Build a custom Arduino Uno shield using the the Arduino Uno templates. Each pack contains six Arduino Uno templates. Downloads Gerber files

Lees meer minder

Need to dispense your own UV sensitive fluids (up to 550nm)? Inbegrepen 4x 5cc UV-Blocking Syringe Barrels 4x Standard Fit Pistons (white) 4x High Viscosity Fit Pistons (red) 4x Tip Caps 4x End Caps 2x Female to Female Luer couplers

Lees meer minder

A set of high precision drill bits, covering the most common drill bit sizes. Just pop them in the V-One Drill with a 2.5 mm hex key (not included) and start drilling. The following sizes are included (2 of each): 0.70 mm 0.80 mm 0.90 mm 1.00 mm 1.60 mm

Lees meer minder

Get creative and dispense your own fluids with this pack of cartridges.

Lees meer minder

Looking to dispense materials with a lower viscosity? These are the nozzles for you. Don't use this with our standard ink or solder paste... that will result in poor performance.This pack contains 4 extra fine nozzles with an internal diameter of 0.100 mm (4 mil)

Lees meer minder

If you want to push the resolution limits of the V-One, these dispensing tips will help enable your experimental projects. This pack contains 4 extra fine nozzles with an internal diameter of 0.150 mm (6 mil). Do not use with solder paste! It will clog!

Lees meer minder

The Punk Console circuit is an advanced tutorial to get you familiar with the V-One Drill attachment. Learn how to create a double sided board and turn the knobs to create music! The kit contains: 2x Green LEDs 8x 1k Resistors 3x 0.01uF Capacitor 2x 500K Trimpots 1x 556 Timer 1x Piezo Buzzer 1x 9 V Battery 1x 9 V Battery Connector Rivets and a V-One Drill are required.

Lees meer minder

These templates are your starting point if you’re building a Raspberry Pi HAT.Each pack contains six Raspberry Pi B+ templates.DownloadsGerber files

Lees meer minder

Use the right tool for the right job. These steel stakes are used to press the rivets on the PCB after holes have been drilled. They have been designed for optimum performance on the ink and ensure an electrical connection between the top and bottom layers of your PCB. Learn how to use them here.

Lees meer minder

Do you need a way to connect the top and bottom layers? Rivets are the key!Rivets are little copper tubes that make a mechanical connection between the top and bottom layer. We found rivets to be the easiest way to create vias. Be sure to pick up the corresponding rivet tool if you don't have one! Pack of 200 Inner Diameter - 1.0mm Head Diameter - 2.2mm Drill Size: 1.5mm (or 1.6mm) Confused on how to use them? Checkout our tutorial here.

Lees meer minder

Inbegrepen 1x Standard Nozzles (pack of 4) 1x Burnishing Pads (pack of 3) 1x 2'x3' Substrates (pack of 10) 1x 3'x4' Substrates (pack of 6) 1x 'Hello World' Kit

Lees meer minder

Soldeerpasta doseren en reflowen in één De Voltera V-One maakt dubbellaags prototype printplaten op uw eigen bureau. Gerber-bestanden gaan erin, geprinte printplaten komen eruit. De dispenser legt een zilver-gebaseerde geleidende inkt om uw schakeling ter plekke te printen. Het assembleren van printplaten is eenvoudig met de V-One's soldeerpasta verdeler en reflow functies. Plaats uw printplaat op het printbed en importeer uw Gerber-bestand in Voltera's software. Geen stencils meer nodig Voltera's software is ontworpen om gemakkelijk mee uit de voeten te kunnen. Vanaf het importeren van uw Gerber-bestanden tot het moment dat u op print drukt, leidt de software u veilig door elke stap. Compatibel met EAGLE, Altium, KiCad, Mentor Graphics, Cadence, DipTrace, Upverter. Inbegrepen V-One PCB-printer V-One dispenser V-One probe Spuitmondstuk Kopjes 3 x 4" FR1 substraatpakket 2 x 3" FR1 substraatpakket Substraatklemmen Duimschroefpakket Hello World-set Soldeerdraad Pincet Voeding Voedingsadapter Kabels Gebruiksaanwijzingen Downloads Specifications V-One Software User manuals Safety datasheets Technical datasheets Voltera CAM file for EAGLE Substrates and templates Meer Info Frequently Asked Questions More from the Voltera community Technische Specificaties Printspecificaties Minimum trace width 0.2 mm Minimum passive size 1005 Minimum pin-to-pin pitch (conductive ink) 0.8 mml Minimum pin-to-pin pitch (solder paste) 0.5 mml Resistivity 12 mΩ/sq @ 70 um height Substrate material FR4 Maximum board thickness 3 mm Soldeerspecificaties Solder paste alloy Sn42/Bi57.6/Ag0.4 Solder wire alloy SnBiAg1 Soldering iron temperature 180-210°C Drukbed Print area 135 x 113.5 mm Max. heated bed temperature 240°C Heated bed ramp rate ~2°C/s Footprint Dimensions 390 x 257 x 207 mm (L x W x H) Weight 7 kg Computervereisten Compatible operating systems Windows 7 or higher, MacOS 10.11 or higher Compatible file format Gerber Connection type Wired USB Certificatie EN 61326-1:2013 EMC requirements IEC 61010-1 Safety requirements CE Marking Affixed to the Voltera V-One printers delivered to European customers Ontworpen en geassembleerd in Canada. Meer technische informatie Quickstart Explore Flexible Printed Electronics on the V-One Voltera V-One Capabilities Reel Voltera V-One PCB Printer Walkthrough Unpacking the V-One V-One: Solder Paste Dispensing and Reflow All-in-One Voltera @ Stanford University's Bao Research Group: Robotic Skin and Stretchable Sensors Voltera @ Princeton: The Future of Aerospace Innovation

Lees meer minder

The Pico-10DOF-IMU is an IMU sensor expansion module specialized for Raspberry Pi Pico. It incorporates sensors including gyroscope, accelerometer, magnetometer, baroceptor, and uses I²C bus for communication. Combined with the Raspberry Pi Pico, it can be used to collect environment sensing data like temperature and barometric pressure, or to easily DIY a robot that detects motion gesture and orientation. Features Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series Onboard ICM20948 (3-axis gyroscope, 3-axis accelerometer, and 3-axis magnetometer) for detecting motion gesture, orientation, and magnetic field Onboard LPS22HB barometric pressure sensor, for sensing the atmospheric pressure of the environment Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 5 V Accelerometer Resolution: 16-bitMeasuring range (configurable): ±2, ±4, ±8, ±16gOperating current: 68.9uA Gyroscope Resolution: 16-bitMeasuring range (configurable): ±250, ±500, ±1000, ±2000°/secOperating current: 1.23mA Magnetometer Resolution: 16-bitMeasuring range: ±4900µTOperating current: 90uA Baroceptor Measuring range: 260 ~ 1260hPaMeasuring accuracy (ordinary temperature): ±0.025hPaMeasuring speed: 1Hz - 75Hz

Lees meer minder

Features No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing SPI interface, requires minimal IO pins Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 3.3 V Display color red, black, white Interface 3-wire SPI, 4-wire SPI Grey scale 2 Outline dimensions 74.00 × 37.5 0mm Full refresh time 15s Display size 60.088 × 30.704 mm Refresh power 42.4 mW (typ.) Dot pitch 0.203 × 0.202 mm Standby current <0.01 uA (almost none) Resolution 296×152 pixels Viewing angle >170° Downloads Wiki

Lees meer minder

Features SPI-compatible, easy to drive Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 5 V Digits 4 Dispaly size 0.4 inch LED color red Driver 74HC595 Display part no. FJ4401AH Dimensions 52 × 21 mm

Lees meer minder

Waveshare CoreEP4CE10 is an FPGA core board that features an EP4CE10F17C8N device onboard supporting further expansion. Features Onboard Serial Configuration Device EPCS16SI8N Integrated FPGA basic circuit, such as clock circuit Onboard nCONFIG button, RESET button, 4x LEDs All the I/O ports are accessible on the pin headers Onboard JTAG debugging/programming interface 2.00 mm header pitch design, suitable for being plugged-in your application system Downloads Wiki

Lees meer minder

Waveshare DVK600 is an FPGA CPLD mother board that features expansion connectors for connecting FPGA CPLD core board and accessory boards. DVK600 provides an easy way to set up FPGA CPLD development system. Features FPGA CPLD core board connector: for easily connecting core boards which integrate an FPGA CPLD chip onboard 8I/Os_1 interface, for connecting accessory boards/modules 8I/Os_2 interface, for connecting accessory boards/modules 16I/Os_1 interface, for connecting accessory boards/modules 16I/Os_2 interface, for connecting accessory boards/modules 32I/Os_1 interface, for connecting accessory boards/modules 32I/Os_2 interface, for connecting accessory boards/modules 32I/Os_3 interface, for connecting accessory boards/modules SDRAM interface for connecting SDRAM accessory board also works as FPGA CPLD pins expansion connectors LCD interface, for connecting LCD22, LCD12864, LCD1602 ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc. 5 V DC jack Joystick: five positions Buzzer Potentiometer: for LCD22 backlight adjustment, or LCD12864, LCD1602 contrast adjustment Power switch Buzzer jumper ONE-WIRE jumper Joystick jumper Downloads Schematics

Lees meer minder

The Pico-GPS-L76B is a GNSS module designed for Raspberry Pi Pico, with multi satellite systems support including GPS, BDS, and QZSS. It has advantages such as fast positioning, high accuracy, and low power consumption, etc. Combined with the Raspberry Pi Pico, it's easy to use global navigating function.Features Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards Multi satellite systems support: GPS, BDS, and QZSS EASY, self track prediction technology, help quick positioning AlwaysLocate, intelligent controller of periodic mode for power saving Supports D-GPS, SBAS (WAAS/EGNOS/MSAS/GAGAN) UART communication baudrate: 4800~115200bps (9600bps by default) Onboard battery holder, supports ML1220 rechargeable cell, for preserving ephemeris information and hot starts 4x LEDs for indicating the module operating status Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications GNSS Frequency band:GPS L1 (1575.42 Mhz)BD2 B1 (1561.098 MHz) Channels: 33 tracking ch, 99 acquisition ch, 210 PRN ch C/A code SBAS: WAAS, EGNOS, MSAS, GAGAN Horizontal position accuracy(autonomous positioning) <2.5 m CEP Time-To-First-Fix @ -130 dBm(EASY enabled) Cold starts: <15s Warm starts: <5s Hot starts: <1s Sensitivity Acquisition: -148 dBm Tracking: -163 dBm Re-acquisition: -160 dBm Dynamic performance Altitude (max): 18000 m Velocity (max): 515 m/s Acceleration (max): 4 g Others Communication interface UART Baudrate 4800~115200bps (9600bps by default) Update rate 1 Hz (default), 10 Hz (max) Protocols NMEA 0183, PMTK Power supply voltage 5 V Operating current 13 mA Overall current consumption < 40 mA@5 V (Continue mode) Operating temperature -40? ~ 85? Dimensions 52 × 21 mm Included 1x Pico-GPS-L76B 1x GPS Antenna

Lees meer minder

Specifications CM4 socket Suitable for all variants of Compute Module 4 Networking Gigabit Ethernet RJ45 connectorM.2 M KEY, supports communication modules or NVME SSD Connector Raspberry Pi 40-PIN GPIO header USB 2x USB 2.0 Type A2x USB 2.0 via FFC connector Display MIPI DSI display port (15-pin 1.0 mm FPC connector) Camera 2x MIPI CSI-2 camera port (15-pin 1.0 mm FPC connector) Video 2x HDMI port (including one port via FFC connector), supports 4K 30fps output RTC N/A Storage MicroSD card socket for Compute Module 4 Lite (without eMMC) variants Fan header No fan control, 5 V Power input 5 V Dimensions 85 x 56 mm Included 1x CM4-IO-BASE-A 1x SSD mounting screw Downloads Wiki

Lees meer minder

De Waveshare PCIe naar Gigabit Ethernet en USB 3.2 Gen 1 HAT+ is een uitbreidingskaart die speciaal is ontworpen voor de Raspberry Pi 5. Het verbetert de connectiviteit van de Raspberry Pi door drie snelle USB 3.2 Gen 1 toe te voegen poorten en een Gigabit Ethernet-poort, allemaal in een plug-and-play-configuratie zonder stuurprogramma's. Kenmerken Gebaseerd op de 16-pins PCIe-interface van Raspberry Pi 5 Uitgerust met RTL8153B krachtige Gigabit Ethernet chip Ondersteunt Raspberry Pi OS, Ubuntu, OpenWRT, enz. Stabiele en betrouwbare netwerksnelheid Realtime monitoring van de energiestatus Ondersteunt de stroomregeling van de USB-poort via software Inbegrepen 1x PCIe naar Gigabit Ethernet USB 3.2 HAT+ 1x Netwerkkabel (1,5 m) 1x 16P-kabel (40 mm) 1x Standoff-pakket Downloads Wiki

Lees meer minder

This PCIe to M.2 adapter is specifically designed for the Raspberry Pi 5. It supports the NVMe protocol for M.2 SSDs, enabling fast read and write operations, and adheres to the HAT+ standard. The adapter is compatible with M.2 SSDs in the 2230 and 2242 sizes. Inbegrepen 1x PCIe to M.2 HAT+ Adapter 1x 2x20 Pin header 1x 16P cable (40 mm) 1x Standoff pack Downloads Wiki

Lees meer minder

De Waveshare PoE M.2 HAT+ (B) combineert Power over Ethernet (PoE) en PCIe-naar-M.2-functionaliteit voor de Raspberry Pi 5. Hij ondersteunt de IEEE 802.3af/at-netwerkstandaarden en is geschikt voor M.2 NVMe SSD's in de formaten 2230, 2242, 2260 en 2280. Bovendien maakt hij SSD-boot mogelijk voor de Raspberry Pi. Kenmerken Standaard Raspberry Pi 40-pins GPIO-uitbreidingsheader, compatibel met Raspberry Pi 5 Ondersteunt Power over Ethernet (PoE) en voldoet aan de IEEE 802.3af/at-netwerkstandaarden Maakt gebruik van een volledig geïsoleerde Switch Mode Power Supply (SMPS) voor stabiele stroomvoorziening Ondersteunt harde schijven met NVMe-protocol M.2-interface, voor hoge lees-/schrijfsnelheden en een hoge efficiëntie Biedt 1x PCIe in Gen2- of Gen3-modus Speciaal ontworpen voor de Raspberry Pi 5 Compatibel met M.2 SSD's in de formaten 2230, 2242, 2260 en 2280 Specificaties PoE-voedingsingang 37~57 V DC Uitgangsvermogen GPIO-header: 5 V/4,5 A (max.)2P-header: 12 V/2 A (max.) Netwerkstandaard IEEE 802.3af/at PoE Afmetingen 56 x 85 mm Inbegrepen 1x Waveshare PoE M.2 HAT+ (B) 1x 16-pins PCIe-kabel 1x SSD-montageschroef 1x Schroevenset Downloads Wiki

Lees meer minder

De PoE HAT (G) is een IEEE 802.3af/at-compatibele PoE (Power Over Ethernet) HAT voor Raspberry Pi 5. Door gebruik te maken van een PoE-router of switch die de IEEE 802.3af/at-netwerkstandaard ondersteunt, is het mogelijk om zowel de netwerkverbinding als de voeding voor uw Raspberry Pi te verzorgen in slechts één Ethernet-kabel. Kenmerken Standaard Raspberry Pi 40-pins GPIO-header PoE-mogelijkheid, IEEE 802.3af/at-compatibel Originele IC-oplossing aan boord voor stabielere PoE-stroomprestaties Keurt gebruik van niet-geïsoleerde geschakelde voeding (SMPS) Compact en eenvoudig te monteren Specificaties PoE-voedingsingang 38~57 V DC in Vermogensuitgang GPIO-header: 5 V/5 A (max) Netwerkstandaard IEEE 802.3af/at PoE Afmetingen 56,5 x 64,98 mm Inbegrepen 1x PoE HAT (G) 1x 2x2 header 1x 2x20 header 1x Standoffs-pakket Downloads Wiki

Lees meer minder

Dit polysilicium zonnepaneel (18 V / 10 W) biedt stabiele prestaties met een hoge conversie efficiëntie van >20%. Specificaties Type zonnecel Polysilicium Uitgangsvermogen tolerantie ±3% Bedrijfsspanning 17,6 V Open circuit spanning 21,6 V Hoeveelheid cellen 36 (4x9) Vermogen 10 Wp (max) Conversie efficiëntie >20% Bedrijfsstroom 0,57 A Kortsluitstroom 0,61 A Standaard systeemspanning 1000 V (max) Bedrijfstemperatuur -40° C ~ +85°C Druk op paneel 30 m/s (200 kg/m²) (max) Kabel Lengte 90 cm, DC stekker, OD 3,5 mm ID 1,35 mm Frame materiaal Anodische oxidatie aluminiumlegering Afmetingen 340 x 232 x 17 mm Gewicht 0,935 kg

Lees meer minder