Zoekresultaten voor "USB la"
LabNation LabNation SmartScope USB-oscilloscoop
Smartscope is de enige scoop ter wereld die werkt op alle belangrijke platforms: Windows, macOS, Linux, Android en iOS (met WiFi bridge). Sluit de SmartScope aan op vrijwel elk apparaat! Bovendien kunt u er mobiel mee werken: neem de SmartScope mee op pad, dankzij de connectiviteit met één kabel. Alles wordt intuïtief: aanwijzen, knijpen en vegen vervangt eindelijk de onhandige interfaces van oude scopes. Met de SmartScope ontwikkelt u uw digitale interfaces met behulp van de 100 MS/s logic analyzer. Met dit gereedschap kunt u elk gewenst signaal ontwerpen met behulp van Excel, en het vervolgens uploaden naar de ingebouwde Arbitrary Waveform Generator (AWG). Aan het eind legt u 100 miljoen keer per seconde de spanning vast op elk punt van uw ontwerp. De software voor de ondersteuning van Windows / macOS) / Linux / Android en exportformaten (Excel .csv / Matlab .mat) worden gegeven. Kenmerken Elk kanaal bemonsterd op 100 MHz/s AC/DC-koppeling op analoge ingangen 100% geruisloos 64 Mbit RAM: x10000 zoom Arbitraire golfvormgenerator 8 digitale ingangen bij 100 MS/s elk 4 digitale uitgangen van elk 100 MS/s Externe voeding voor het geval uw mobiel geen stroom kan leveren. Specificaties Oscilloscope Bandwidth 30 MHz (-3 dB point) Sample rate 2 x 100 MS/s Channels 2 Max pre-trigger position 16 x full scale Max post-trigger position Full scale Max full voltage scale 10 V/div (±35 V input range) Min full voltage scale 20 mV/div Analog input range -35 V, +35 V Max input peak-to-peak 40 V Signal coupling AC / DC Precision 8 bit Input impedance 1 M? // 10 pF Waverforms 200 waveforms/s Data delay to host < 10 ms Sample depth Up to 4 million samples per channel External trigger Yes Logic Analyzer Input channels 8 Input impedance 100 kOhm // 2 pF to GND Sample rate 100 MS/s Logic level 1.8 V to 5.0 V Diode protection Bidirectional Input data buffer 4 million samples Waverforms 200 waveforms/s Data delay to host < 10 ms Protocol decoders I²C, SPI, UART, I²S integrated User extensible Wave Generator (Analog Output) Output channels 1 Data rate Up to 50 MS/s Output level 0-3.3 V (Opamp driven) Output buffer Up to 2048 samples Max slew rate 30 ns/V Step 13 mV Wave Generator (Digital Output) Channels 4 Data rate Up to 100 MS/s Output level 3.3 V or 5 V (selectable) Output buffer Up to 2048 samples Diode protected Yes Programmable Logic USB controller MicroChip PIC18F14K50 USB interface PicKit3 or USB flashable FPGA Xilinx Spartan 6 FPGA interface JTAG and USB flashable Size & Weight Dimensions 110 x 64 x 24.2 mm (L x W x D) Weight 158 g Case Aluminium Connectivity Device/Host mini USB included Record waveforms Store Matlab (.mat) or Excel (.csv) files through Dropbox Analog BNC 2 probes included Digital 8 x 0.1' pitch, probes (included) Sync USB micro B-B Power USB micro B (optional) Inbegrepen 1x SmartScope USB-oscilloscoop 2x Analog probes 1x Digital probe kabels 1x Mini-B USB-kabel Downloads User manual Software GitHub Wiki
€ 239,00€ 149,95
Leden identiek
JOY-iT USB-A to Micro USB-B Cable with Switch
USB-A to Micro USB-B power cable (power supply only) 1.5 m length with ON/OFF switch Add the ability to control the power to your USB-powered project simply by plugging a cable with a switch between the USB power port and the USB cable. There's no more need to pull the cable to restart or reboot your devices, just press the button to turn on and off, which helps to prevent the USB connector from wear and tear due to frequent pulling and inserting the USB cable. It can be used as a power supply up to 2 A. Not applicable for data transfer.
€ 4,95
Leden € 4,46
Kuongshun USB-A to USB-C Cable with ON/OFF Switch
Features Type C cable USB type C is suitable for new version Raspberry Pi 4 No need to pull the cable to restart or reboot your Pi, just press the button to turn your Pi on and off Can be used as power supply for the Pi up to 2 Amp Help prevent the Pi's USB connector from wear and tear due to frequently pulling and inserting the USB cable Specifications Interface: USB Type C Current: 3 A Length: 1.5 m Use for: Raspberry Pi 4 Model B Packing List: 1x USB Type C power cable
€ 4,95
Leden € 4,46
Google Google Coral USB Accelerator
De Coral USB Accelerator voegt een Edge TPU coprocessor toe aan uw systeem. Het simpelweg aansluiten van deze accelerator op een USB poort maakt high-speed machine learning inferencing op een breed scala aan systemen mogelijk. Kenmerken Ondersteunde host OS: Debian Linux, macOS, Windows 10 Compatible met Raspberry Pi boards Ondersteund Framework: TensorFlow Lite Voert high-speed ML inferencing uit De on-board Edge TPU-coprocessor is in staat om 4 biljoen bewerkingen (tera-operations) per seconde (TOPS) uit te voeren, met behulp van 0,5 watt voor elke TOPS (2 TOPS per watt). Hij kan bijvoorbeeld op een energiezuinige manier state-of-the-art mobile vision modellen, zoals MobileNet v2, uitvoeren met bijna 400 FPS. Ondersteunt alle belangrijke platforms Werkt via een USB poort met elk systeem met Debian Linux (inclusief Raspberry Pi), macOS of Windows 10. Ondersteunt TensorFlow Lite Het is niet nodig om modellen van de grond af aan op te bouwen. TensorFlow Lite modellen kunnen worden gecompileerd om op de Edge TPU te worden uitgevoerd. Ondersteunt AutoML Vision Edge Bouw en implementeer, eenvoudig en op maat, snelle en uiterst nauwkeurige image classification modellen op uw apparaat met AutoML Vision Edge. Specificaties ML accelerator Google Edge TPU coprocessor:4 TOPS (int8); 2 TOPS per watt Connector USB 3.0 Type-C (data/power) Dimensies 65 x 30 mm Downloads/Documentatie Datasheet Get started with the USB Accelerator Model compatibility on the Edge TPU Edge TPU inferencing overview Run multiple models with multiple Edge TPUs Pipeline a model with multiple Edge TPUs PyCoral API (Python) Libcoral API (C++) Libedgetpu API (C++) Edge TPU compiler Pre-compiled models All software downloads
€ 89,95
Leden € 80,96
Elektor Classics Elex Archief (USB-stick)
Het tijdschrift Elex was van 1983 tot 1993 het kleine zusje van Elektor. In Elex werd elektronica op een niet moeilijke en leuke manier uitgelegd. Veel huidige Elektor-lezers zijn ooit begonnen met Elex. Elex is nostalgie. Dat blijkt uit de grote vraag die er steeds is gebleven naar de artikelen en schakelingen uit Elex. Daarom hebben we alle Elex-uitgaven in PDF-formaat op USB-stick gezet. Het gaat om in totaal 120 Elex-nummers, samen goed voor ruim 1400 artikelen, tips en trucs! Deze stick bevat, naast op informele wijze beschreven theorie, een schat aan eenvoudige en leuke schakelingen voor zelfbouw. Alle nummers zijn snel doorzoekbaar en gemakkelijk afdrukbaar.
€ 99,95€ 39,95
Leden identiek
Elektor Labs USB-RS232 Converter (FT231X BoB)
In 2011 we published a small PCB, FT232R USB/Serial Bridge/BOB (110553) with a USB-UART IC from FTDI, the FT232RQ. Here we present its successor with a cheaper version, an FT231XQ. But there are some other changes too. Instead of connectors, alongside the PCB, normal pin headers are used that are mounted on the bottom side and make the PCB a little smaller when mounted, compared to the old BoB. An ESD protection device (D1) is added in the USB data signal lines for extra safety. Despite less room for all parts to fit on the PCB, it is only a little over 2 mm longer. The FT231 has four configurable CBUS I/O pins, one less now. More importantly, however, the power supply for the I/O's VCCIO is only specified for +1.8 V to +3.3 but is 5 V tolerant for external UART logic running on +5 V. The +3.3 V internal regulator of the FT231 can deliver 50 mA to external circuitry. The manufacturer FTDI has a utility to configure several settings, FTPROG. Such as the function of the CBUS pins. By default, CBUS1 and CBUS 2 are low-level outputs to drive receive and transmit LEDs, indicating data transfer on the USB bus. So, when receiving data through the UART, the TX LED lights up. If you prefer this the other way around, FTPROG can be used to change this. But be careful the chip can become unresponsive when wrong settings are programmed. Some of the more important properties of the new BoB: Micro-USB connector USB 2.0 Full Speed capable VCCIO +1.8...+3.3 V (max. 4 V, 5 V input from UART logic tolerant) +3.3 V regulator output, max. 50 mA Data transfer 300 baud to 3 Mbaud UART Compatible with RS232, RS485, and RS422 I/O pin output drive 4 mA - 16 mA 4 configurable CBUS pins Here you can find information regarding the EEPROM Programming Utility, the VCP Drivers and the D2XX Drivers.
€ 19,95
Leden € 17,96
MagPi Archief (USB-stick)
Meer dan 6 MagPi jaargangen (2018 tot 2024) op USB-stick Deze USB-stick bevat alle MagPi-nummers van 2018 tot editie januari-februari 2024 in PDF-formaat. De laatste editie kan wel nu gratis voor iedereen worden gedownload. MagPi is het officiële magazine van de Raspberry Pi Foundation en bevat reviews, tutorials en DIY-projecten over en met de Raspberry Pi.
€ 69,95€ 49,95
Leden identiek
Andonstar Andonstar A1 USB Digital Microscope
Specifications DSP: High power Digital Image Monarch Processor Sensor: high-quality CMOS sensor, 2M pixel (hardware, no Interpolation) Resolution: 640x480,1600x1200 Interface: USB 1.1 / USB 2.0 Frame rate: 30 frames/sec (When resolution at 640x480), 1600x1200 5 frames/sec Focal distance: 5-30 mm (when Focal distance infinity, the microscope as a webcam, can not magnify) Magnification: Please refer to the sample photos and video Diameter: 12 mm USB cable length: about 165 cm USB cable color: black or transparent color (random) Lighting: 8x LED around the camera lens Included 1x Digital Microscope Camera 1x Software CD (User manual included) 1x Metal big base Stand
€ 79,95€ 54,95
Leden € 49,46
Nordic Semiconductor nRF52840 USB Dongle
The nRF52840 Dongle is a small, low-cost USB dongle that supports Bluetooth 5.3, Bluetooth mesh, Thread, ZigBee, 802.15.4, ANT and 2.4 GHz proprietary protocols. The Dongle is the perfect target hardware for use with nRF Connect for Desktop as it is low-cost but still support all the short range wireless standards used with Nordic devices. The dongle has been designed to be used as a wireless HW device together with nRF Connect for Desktop. For other use cases please do note that there is no debug support on the Dongle, only support for programming the device and communicating through USB. It is supported by most of the nRF Connect for Desktop apps and will automatically be programmed if needed. In addition custom applications can be compiled and downloaded to the Dongle. It has a user programmable RGB LED, a green LED, a user programmable button as well as 15 GPIO accessible from castellated solder points along the edge. Example applications are available in the nRF5 SDK under the board name PCA10059. The nRF52840 Dongle is supported by nRF Connect for Desktop as well as programming through nRFUtil. Features Bluetooth 5.2 ready multiprotocol radio 2 Mbps Long Range Advertising Extensions Channel Selection Algorithm #2 (CSA #2) IEEE 802.15.4 radio support Thread ZigBee Arm Cortex-M4 with floating point support DSP instruction set ARM CryptoCell CC310 cryptographic accelerator 15 GPIO available via edge castellation USB interface direct to nRF52840 SoC Integrated 2.4 GHz PCB antenna 1 user-programmable button 1 user-programmable RGB LED 1 user-programmable LED 1.7-5.5 V operation from USB or external Downloads Datasheet Hardware Files
€ 19,95
Leden € 17,96
JOY-iT JOY-iT AT34 USB Multimeter
Screen 0.96' IPS Display Refresh Rate 2 Hz Interface USB 3.0 (2.0 compatible) Quick Charge Recognition QC2.0, QC3.0, Apple 2.4 A /2.1 A / 1 A / 0.5 A, Android DCP, Samsung Voltage Measurement Range 3.7 V - 30 V Voltage Resolution 0.01 V Voltage Accuracy ±0,8 % (+4 digits) Current Measurement Range 0 A - 4 A Current Resolution 0.001 A Current Accuracy ±1 % (+4 digits) Power Measurement Range 0 W - 120 W Capacity Accumulation Range 0 mAh - 99999 mAh Energy Accumulation Range 0 Wh - 999,99 Wh Load Impedance Range 1 ? - 9999.9 ? Temperature Measurement Range 0 °C - 80 °C Operating Temperature Range 0 °C - 45 °C Temperature Measurement Error ± 3 °C Dimensions 64 mm x 22 mm x 12mm Weight 28 g
€ 17,50
Leden € 15,75
JOY-iT JOY-iT HD35 USB Load Resistor (35 W)
The HD35 offers you a compact electronic USB-load-resistor with a performance capability up to 35 Watt. The present current can be easily read on the LCD-Display. Moreover, the device has an adjustable trimmer and is because of this capable of simulating different charging electronics like QC2.0, QC3.0, FCP and AFC 9V. The maximal voltage is up tp 25 V and the maximal current is up to 5 A. This is the reason that it is suitable for nearly every area of application. The built-in cooling component in connection with the temperature controlled fan unit is very effective in cooling down the complete device. With the help of the integrated button it is possible to activate or deactivate the configurated load very fast. Features USB Load Resistor up to 35 W Adjustable via built-in trimmer LCD display of actual current strength Buttons for switching the load on/off Simulation of different charging electronics: QC2.0 (5 V, 9 V, 20 V), QC3.0, FCP, AFC 9V Technical Details Operating Voltage 4 V - 25 V Operating Current 0.25 A - 5 A Power 35 W Measuring Temperature Range -10 °C - 40 °C Display 4 Digit Segment Display Display Color Red Fan Speed 8000 RPM ± 10% | Temperature-controlled Connections USB 2.0, MicroUSB, USB Type-C Dimensions 84 mm x 41 mm x 28 mm Weight 52 g
€ 24,95
Leden € 22,46
-
, van Jean-François Simon Fnirsi FNB58 USB Tester (Review)
De Fnirsi FNB58 is een veelzijdige USB tester die naast spanning- stroom- en energiemetingen diverse extra mogelijkheden heeft. We gaan er mee aan de slag!