Zoekresultaten voor "elektor OR magazine OR nl OR maart OR april OR 2019 OR pdf"

In 2011 we published a small PCB, FT232R USB/Serial Bridge/BOB (110553) with a USB-UART IC from FTDI, the FT232RQ. Here we present its successor with a cheaper version, an FT231XQ. But there are some other changes too. Instead of connectors, alongside the PCB, normal pin headers are used that are mounted on the bottom side and make the PCB a little smaller when mounted, compared to the old BoB. An ESD protection device (D1) is added in the USB data signal lines for extra safety. Despite less room for all parts to fit on the PCB, it is only a little over 2 mm longer. The FT231 has four configurable CBUS I/O pins, one less now. More importantly, however, the power supply for the I/O's VCCIO is only specified for +1.8 V to +3.3 but is 5 V tolerant for external UART logic running on +5 V. The +3.3 V internal regulator of the FT231 can deliver 50 mA to external circuitry. The manufacturer FTDI has a utility to configure several settings, FTPROG. Such as the function of the CBUS pins. By default, CBUS1 and CBUS 2 are low-level outputs to drive receive and transmit LEDs, indicating data transfer on the USB bus. So, when receiving data through the UART, the TX LED lights up. If you prefer this the other way around, FTPROG can be used to change this. But be careful the chip can become unresponsive when wrong settings are programmed. Some of the more important properties of the new BoB: Micro-USB connector USB 2.0 Full Speed capable VCCIO +1.8...+3.3 V (max. 4 V, 5 V input from UART logic tolerant) +3.3 V regulator output, max. 50 mA Data transfer 300 baud to 3 Mbaud UART Compatible with RS232, RS485, and RS422 I/O pin output drive 4 mA - 16 mA 4 configurable CBUS pins Here you can find information regarding the EEPROM Programming Utility, the VCP Drivers and the D2XX Drivers.

Lees meer minder

De RangePi - LoRa USB Dongle maakt gebruik van de Semtech SX1262 die communicatie tot 5 km mogelijk maakt. De RangePi kan worden gebruikt met elk apparaat dat gebruik maakt van een USB-aansluiting, waardoor er geen extra apparatuur nodig is om verbinding te maken met het LoRa-netwerk. Specificaties 1,14' LCD RP2040 MCU Tot 5 km afstand UART Inbegrepen 1x RangePi 1x antenne Downloads STEP File Productafmeting 3D PDF File Schematisch bestand GitHub

Lees meer minder

Un support de cours réputé et adopté par de nombreux enseignants, avec 60 pages d'exercices corrigés Reconnu et utilisé par les enseignants de nombreuses écoles et IUT, complété d'exercices accompagnés de leurs corrigés, cet ouvrage original et érudit est une référence sur tous les fondamentaux de la programmation: choix d'une structure de données, paramétrage, modularité, orientation objet en héritage, conception d'interface, multithreading et gestion d'événements, protocoles de communication et gestion réseau, bases de données jusqu'à la désormais indispensable norme Unicode (le format UTF-8). On verra notamment la réalisation avec Python 3 d'une application web interactive et autonome, intégrant une base de données SQLite. Cette nouvelle édition traite de la possibilité de produire des documents imprimables (PDF) de grande qualité en exploitant les ressources combinées de Python 2 et Python 3. À qui s'adresse ce livre? Aux étudiants en BTS et IUT Informatique et à leurs enseignants À tous les autodidactes férus de programmation qui veulent découvrir le langage Python

Lees meer minder

Dive into the world of Raspberry Pi with this huge book of tutorials, project showcases, guides, product reviews, and much more from the writers of The MagPi, the official Raspberry Pi magazine. Raspberry Pi Pico 2 joins Raspberry Pi 5 in this, The Official Raspberry Pi Handbook 2025. Pico 2 comes with a faster processor than the original Pico, and uses less power – while still maintaining the same form factor and pinout. With both Pico 2 and Raspberry Pi 5 you can power any project you can imagine. With 200 pages packed full of maker goodness, you’ll also find inspiration for your Raspberry Pi Zero 2 W, Raspberry Pi 4, or any other Raspberry Pi model you have – there’s something for everyone. In this handbook you’ll find: A get started guide that covers every Raspberry Pi Everything you need to know about the brand-new Raspberry Pi Pico 2 Inspiring projects to spark your next build idea Tutorials for makers of all skill levels Guides for media centres, game emulators, and more! Raspberry Pi Pico 2 Microcontroller not included This bumper book is your definitive guide to everything Raspberry Pi. It’s essential for any maker with big dreams and a thirst for knowledge.

Lees meer minder

De EggBot is een gemakkelijk te bedienen open-source robot, die allerlei vormen kan tekenen op bolvormige en eivormige voorwerpen. De EggBot heeft een groot aantal instelmogelijkheden en kan bijvoorbeeld tekenen en op eieren, maar ook golfballen, gloeilampen, kerstballen en zelfs wijnglazen. Mogelijkheden van de EggBot Deluxe Gebruik de bot om indrukwekkende paaseieren te creëren, maak uw eigen kerstversiering of personaliseer uw golfballen. De EggBot is niet alleen een cool gadget, het biedt ook een geweldige introductie in de wereld van CNC (Computer Numerical Control) en doe-het-zelf robotica. Alle elektronica en software in de Eggbot kunt u aanpassen en zelfs voor andere toepassingen gebruiken. Hoe werkt de robot? De EggBot wordt aangeboden in vorm van een bouwpakket en wordt geleverd inclusief een universele netvoeding (met US-EU-adapter). De Eggbot is makkelijk in elkaar te zetten in een paar uur en heeft alleen een paar basis tools nodig zoals een platte schroevendraaier. Solderen is niet nodig. Met behulp van de EggBot-software, open source, kunt u deze machine aansturen vanuit Inkscape, een uitstekend freeware illustratieprogramma (voor Mac-, Windows-en Linux-computers). U kunt zelf een afbeelding tekenen, een foto inscannen of ontwerpen uit andere programma's importeren. U kunt de EggBot ook vanuit veel andere programma’s aansturen wanneer deze de mogelijkheid bezitten om seriële commando’s te versturen via een USB-poort.

Lees meer minder

The AxiDraw SE/A3 has the same extended plotting area as the AxiDraw V3/A3. In place of the central extrusion that makes up the body of that machine, the AxiDraw SE/A3 has a central beam that is CNC machined from a solid billet of 6061-T6 aluminum, and then anodized to a sleek black finish.This heavy, rigid structure – it's a solid block of metal! – provides dramatically better straightness and stiffness, even compared to the already-stiff AxiDraw V3/A3. This design adds mass exactly where you want it: to the non-moving base that forms the X-axis of the machine. In order to keep the weight light where it matters, the moving Y-axis of the AxiDraw SE/A3 uses the same stiff and light custom aluminum extrusion that we use on the AxiDraw V3/A3.Beyond this, the central beam and X-axis of the AxiDraw SE/A3 feature an all-new geometry for the rolling wheels, which provides more stable and uniform motion along the axis.Getting StartedThe AxiDraw comes fully assembled, tested, and ready to use, right out of the box. A universal-input plug-in power supply is included with the AxiDraw, as is a USB cable, and an optional paper-holding easel. Assuming that you've installed the software first, you can be up and plotting within minutes of opening the box. Our comprehensive PDF user guide walks you through every step of the process.To operate AxiDraw, you will need a reasonably modern computer with an available USB port (Mac, Windows or Linux), plus internet access to download necessary software. Pens and paper are not included. (You can use your own; AxiDraw does not require proprietary pens or paper.)AxiDraw is normally controlled through a set of extensions to Inkscape, the excellent, popular and free vector graphics program. Basic operation is much like that of a printer driver: you import or make a drawing in Inkscape, and use the extensions to plot your text or artwork. It's all handled through a straightforward graphical user interface, and works cleanly on Mac, Windows and Linux.SpecificationsPerformance Usable pen travel (inches): 16.93 × 11.69 inches Usable pen travel (millimeters): 430 × 297 mm Vertical pen travel: 0.7 inch (17 mm) Maximum XY travel speed: 15 inches (38 cm) per second Native XY resolution: 2032 steps per inch (80 steps per mm) Reproducibility (XY): Typically better than 0.005 inches (0.1 mm) at low speeds. Physical Major structural components are machined and/or folded aluminum. Holds pens and other drawing instruments up to 1' (25.4 mm) diameter. Overall dimensions: Approximately 26 × 19 × 5 inches (66 × 48 × 13 cm) Maximum height with cable guides: Approximately 11 inches (29 cm) Footprint: Approximately 26 × 5 inches (66 x 13 cm) Weight: 8.4 Lb (3.8 kg) Software Compatible with Mac, Windows, and Linux Drive directly from within Inkscape, using the AxiDraw extension. Comprehensive user guide available for download Driver software software free to download and open source Internet access is required to download software. Additionally, AxiDraw Merge software available at no cost to AxiDraw owners. Programming interfaces Note: Programming is not required to use the AxiDraw. Stand-alone command line interface (CLI) Available AxiDraw Python API RESTful API available for full machine control, stand-alone or accessible by running RoboPaint in the background. Simplified 'GET-only' API available as well, for use in programming environments (such as Scratch, Snap) that permit only retrieval of URLs. Direct EiBotBoard (EBB) command protocol available for use in any programming environment that supports communication with USB-based serial ports. Code that generates SVG files can also be used to (indirectly) control the machine. Included AxiDraw SE/A3 writing and drawing machine (fully assembled, tested, and ready to use) Multi-plug power supply with EU adapter USB cable Tabloid/A3 Clip Easel (Board and clips) for paper holding Standard AxiDraw pen clip and XL pen clip Italic pen adapter DownloadsUser Guide

Lees meer minder

As compared to the (US Letter/A4 sized) AxiDraw V3, the AxiDraw V3/A3 has extended travel range, designed for use with paper sizes up to and including 11 × 17 inch ('tabloid' or 'ledger') and A3. It can work with any paper up to and including that size, including envelopes, regular US letter (8 1/2 × 11 inch) or A4 (297 × 210 mm) sized paper, note cards, business cards, or a whole array of smaller items. The AxiDraw comes with a mounting easel (board with clips) that can be used for holding paper, cards, and envelopes of various sizes. The AxiDraw V3/A3 also comes standard with AxiDraw Outrigger Feet pre-installed, for greater stance and stability while plotting. The unique design of the AxiDraw features a drawing head that extends beyond the body of the machine, making it possible to also draw on flat objects bigger than the machine itself. For example, you can set it right on top of a box to write an address or add decorations. You can even set it on top of a poster board, chalkboard, or whiteboard to draw graphics in place. The pen holder fits a wide variety of pens, including Sharpie fine and ultra-fine point markers, most rollerball and fountain pens, small-bodied whiteboard markers, and so forth. It can even hold a fountain pen at a proper angle of 45° to the paper. You can also use implements that aren't pens, such as pencils, chalk, charcoal, brushes, and many others. However, you'll get the best results with instruments such as fountain pens and rollerball pens, which do not require the user to apply pressure. Getting Started The AxiDraw comes fully assembled, tested, and ready to use, right out of the box. A universal-input plug-in power supply is included with the AxiDraw, as is a USB cable, and an optional paper-holding easel. Assuming that you've installed the software first, you can be up and plotting within minutes of opening the box. The comprehensive PDF user guide walks you through every step of the process. To operate AxiDraw, you will need a reasonably modern computer with an available USB port (Mac, Windows or Linux), plus internet access to download necessary software. Pens and paper are not included. (You can use your own! AxiDraw does not require proprietary pens or paper.) AxiDraw is normally controlled through a set of extensions to Inkscape, the excellent, popular and free vector graphics program. Basic operation is much like that of a printer driver: you import or make a drawing in Inkscape, and use the extensions to plot your text or artwork. It's all handled through a straightforward graphical user interface, and works cleanly on Mac, Windows and Linux. Specifications Performance Usable pen travel (inches): 16.93 × 11.69 inches Usable pen travel (millimeters): 430 × 297 mm Vertical pen travel: 0.7 inch (17 mm) Maximum XY travel speed: 15 inches (38 cm) per second Native XY resolution: 2032 steps per inch (80 steps per mm) Reproducibility (XY): Typically better than 0.005 inches (0.1 mm) at low speeds. Physical Major structural components are machined and/or folded aluminum. Holds pens and other drawing instruments up to 5/8' (16 mm) diameter. Overall dimensions: Approximately 26 × 18.5 × 4 inches (66 × 47 × 10 cm) Maximum height with cable guides: Approximately 11 inches (29 cm) Footprint: Approximately 26 × 5 inches (66 x 13 cm) Physical weight: 5.5 Lb (2.5 kg) Software Compatible with Mac, Windows, and Linux Drive directly from within Inkscape, using the AxiDraw extension. Comprehensive user guide available for download. Driver software software free to download and open source Internet access is required to download software. Additionally, AxiDraw Merge software available at no cost to AxiDraw owners. Programming interfaces Note: Programming is not required to use the AxiDraw. Stand-alone command line interface (CLI) Available AxiDraw Python API RESTful API available for full machine control, stand-alone or accessible by running RoboPaint in the background. Simplified 'GET-only' API available as well, for use in programming environments (such as Scratch, Snap) that permit only retrieval of URLs. Direct EiBotBoard (EBB) command protocol available for use in any programming environment that supports communication with USB-based serial ports. Code that generates SVG files can also be used to (indirectly) control the machine. Included AxiDraw V3/A3 writing and drawing machine (fully assembled, tested, and ready to use) Multi-plug power supply with EU adapter USB cable Easel (Board and clips) for paper holding Downloads User Guide

Lees meer minder

Pixel Pump is een open source vacuümpomp voor handmatige SMD-assemblage. Hij wordt geleverd met een comfortabele pen, een voetpedaal, RGB LED-knoppen en een aantal functies die handmatige assemblage veel leuker maken. Het is de perfecte metgezel voor het handmatig SMD-solderen, van individuele prototypes tot kleine productieruns. Doordacht ontwerp van hoge kwaliteit Pixel Pump wordt geleverd met een set van vijf roestvrijstalen mondstukken in vijf verschillende maten, met buitendiameters van 0,3 mm tot 1,8 mm. Met deze set zou je de meeste SMD-componenten moeten kunnen plaatsen, inclusief kleine 0402-componenten, grotere onderdelen zoals spoelen en IC's, en zowat alles daartussenin. De mondstukken worden op hun plaats gehouden door een Luer lock slip fitting die snel wisselen van deze mogelijk maakt en brede compatibiliteit met mondstukken van andere fabrikanten. De pen zelf heeft een snelkoppeling voor de luchtslang en vier M8 stalen moeren om hem wat stevigheid te geven en magnetische bevestiging aan de Pixel Pump mogelijk te maken. Tactiele siliconen knoppen met RGB-achtergrondverlichting bieden volledige controle over het apparaat. Je kunt de werkingsmodi wijzigen, schakelen tussen hoge en lage energie-instellingen of de omgekeerde modus activeren om de zuigmond te reinigen. Met de knoppen kun je ook dingen configureren zoals zuigkracht en LED-helderheid. Pixel Pump heeft een drukontlastingsventiel dat vacuüm dumpt om ervoor te zorgen dat je onderdeel snel wordt vrijgegeven wanneer je het voetpedaal loslaat. Optioneel kun je dat ventiel zo instellen dat het overschakelt van de zuigmodus naar de drukmodus, waardoor het mondstuk snel en eenvoudig wordt gereinigd als je per ongeluk vuil hebt opgezogen, zoals soldeerpasta. Een gesinterd luchtfilter beschermt de vacuümpomp en kleppen tegen vuil dat anders in het systeem zou kunnen worden gezogen. Het is van buitenaf toegankelijk en kan eenvoudig worden gereinigd en hergebruikt. Een perfecte metgezel voor prototypeboards en kleinschalige productie Pixel Pump is voornamelijk ontworpen voor mensen en organisaties die eenmalige prototypes maken, maar het is ook zeer geschikt voor kleine productieseries. Het is zeer eenvoudig te gebruiken en is eigenlijk sneller dan een geautomatiseerde pick-and-place machine voor kleinere batchgroottes, vooral in combinatie met SMD-Magazijnen. Pixel Pump is de perfecte metgezel voor hobbyisten en professionals die graag hun eigen printplaten maken. Kenmerken Comfortabele pen waarin verschillende mondstukken passen Kleine, flexibele, hittebestendige siliconenslang die de pen met de Pixel Pump verbindt Magnetische basis voor de pen Sterk, regelbaar vacuüm, perfect voor het oppakken van zowel kleine als grote onderdelen Tactiele, siliconen RGB-knoppeninterface Voetpedaal voor het activeren van de pomp Instelbaar hoog/laag vermogen Instelbare LED-helderheid Omgekeerde modus, die druk creëert in plaats van zuigkracht om mondstukken te reinigen Vacuümontlastklep voor snelle drukverlaging om onderdelen sneller te laten vallen Eenvoudige software-updates via USB-C Compact ontwerp dat het beperkte oppervlak van je werkbank respecteert Downloads 3D STL Files Firmware Mainboard Schematics UI Board Schematics Motor Controller Schematics

Lees meer minder