Zoekresultaten voor "texas-instruments"
IQaudIO Pi-DAC+ (for Raspberry Pi)
IQaudio DAC+ is an audio output HAT for all generations of Raspberry Pi from Raspberry Pi1 Model B+ onwards, and supports 24?bit 192 kHz high-resolution digital audio. It uses the Texas Instruments PCM5122 DAC to deliver stereo analogue audio to a pair of phono connectors, and also supports a dedicated headphone amplifier.
€ 29,95
Leden € 26,96
MSP430 Microcontroller Essentials
De MSP430 is een populaire familie van microcontrollers van Texas Instruments. In dit boek zullen we werken met het kleinste type, namelijk de krachtige MSP430G2553. We zullen de mogelijkheden van deze microcontroller in detail bekijken, omdat hij zeer geschikt is voor zelfbouwprojecten omdat hij beschikbaar is in een P-DIP20 pakket.We zullen de microcontroller nader bekijken en vervolgens stap voor stap een aantal interessante applicaties bouwen, waaronder een 'Hello World' knipperende LED en een leuke klok applicatie, die de dag van de week kan berekenen op basis van de datum.Je leert ook hoe je code maakt voor de MSP microcontroller in assembler. Daarnaast wordt er gewerkt met de MSP-Arduino IDE, die het vrij eenvoudig maakt om snelle applicaties te maken zonder speciale diepgaande kennis van de microcontrollers.Alle code die in het boek wordt gebruikt, kan worden gedownload van de Elektor-website.
€ 34,95€ 19,95
Leden identiek
Elektor Digital MSP430 Microcontroller Essentials (E-book)
De MSP430 is een populaire familie van microcontrollers van Texas Instruments. In dit boek zullen we werken met het kleinste type, namelijk de krachtige MSP430G2553. We zullen de mogelijkheden van deze microcontroller in detail bekijken, omdat hij zeer geschikt is voor zelfbouwprojecten omdat hij beschikbaar is in een P-DIP20 pakket.We zullen de microcontroller nader bekijken en vervolgens stap voor stap een aantal interessante applicaties bouwen, waaronder een 'Hello World' knipperende LED en een leuke klok applicatie, die de dag van de week kan berekenen op basis van de datum.Je leert ook hoe je code maakt voor de MSP microcontroller in assembler. Daarnaast wordt er gewerkt met de MSP-Arduino IDE, die het vrij eenvoudig maakt om snelle applicaties te maken zonder speciale diepgaande kennis van de microcontrollers.Alle code die in het boek wordt gebruikt, kan worden gedownload van de Elektor-website.
€ 29,95
Leden € 23,96
Elektor Labs Elektor Raspberry Pi Buffer Board
When you experiment with the Raspberry Pi on a regular basis and you connect a variety of external hardware to the GPIO port via the header you may well have caused some damage in the past. The Raspberry Pi Buffer Board is there to prevent this! The board is compatible with Raspberry Pi Zero, 3, 4, 5 and 400. All 26 GPIOs are buffered with bi-directional voltage translators to protect the Raspberry Pi when experimenting with new circuits. The PCB is intended to be inserted in the back of Raspberry Pi< 400. The connector to connect to the Raspberry Pi is a right angled 40-way receptacle (2x20). The PCB is only a fraction wider. A 40-way flat cable with appropriate 2x20 headers can be connected to the buffer output header to experiment for instance with a circuit on a breadboard or PCB. The circuit uses four TXS0108E ICs by Texas Instruments. The PCB can also be put upright on a Raspberry Pi 3 or newer. Downloads Schematics Layout
€ 29,95€ 22,95
Leden € 20,66
Elektor Digital Das MSP430 Mikrocontroller Buch (E-book)
Das MSP430 Mikrocontroller Buch (E-book)
€ 34,80
Leden € 27,84
SparkFun SparkFun Qwiic GPIO
De Sparkfun Qwiic GPIO is een I²C uitbreidingsbord met de TCA9534 I/O Expander IC van Texas Instruments. Dit bord voegt acht IO-pinnen toe die u net als elke andere digitale pin van uw microcontroller kunt lezen en schrijven. De besturing via de I²C interface wordt verzorgd door een Arduino-bibliotheek, zodat u eenvoudig functies kunt aanroepen vergelijkbaar met Arduino's pinMode en digitalWrite om deze extra I/O's aan te sturen. De pinnen van de TCA9534 bereikbaar via gebruikersvriendelijke aansluitklemmen; er is geen schroevendraaier nodig om draden aan te sluiten! De aansluitklemmen zijn relatief groot, waardoor het mogelijk is meerdere draden in een ground- of power-aansluitng te combineren. Met drie aanpasbare adres-jumpers, kunt u tot acht Qwiic GPIO borden aansluiten op een enkele bus, waarmee u over 64 extra GPIO pinnen beschikt! Het standaard I²C-ades is 0x27 en kan worden gewijzigd door het aanpassen van de jumpers op de achterkant van het bord. Eigenschappen Acht configureerbare GPIO-pennen I2C Adres: 0x27 (Standaard) Hardware jumpers maken tot acht borden op een enkele bus mogelijk Input Polarity Inversion Register Bestuur acht I/O pinnen individueel of tegelijk. Open-Drain Active-Low Interrupt Output 2 x Qwiic Connectors Afmetingen: 60,96 mm x 38,10 mm
€ 7,95
Leden € 7,16
Elektor Digital Audio 4 als PDF (DE)
Audio 4 als PDF (DE)
€ 16,90
Leden € 15,21
Great Scott Gadgets Great Scott Gadgets YARD Stick One - Sub-1 GHz Wireless Test Tool
YARD Stick One (Yet Another Radio Dongle) is a sub-1 GHz wireless transceiver IC on a USB dongle. It is based on the Texas Instruments CC1111. YARD Stick One can transmit or receive digital wireless signals at frequencies below 1 GHz. It uses the same radio circuit as the popular IM-Me. The radio functions that are possible by customizing IM-Me firmware are now at your fingertips when you attach YARD Stick One to a computer via USB. Features Half-duplex transmit and receive Official operating frequencies: 300-348 MHz, 391-464 MHz, and 782-928 MHz Unofficial operating frequencies: 281-361 MHz, 378-481 MHz, and 749-962 MHz Modulations: ASK, OOK, GFSK, 2-FSK, 4-FSK, MSK Data rates up to 500 kbps Full-Speed USB 2.0 SMA female antenna connector (50 ohms) Software-controlled antenna port power (max 50 mA at 3.3 V) Low pass filter for elimination of harmonics when operating in the 800 and 900 MHz bands GoodFET-compatible expansion and programming header GIMME-compatible programming test points Open source Downloads Documentation GitHub
€ 99,95
Leden € 89,96
Elektor Labs DIY LiPo Supercharger Kit V2 (by GreatScott!)
This DIY LiPo Supercharger/Booster (developed the electronics engineer/YouTuber GreatScott! and produced by Elektor) can charge a single-cell LiPo battery and protect it against the effects of overvoltage, overload, and short-circuits. Additionally, it can boost the battery voltage to 5 V or 12 V. The boosted output voltage is protected by an ‘eFuse’ IC outputting 1.52 A at 5 V or 0.76 A at 12 V maximum.The charger part of the circuit needs a +5 V power supply which can be connected through USB-C, or simply two wires soldered to pads on the PCB.In addition, other connections can be soldered to pads on the PCB or by using single pinheaders.Included 1x Mainboard pre-assembled with the 4 ICs 15x Resistors 3x LEDs 13x Capacitors 2x Switches 1x USB-C on a breakout board 2x Diodes Please note: Battery is not included.The board uses a DC/DC Converter, an IC charger, and an e Fuse from Texas Instruments. The battery protection IC is from Xysemi and provides under-voltage lockout, over current protection, and reverse battery protection.The board is connected to the power and recharges the batteries via a USB-C connection.Specifications Battery Single-cell lithium-ion or lithium-polymer battery Input Voltage +5 V / 2 A max. Output Voltage 5 V / 1.52 A12 V / 0.76 A LiPo Protection XB8089D Overcharge Detection 4.250 V Overcharge Release 4.10 V Overdischarge Detection 2.50 V Overdischarge Release 3 V Overcurrent Detection 10.0 A Thermal Shutdown Auto-retry Enable/Undervoltage Lockout Rising: 1.2 V (typ.)Falling: 1.1 V (typ.)
€ 29,95€ 24,95
Leden identiek
Elektor Bundles Raspberry Pi Bundel: Zero W + Buffer Board (+ GRATIS Special)
Het Raspberry Pi and Pico Special (t.w.v. € 15) wordt automatisch aan uw winkelwagen toegevoegd! Deze bundel bevat de Raspberry Pi Zero W en het Elektor Raspberry Pi Buffer Board. Raspberry Pi Zero W De Raspberry Pi Zero W is de nieuwste telg van de Raspberry Pi Zero-familie. De Raspberry Pi Zero W heeft alle functionaliteit van de originele Raspberry Pi Zero, maar wordt geleverd met toegevoegde connectiviteit bestaande uit: 802.11 b/g/n WLAN Bluetooth 4.1 Bluetooth Low Energy (BLE) Overige kenmerken 1 GHz, single-core CPU 512 MB RAM Mini HDMI en USB On-The-Go poorten Micro-USB voeding HAT-compatibele 40-pins header Composiet video en reset headers CSI-camera-aansluiting Downloads Mechanische tekening Schema's Elektor Raspberry Pi Buffer Board When you experiment with the Raspberry Pi on a regular basis and you connect a variety of external hardware to the GPIO port via the header you may well have caused some damage in the past. The Raspberry Pi Buffer Board is there to prevent this! The board is compatible with Raspberry Pi Zero, 3, 4, 5 and 400. All 26 GPIOs are buffered with bi-directional voltage translators to protect the Raspberry Pi when experimenting with new circuits. The PCB is intended to be inserted in the back of Raspberry Pi< 400. The connector to connect to the Raspberry Pi is a right angled 40-way receptacle (2x20). The PCB is only a fraction wider. A 40-way flat cable with appropriate 2x20 headers can be connected to the buffer output header to experiment for instance with a circuit on a breadboard or PCB. The circuit uses four TXS0108E ICs by Texas Instruments. The PCB can also be put upright on a Raspberry Pi 3 or newer. Downloads Schematics Layout
€ 64,95€ 49,95
Leden identiek
IQaudIO DAC Pro (for Raspberry Pi)
IQaudio DAC Pro is our highest-fidelity audio output HAT. It uses the Texas Instruments PCM5242 DAC to deliver outstanding signal-to-noise ratio performance from a Raspberry Pi 1 Model B+, 2, 3, and 4, and supports balanced/differential output in parallel to phono/RCA line level output. It also includes a dedicated headphone amplifier.