reserved interfaces and buttons for speakers and other accessories, making it adaptable to different usage scenarios. It can be used with a variety of commonly available single-board computers such as Raspberry Pi, Jetson Nano, and is plug-and-play, while also being fully compatible with the operating systems of single-board computers (such as Raspbian, Ubuntu, Windows, Android, Mac OS, and Chrome OS, etc.). This screen can be widely used in automation application control system displays, personal DIY projects, secondary screen/second window displays, single-board computer audio-video display equipment, HDMI communication devices, game console expansion screens, and other scenarios. Features 11.6-inch high-resolution screen with 1366 x 768 resolution, IPS panel, and 178° wide viewing angle provides a better visual experience Unique rear fixing structure with sliding fixing pillars, compatible with most single-board computer models, easy to assemble Wide compatibility, compatible with multiple operating systems (Raspbian, Ubuntu, Windows, Android, Mac OS, and Chrome OS) Supports audio, video, and capacitive touch, plug and play Integrates a variety of peripheral interfaces (such as speakers, headphones, keypads, touchscreens) and onboard OSD adjustment keys The mainboard is equipped with power conversion function of output 5 V/3 A, not need to separately connect an external power supply for the single-board computer. Specifications Display size: 11.6 inch Touch type: 5-point Capacitive Touch Resolution: 1366 x 768 Color depth: 16M Viewing angle: 178° wide viewing angle Display type: IPS Panel Screen type: TFT-LCD External power supply: 12 V/2 A Digital input: HDMI-compatible interface Interfaces: 1x Keypad interface, 1x power supply 5 V output, 1x Mini HD interface, 1x touch interface, 1x speaker interface, 1x headphone socket, 1x power supply 12 V input Compatibility system: Raspbian, Ubuntu, Windows, Android, Mac OS, and Chrome OS, etc. Active Area: 256.13 x 144 mm Dimensions: 290.8 x 184.2 mm Included 1x 11.6-inch capacitive touch ccreen 1x USB-A to USB-C cable 1x USB-A to micro B cable 1x HD to mini HD cable 1x Micro HD to mini HD cable 1x OSD control board 1x Power adapter 1x Screwdriver 2x Ribbon 1x Manual Downloads Manual Wiki

Lees meer minder

This 5.83-inch 3-color e-paper e-ink display module for Raspberry Pi Pico offers a resolution of 648 × 480 pixels, an SPI interface, low power consumption, wide viewing angle and a paper-like effect without electricity. Features No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing SPI interface, requires minimal I/O pins 2x user buttons and 1x reset button for easy interacting Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 3.3 V Display color Red, black, white Resolution 648 × 480 pixels Gray scale 2 Interface 3-wire SPI, 4-wire SPI Viewing angle >170° Partial refresh time N/A Full refresh time 5s Outline dimensions 125.4 × 99.5 mm Display size 119.232 × 88.320 mm Refresh power 26.4 mW (typ.) Standby current <0.01 uA (almost none) Dot pitch 0.184 × 0.184 mm Applications Suitable For Price Tags Asset/Equipment Tags Shelf Labels Conference Name Tag Included 1x 5.83-inch e-Paper (B) 1x Pico-ePaper-Driver-Board 1x Standoff pack Downloads Wiki

Lees meer minder