Producten

The Pico-10DOF-IMU is an IMU sensor expansion module specialized for Raspberry Pi Pico. It incorporates sensors including gyroscope, accelerometer, magnetometer, baroceptor, and uses I²C bus for communication. Combined with the Raspberry Pi Pico, it can be used to collect environment sensing data like temperature and barometric pressure, or to easily DIY a robot that detects motion gesture and orientation. Features Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series Onboard ICM20948 (3-axis gyroscope, 3-axis accelerometer, and 3-axis magnetometer) for detecting motion gesture, orientation, and magnetic field Onboard LPS22HB barometric pressure sensor, for sensing the atmospheric pressure of the environment Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 5 V Accelerometer Resolution: 16-bitMeasuring range (configurable): ±2, ±4, ±8, ±16gOperating current: 68.9uA Gyroscope Resolution: 16-bitMeasuring range (configurable): ±250, ±500, ±1000, ±2000°/secOperating current: 1.23mA Magnetometer Resolution: 16-bitMeasuring range: ±4900µTOperating current: 90uA Baroceptor Measuring range: 260 ~ 1260hPaMeasuring accuracy (ordinary temperature): ±0.025hPaMeasuring speed: 1Hz - 75Hz

Lees meer minder

Features 2.13' capacitive touch e-Paper display, 5-point touch, 250×122 pixels Supports waken up by user-defined gesture No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi Zero / Zero W Comes with development resources and manual (examples for Raspberry Pi) Included 1x 2.13inch Touch e-Paper HAT 1x ABS case 1x Screwdriver 1x Thermal tape 1x Rubber feet 4pcs 2x Screws Downloads Documentation

Lees meer minder

Features Adopts both 4-wire SPI and I²C interface, better compatibility, fast data rate Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Logical voltage 3.3 V Viewing angle >160° Operating voltage 3.3 V/5 V Resolution 128×32 pixels Communication interface 4-wire SPI, I²C Display size 55.02 × 13.10 mm Display panel OLED Pixel size 0.41 × 0.39 mm Driver SSD1305 Dimensions 63.00 × 26.00 mm

Lees meer minder

Features No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing SPI interface, requires minimal IO pins Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 3.3 V Display color red, black, white Interface 3-wire SPI, 4-wire SPI Grey scale 2 Outline dimensions 74.00 × 37.5 0mm Full refresh time 15s Display size 60.088 × 30.704 mm Refresh power 42.4 mW (typ.) Dot pitch 0.203 × 0.202 mm Standby current <0.01 uA (almost none) Resolution 296×152 pixels Viewing angle >170° Downloads Wiki

Lees meer minder

Features No backlight Displays last images even when powered down Ultra low power consumption SPI interface Compatible with 3.3 V and 5 V Specifications Operating voltage 3.3 V / 5 V Interface 3-wire SPI, 4-wire SPI Outline dimension 89.5 x 38 mm Display size 66.89 x 29.05 mm Dot pitch 0.138 x 0.138 Resolution 296 x 128 Display color red, black, white Grey level 2 Full refresh time 15 s Refresh power 26.4 mW Standby power <0.017 mW Viewing angle >170° For more information check out the waveshare wiki here.

Lees meer minder

Features 480 x 320 resolution, IPS screen, 65K colors, clear and colorful displaying effect Dedicated touch controller, bringing more smooth touching effect than AD-controlled solutions MicroSD card slot for storing images and direct displaying them easily Programmable backlight control, power saving Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 5 V Resolution 480 x 320 pixels Communication interface SPI Display size 73.44 x 48.96 mm Display panel IPS Pixel size 0.153 x 0.153 mm Driver ILI9488 Dimensions 86.00 x 57.20 mm Touch controller XPT2046 DownloadsWiki

Lees meer minder

Features SPI-compatible, easy to drive Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 5 V Digits 4 Dispaly size 0.4 inch LED color red Driver 74HC595 Display part no. FJ4401AH Dimensions 52 × 21 mm

Lees meer minder

Features Advanced Color ePaper (ACeP) technologie, ondersteunt 7-kleuren display Geen achtergrondverlichting, blijft de laatste inhoud weergeven voor een lange tijd, zelfs als de stroom uitgeschakeld is Ultra laag stroomverbruik, in principe is alleen stroom nodig voor het verversen SPI-interface, voor aansluiting met controller boards zoals Raspberry Pi/Jetson Nano/Arduino/STM32, enz. Onboard voltage vertaler, compatibel met 3.3 V / 5 V MCUs Wordt geleverd met ontwikkelingshulpmiddelen en handleiding (voorbeelden voor Raspberry Pi/Jetson Nano/Arduino/STM32) Specificaties Bedrijfsspanning 3,3 V/5 V Display kleur ACeP 7-kleuren Interface 3-draads SPI, 4-draads SPI Grijze schaal 2 Outline afmetingen 138,5 × 100,5 mm Volledige verversingstijd <35s Display-formaat 114,9 × 85,8 mm Versieuwingsvermogen 50 mW (nom.) Dot pitch 0,1915 × 0,1915 mm Stand-by tijd <0.01 uA (bijna geen) Resolutie 600 × 448 pixels Zichthoek >170° Downloads Wiki

Lees meer minder

This 5.83-inch 3-color e-paper e-ink display module for Raspberry Pi Pico offers a resolution of 648 × 480 pixels, an SPI interface, low power consumption, wide viewing angle and a paper-like effect without electricity. Features No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing SPI interface, requires minimal I/O pins 2x user buttons and 1x reset button for easy interacting Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 3.3 V Display color Red, black, white Resolution 648 × 480 pixels Gray scale 2 Interface 3-wire SPI, 4-wire SPI Viewing angle >170° Partial refresh time N/A Full refresh time 5s Outline dimensions 125.4 × 99.5 mm Display size 119.232 × 88.320 mm Refresh power 26.4 mW (typ.) Standby current <0.01 uA (almost none) Dot pitch 0.184 × 0.184 mm Applications Suitable For Price Tags Asset/Equipment Tags Shelf Labels Conference Name Tag Included 1x 5.83-inch e-Paper (B) 1x Pico-ePaper-Driver-Board 1x Standoff pack Downloads Wiki

Lees meer minder

This 5.83-inch black/white e-paper e-ink display module for Raspberry Pi Pico offers a resolution of 648 × 480 pixels, an SPI interface, low power consumption, wide viewing angle and a paper-like effect without electricity. Features No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing SPI interface, requires minimal I/O pins 2x user buttons and 1x reset button for easy interacting Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 3.3 V Display color Black, white Resolution 648 × 480 pixels Gray scale 2 Interface 3-wire SPI, 4-wire SPI Viewing angle >170° Partial refresh time N/A Full refresh time 5s Outline dimensions 125.4 × 99.5 mm Display size 119.232 × 88.320 mm Refresh power 26.4 mW (typ.) Standby current <0.01 uA (almost none) Dot pitch 0.184 × 0.184 mm Applications Suitable For Price Tags Asset/Equipment Tags Shelf Labels Conference Name Tag Included 1x 5.83-inch e-Paper 1x Pico-ePaper-Driver-Board 1x Standoff pack Downloads Wiki

Lees meer minder

The Zero-DISP-7A is a 7? touch display kit for Raspberry Pi Zero with IPS Display Expansion Board featuring 1024x600 pixels and 5-point capacitive touch. Features 7-inch IPS touch display with a hardware resolution of 1024x600. 5-point touch control, toughened glass panel with up to 6H hardness. When working with Raspberry Pi Zero, supports Raspberry Pi OS, Ubuntu, Kali, and Retropie systems. Onboard ETH/USB HUB function, adapting RJ45 and USB port serving as an alii-in-one mini computer. Onboard 4-pin speaker header and 3.5 mm audio jack, support for HDMI audio output. Specifications Zero connectors Mini HDMI port, 2x USB Micro male port (1x HUB, 1x Power supply) Display 7-inch 1024 x 600 pixels, 5-point capacitive touch Networking 100M Ethernet RJ45 port USB 2x USB 2.0 port Audio Headphone jack, 4-pin speaker header Power input USB Type-C Interface, 5V Included 1x Zero-DISP-7A 1x Button board 1x Button board cable (9 cm) 4x White nylon spacer Downloads Wiki

Lees meer minder

This 7.5-inch e-paper E-Ink display HAT for Raspberry Pi with SPI interface provides low power consumption, wide viewing angle and a paper-like display of 3 colors (red, black, white) without electricity. Advantages Of E-Ink E-paper display utilizes microcapsule electrophoretic technology for displaying, the principle is: charged particles suspended in clear fluid will move to sides of microcapsule when electric field is applied, making the microcapsule become visible by reflecting ambient light, just as traditional printed paper. E-paper display will clearly display images/texts under lamplight or natural light, requires no backlight, and features nearly up to 180° viewing angle. It is usually used as e-reader due to its paper-like effect. Features No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing Standard Raspberry Pi 40-pin GPIO extension header, supports Raspberry Pi series boards, Jetson Nano SPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/STM32, etc. Onboard voltage translator, compatible with 3.3/5 V MCUs Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32) Specifications Operating voltage 3.3/5 V Interface 3-wire SPI, 4-wire SPI Display size 163.2 x 97.92 mm Dot pitch 0.205 x 0.204 mm Resolution 800 x 480 pixels Display color Red, black, white Viewing angle >170° Gray scale 2 Full refresh time 26s Refresh power 48mW (typ.) Standby current <0.01uA (almost none) Dimensions 170.2 x 111.2 mm Included 1x 7.5-inch e-Paper HAT (B) 1x RPi screws pack (2pcs) 1x GH1.25 9-pin cable (20 cm) Downloads Wiki (Manual)

Lees meer minder

This IPS 7.9-inch HDMI touch display with 400 x 1280 resolution, 170° wide viewing angle and built-in ferrite Hi-Fi speaker can be used as a secondary screen for chassis and also supports Raspberry Pi and Jetson Nano. Features 7.9-inch IPS display with a hardware resolution of 400 x 1280. Zinc alloy case, toughened glass panel with up to 6H hardness. When working as a computer monitor, it supports Windows without a driver. When working with Raspberry Pi, it supports Raspberry Pi OS / Ubuntu / Kali and Retropie, driver-free. When working with Jetson Nano, it supports Ubuntu, driver-free. Support backlight control for power saving. Support 5-point capacitive touch control. Specifications Display size 7.9" Viewing angle 170° Resolution 400 x 1280 pixels Display area 191.08 x 60.40 mm IPS version solor gamut 62% NTSC Max brightness 550 cd/m² Backlight adjustment Adjusted by the key/HID software Contrast 900:1 Color depth 16.7M Refresh rate 60 Hz Power port USB-C Display port HDMI interface Dimensions 211 x 73 x 20 mm Included 1x 7.9-inch Side Monitor 1x HDMI to Micro HDMI adapter 1x USB Type-A to Type-C cable (1 m) 1x HDMI flat cable (1 m) 2x Nonskid rubber feet Downloads Wiki

Lees meer minder

Waveshare Core3S500E is an FPGA core board that features an XC3S500E device onboard supporting further expansion. Features Onboard 1x XCF04S Integrated FPGA basic circuit, such as clock circuit Onboard nCONFIG button, RESET button, 4x LEDs All the I/O ports are accessible on the pin headers Onboard JTAG debugging/programming interface 2.0 mm header pitch design, suitable for being plugged-in your application system Downloads Wiki

Lees meer minder

Waveshare CoreEP4CE10 is an FPGA core board that features an EP4CE10F17C8N device onboard supporting further expansion. Features Onboard Serial Configuration Device EPCS16SI8N Integrated FPGA basic circuit, such as clock circuit Onboard nCONFIG button, RESET button, 4x LEDs All the I/O ports are accessible on the pin headers Onboard JTAG debugging/programming interface 2.00 mm header pitch design, suitable for being plugged-in your application system Downloads Wiki

Lees meer minder

Wveshare CoreEP4CE6 is an FPGA core board that features an EP4CE6E22C8N device onboard supporting further expansion. Features Onboard Serial Configuration Device EPCS16SI8N Integrated FPGA basic circuit, such as clock circuit Onboard nCONFIG button, RESET button, 4x LEDs All the I/O ports are accessible on the pin headers Onboard JTAG debugging/programming interface 2.54 mm header pitch design, suitable for being plugged-in your application system Downloads Wiki

Lees meer minder

Features Standard Raspberry Pi Pico female header for direct attaching Raspberry Pi Pico (if male header soldered), or just through jumper wires Two sets of 2x20 male header, allows connecting more Raspberry Pi Pico expansion modules Clear pinout labels on the front side, easy to use Immersion gold process, beautiful & practical, stunning aesthetic looking

Lees meer minder

Waveshare DVK600 is an FPGA CPLD mother board that features expansion connectors for connecting FPGA CPLD core board and accessory boards. DVK600 provides an easy way to set up FPGA CPLD development system. Features FPGA CPLD core board connector: for easily connecting core boards which integrate an FPGA CPLD chip onboard 8I/Os_1 interface, for connecting accessory boards/modules 8I/Os_2 interface, for connecting accessory boards/modules 16I/Os_1 interface, for connecting accessory boards/modules 16I/Os_2 interface, for connecting accessory boards/modules 32I/Os_1 interface, for connecting accessory boards/modules 32I/Os_2 interface, for connecting accessory boards/modules 32I/Os_3 interface, for connecting accessory boards/modules SDRAM interface for connecting SDRAM accessory board also works as FPGA CPLD pins expansion connectors LCD interface, for connecting LCD22, LCD12864, LCD1602 ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc. 5 V DC jack Joystick: five positions Buzzer Potentiometer: for LCD22 backlight adjustment, or LCD12864, LCD1602 contrast adjustment Power switch Buzzer jumper ONE-WIRE jumper Joystick jumper Downloads Schematics

Lees meer minder

The Pico-Clock-Green is an LED digits electronic clock designed for Raspberry Pi Pico. It incorporates high precision RTC chip DS3231, photosensor, buzzer, and buttons, features multiple functions including accurate electronic clock, temperature display, auto brightness adjustment, alarm, and button config. The important part is, rich open source codes and development tutorials are also provided to help you fast get started with Raspberry Pi Pico and make your own original electronic clock. Features Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series Onboard high precision RTC chip DS3231, with backup battery holder, maintains accurate timekeeping when main power is off Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year with Leap-Year Compensation Valid Up to 2100 Optional format: 24-hour OR 12-hour with an AM/PM indicator 2x programable alarm clock Digital temperature sensor output: ±3°C accuracy Embedded photosensor for auto brightness adjustment due to the ambient light, power saving and eye care Embedded buzzer for alarm or hourly ring, etc. 3x buttons for configuration Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Scrolling display Alarm/hourly ring Temperature in °F or °C format 12/24 time format Day of week auto adjustment Timekeeping without main power Timer configuration Manual/auto brightness adjustment Button configuration Program/debug port: USB Power supply: 5 V via USB connection Outline dimensions: 216 × 79 × 25 mm Display size: 190 × 60 mm LED digit: jade green Included 1x Pico-Clock-Green 1x Case 1x USB-A to micro-B cable 1.2 m 1x Button cell CR2032 1x Screws pack

Lees meer minder

The ETH-USB-Hub-Box is a Hub kit with ETH/USB Hub HAT (B) inside. It is tailored for Raspberry Pi Zero series, small in size, each cut-out of the case is exactly aligned with the connector. The case adopts classic Raspberry Pi red/white color combination, with quality dull polish surface, effectively keeping the Zero away from dust. This Hub Box will provide RJ45 Ethernet port and more USB capability for your Zero, make it easy to connect the Internet and sorts of USB devices. Features Designed for Raspberry Pi Zero, compatible with Zero series boards 3x extended USB ports, compatible with USB 2.0 / 1.1 Incorporates RTL8152B Ethernet chip, supports 1x RJ45 Ethernet port, 10/100M auto-negotiation Pogo pin design, for direct connecting with Raspberry Pi Zero/Zero W/Zero WH Angle rounded design, smooth hand feeling, 'simple snap' case lid Quality ABS material, dull polish surface, anti-fingerprint Comes with two different lids, changing as you like Included 1x ETH/USB Hub HAT (B) 1x ABS case 1x Rubber feet 4pcs 1x Screws pack 1x Screwdriver Downloads Documentation

Lees meer minder

The Pico-Eval-Board is an overall evaluation solution designed for Raspberry Pi Pico. With 3.5-inch 65K colorful LCD display and misc helpful onboard components, this evaluation board allows you to try almost every on chip peripheral of the RP2040, eliminating the mess wiring. It is an ideal choice for user to fast get started with the Raspberry Pi Pico, as well as the RP2040 chip. Features Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards 3.5-inch resistive touch screen, 65K colorful, bringing clear and vivid display effect Standard 3.5 mm audio jack, for headphone or other audio peripherals Micro SD card slot through the SDIO interface, faster access speed than SPI interface Integrates battery header and recharge circuit, allows it keep running without wired power supply Other rich resources like buzzer, photoresistor, and RGB LED... Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) LCD Specifications Operating voltage 5 V Resolution 480×320 Pixels Touch type resistive Display colors 65K colorful Communication bus SPI Display size 73.44 × 48.96 mm Display panel IPS Pixel size 0.153 × 0.153 mm Controller ILI9488/XPT2046 Dimension 86.00 × 57.20 mm

Lees meer minder

This Industrial 6-Channel Relay Module is suitable for Raspberry Pi Zero with pre-soldered pinheader. It provides RS485/CAN Bus, Power Supply Isolation, and Photocoupler Isolation.Features RS485 half-duplex communication: using SP3485, UART control, auto RX/TX switch CAN half-duplex communication: using MCP2515 + SN65HVD230 solution, SPI control Onboard unibody power supply isolation, provides stable isolated voltage, needs no extra power supply for the isolated terminal Onboard photocoupler isolation, prevent interference from external high-voltage circuit connected to the relay Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightningproof & anti-electrostatic Onboard resettable fuses and protection diodes, ensuring current/voltage stable output, preventing over current/voltage, better shock-resistance performance High quality relay, contact rating: ?10A 250V AC or ?10A 30V DC ABS protection enclosure with rail-mount support, easy to install, safe to use Comes with development resources and manual (wiringPi and python examples) Specifications Operating voltage: 7~36 V (industrial input voltage compatible) Relay channel: 6ch Communication Protocol: RS485, CAN Contact form: 1NO 1NC Included 1x ABS protection enclosure (top and bottom) 1x RPi Zero Relay 1x Screwdriver 1x OPTIONS 12 V, 1 A power adapter 1x Screws pack DownloadsDocumentation

Lees meer minder

De USB-CAN-FD is een hoogwaardige industriële USB-naar-CAN-FD-adapter, CAN/CAN-FD bus communicatie-interfacekaart en CAN/CAN-FD protocoldata analysator. Aan boord dubbele onafhankelijke CAN-FD interfaces met elektrische isolatie en meerdere beveiligingscircuits. Ondersteunt Windows, wordt geleverd met stuurprogramma's, CAN-FD Tools gerelateerde software, secundaire ontwikkelingsvoorbeelden en tutorials.Het kan via een USB-poort worden aangesloten op een pc of industriële besturingshost om transceiverbesturing, gegevensanalyse, verzameling en bewaking van CAN/CAN-FD-busnetwerk te realiseren. Het apparaat is compact en gebruiksvriendelijk en kan worden gebruikt voor het leren en debuggen van de CAN/CAN-FD-bus en voor secundaire ontwikkeling en integratie in diverse industriële, energiecommunicatie- en intelligente besturingstoepassingen die CAN/CAN-FD-bus communicatie vereisen.Specificaties Soort product Industriële kwaliteit: USB naar CAN-FD interfaceconverter, CAN/CAN-FD bus communicatie-interfacekaart, CAN/CAN-FD protocoldata analysator USB Bedrijfsspanning 5 V (rechtstreeks van de USB-poort zonder externe voeding) Aansluiting USB-B CAN/CAN FD-interface CAN/CAN FD-kanaal Tweekanaals: CAN1 en CAN2 (onafhankelijk en volledig geïsoleerd, isolatie spanning: 3000 V DC) Aansluiting CAN-bus schroefklem (OPEN6 5,08 mm steek) Afsluitweerstand Elk CAN/CAN-FD-kanaal heeft twee ingebouwde 120? afsluitweerstanden, die kunnen worden ingeschakeld met een schakelaar Baudrate 100Kbps~5Mbps (configureerbaar via software) Protocol ondersteuning CAN2.0A, CAN2.0B en ISO 11898-1 CAN-FD protocol V.1.0 Overdrachtssnelheid De ontvangst- en verzendsnelheid van elk CAN/CAN-FD-kanaal kan 20000 frames/s en 5000 frames/s bereiken. Buffer voor verzenden 1500 frames ontvangstbuffer en 64 frames zendbuffer per kanaal (automatisch opnieuw zenden als de verzending mislukt) Indicatoren PWR Voedingsspanning SYS Systeemstatus, normaal uit; blijft aan als er een bus fout is CAN1 CAN1-kanaalindicator (knippert bij verzenden en ontvangen van data) CAN2 CAN2-kanaalindicator (knippert bij verzenden en ontvangen van data) Systeemondersteuning Windows Windows XP/7/8/10/11 (32/64 bits); biedt nog geen ondersteuning voor Linux; de bijbehorende stuurprogramma's zijn in ontwikkeling. Bedrijfstemperatuur ?40 tot +85°C Materiaal behuizing Aluminium behuizing + 3D vlamwerende isolatieplaten aan beide zijden (Dit ontwerp kan een betere bescherming bieden tegen elektrische ontladingen, verbetert de veiligheid van het product en verlengt de levensduur) Afmetingen 104 x 70 x 25 mm Inbegrepen Waveshare USB-CAN-FD USB-A naar USB-B kabel 4-pins kabel Schroevendraaier DownloadsWiki

Lees meer minder

The Waveshare Jetson Nano Development Kit, based on AI computers Jetson Nano (with 16 GB eMMC) and Jetson Xavier NX, provides almost the same IOs, size, and thickness as the Jetson Nano Developer Kit (B01), more convenient for upgrading the core module. By utilizing the power of the core module, it is qualified for fields like image classification, object detection, segmentation, speech processing, etc., and can be used in sorts of AI projects. Specifications GPU 128-core Maxwell CPU Quad-core ARM A57 @ 1.43 GHz RAM 4 GB 64-bit LPDDR4 25.6 GB/s Storage 16 GB eMMC + 64 GB TF Card Video encoder 250 MP/s 1x 4K @ 30 (HEVC) 2x 1080p @ 60 (HEVC) 4x 1080p @ 30 (HEVC) Video decoder 500 MP/s 1x 4K @ 60 (HEVC) 2x 4K @ 30 (HEVC) 4x 1080p @ 60 (HEVC) 8x 1080p @ 30 (HEVC) Camera 1x MIPI CSI-2 D-PHY lanes Connectivity Gigabit Ethernet, M.2 Key E expansion connector Display HDMI USB 1x USB 3.2 Gen 1 Type A 2x USB 2.0 Type A 1x USB 2.0 Micro-B Interfaces GPIO, I²C, I²S, SPI, UART Dimensions 100 x 80 x 29 mm Included 1x JETSON-NANO-LITE-DEV-KIT (carrier + Nano + heatsink) 1x AC8265 dual-mode NIC 1x Cooling fan 1x USB cable (1.2 m) 1x Ethernet cable (1.5 m) 1x 5 V/3 A power adapter (EU) 1x 64 GB TF Card 1x Card reader Documentation Wiki

Lees meer minder