ESP32

41 producten


  • ESP32-C3-DevKitM-1

    Espressif ESP32-C3-DevKitM-1

    Niet op voorraad

    ESP32-C3-DevKitM-1 is een ontwikkelingsboard voor beginners, gebaseerd op de ESP32-C3-MINI-1, een module die zijn naam dankt aan zijn kleine afmetingen. Dit board beschikt over volledige Wi-Fi en Bluetooth LE functies. De meeste I/O-pinnen op de ESP32-C3-MINI-1 module zijn uitgesplitst naar de pin headers aan beide zijden van dit board voor eenvoudige interfacing. Ontwikkelaars kunnen randapparatuur aansluiten met jumper draden of de ESP32-C3-DevKitM-1 op een breadboard monteren. Specificaties ESP32-C3-MINI-1 ESP32-C3-MINI-1 is een universele Wi-Fi en Bluetooth LE combo-module die wordt geleverd met een PCB-antenne. Het hart van deze module is de ESP32-C3FN4, een chip met een embedded flash van 4 MB. Omdat de flash geïntegreerd is in de ESP32-C3FN4 chip, in plaats van in de module, heeft de ESP32-C3-MINI-1 een kleiner formaat. 5 V naar 3.3 V LDO Spanningsregelaar die een 5 V voeding omzet in 3,3 V. 5 V Power On LED Schakelt in wanneer de USB-voeding op het board wordt aangesloten. Pin Headers Alle beschikbare GPIO-pinnen (behalve de SPI-bus voor flash) zijn uitgesplitst naar de pin headers op het board. Zie voor details Header Block. Boot knop Downloadknop. Als je Boot ingedrukt houdt en dan op Reset drukt, start de modus Firmware Download voor het downloaden van firmware via de seriële poort. Micro-USB poort USB-interface. Voeding voor het board en de communicatie-interface tussen een computer en de ESP32-C3FN4 chip. Reset knop Druk op deze knop om het systeem opnieuw op te starten. USB-to-UART Bridge Single USB-UART bridge chip biedt overdrachtssnelheden tot 3 Mbps. RGB LED Adresseerbare RGB LED, aangestuurd door GPIO 8. Downloads ESP32-C3 Datasheet ESP32-C3-MINI-1 Datasheet ESP32-C3-DevKitM-1 Schematic ESP32-C3-DevKitM-1 PCB Layout ESP32-C3-DevKitM-1 Dimensions

    Niet op voorraad

    € 19,95

    Leden € 17,96

  • ESP32-PICO-Kit V4

    Espressif ESP32-PICO-Kit V4

    De ESP32-PICO-KIT past in een mini breadboard. Het is volledig functioneel met een minimaal aantal discrete componenten, terwijl alle ESP32 pinnen beschikbaar zijn.Kenmerken Volledige up-to-date documentatie is beschikbaar. Alle beschreven instructies en commando’s werken zoals aangeven. Er is ook veel aanvullende informatie en hardware documentatie beschikbaar. Toepassingen voor de ESP32-PICO-KIT kunnen worden ontwikkeld op Windows, Linux of Mac. Twe cores en draadloosNet als de ESP8266 heeft de ESP32 WiFi, maar voegt daar Bluetooth aan toe. Hij heeft ook twee 32-bits cores aan boord, waardoor hij extreem krachtig is, en alle poorten en interfaces biedt die de ESP8266 mist. Je zou simpelweg kunnen stellen dat de ESP8266 een WiFi-controller is die wat I/O biedt, terwijl de ESP32 een volwaardige controller is die ook WiFi heeft.ESP32 randapparatuurDe ESP32 bevat een ADC &DAC, touch sensor circuits, een SD/SDIO/MMC host controller, een SDIO/SPI slave controller, een EMAC, PWM om LED's en motoren aan te sturen, UART, SPI, I²C, I²S, infrarood afstandsbediening en, natuurlijk, GPIO.ESP32-PICO-KIT Development board V4De ESP32-PICO-D4 is een System-on-Chip (SoC) die een ESP32-chip integreert in een 4 MB SPI-flashgeheugen van 7 x 7 mm.De ESP32-PICO-KIT is een breakout board voor deze SoC met een on-board USB-naar-serieel converter voor eenvoudig programmeren en debuggen.Behalve het board heb je ook een programming toolchain nodig. Volledige, up-to-date documentatie van Espressif is beschikbaar op de Read the Docs website.Alle beschreven instructies en commando’s werken zoals aangeven. Er is ook veel aanvullende informatie en hardware documentatie beschikbaar.Toepassingen voor de ESP32-PICO-KIT kunnen worden ontwikkeld op Windows, Linux of Mac.

    € 19,95

    Leden € 17,96

  •  -17% Elektor Ronde Kerstboomkit

    Elektor Labs Elektor Ronde Kerstboomkit

    Niet op voorraad

    DIY 3D programmeerbare lichteffecten Deze op Arduino gebaseerde kerstboomkit bevat 36 digitaal programmeerbare 8 mm RGB-LED's (WS2812D-F8) die individueel adresseerbaar zijn voor het creëren van indrukwekkende lichteffecten. De LED's kunnen extern worden aangestuurd of via een Arduino Nano ESP32. Kenmerken 36 digitale RGB-LED's (NeoPixel-adresseerbaar) Geschikt voor elk microcontrollersysteem Perfecte match met Arduino Nano ESP32 (niet inbegrepen) Hoogwaardige printplaten: 5x rond, 1x vierkant Eenvoudige, leuke montage met populaire gereedschappen Gedetailleerde constructiehandleiding Afmetingen: 136 x 136 x 175 mm Inbegrepen Print (136 x 136 mm) Weerstanden R1...R36 = 75 Ω, 0,125 W, 5%, SMD 0805 P1 = instelpotmeter liggend 10 kΩ, 0,1 W, 20%, 6 mm rond (Piher PT6KV-103A2020) Condensatoren C1...C36 = 100 n, 50 V, 5%, X7R, SMD 0805 C37, C38 = 47u, 6V3, 10%, tantaal, case A (1206) Halfgeleiders D1, D2 = S5J-E3/57T, SMD-behuizing SMC LED1-LED36 = WS2812D-F8, 8 mm, THT Diversen K1, JP1 = pinheader, 3×1, verticaal, raster 2,54 mm Jumper voor JP1, steek 2,54 mm K2 = MJ-179PH (Multicomp Pro), DC-voedingsconnector, 4 A, pindiameter 1,95 mm S1 = DIP-schakelaar, 4-voudig PA1...PE6 = 2 m draad, 0,81 mm massief, 0,52 mm²/20AWG, groene isolatie (Alpha Wire 3053/1 GR005) H1...H5 = nylon afstandsbus, female/female, M3, 5 mm H1...H5 = nylon boutje, M3, 5 mm Optioneel Arduino Nano ESP32 met Headers Links Elektor Labs

    Niet op voorraad

    € 29,95€ 24,95

    Leden identiek

  • ESP32-Cam-CH340 Development Board

    Espressif ESP32-Cam-CH340 Development Board

    Features Product model: HW-818 Working voltage: DC 5V Product size: 27mm x 48.5 mm x 4.5 mm / 1.06” x 1.9” x 0.17” SPI Flash: Default 32Mbit RAM: Internal 520KB + External 4MPSRAM Bluetooth: Bluetooth 4.2 BR/EDR and BLE standards Wi-Fi: 802 II b/g/n/e/i Support interfaces: UART, SPI, I2C, PWM Supporting TF Card: Maximum Supporting 4G IO port: 9 Serial port rate: default 115200 BPS Image output format: JPEG (OV2640 only), BMP, GRAYSCALE Spectrum range: 2412-2484 MHz Antenna form: board PCB antenna, gain 2dBi Transmitting power: 802.l1b: 17 + 2dBm (1lMbps) 802.l1g:14+2dBm (54Mbps) 802.l1n:13+2dBm (MCS7)

    € 11,95

    Leden € 10,76

  • JOY-iT NodeMCU ESP32 Development Board

    JOY-iT JOY-iT NodeMCU ESP32 Development Board

    Met de NodeMCU-ESP32 is comfortabel prototyping mogelijk met eenvoudige programmering via Luascript of de Arduino IDE en het breadboard-compatibele ontwerp. Dit bord heeft 2.4 GHz dual-mode Wifi en een BT draadloze verbinding. Bovendien zijn een 512 KB SRAM en een 4 MB geheugen geïntegreerd op het microcontroller ontwikkelbord. Het bord heeft 21 pinnen voor interface verbindingen, waaronder I²C, SPI, UART, DAC en ADC.Specificaties TypeType ESP32 Processor Tensilica LX6 Dual-Core Klokfrequentie 240 MHz SRAM 512 kB Geheugen 4 MB Draadloze Lan 802.11 b/g/n Frequentie 2.4 GHz Bluetooth Klassiek / LE Data-interfaces UART / I²C / SPI / DAC / ADC Werkingssspanning 3,3 V (bruikbaar via 5 V microUSB) Werkingsstemperatuur -40°C - 125°C Afmetingen 48 x 26 x 11.5 mm Gewicht 10 g Downloads Handleiding Frequency 2.4 GHz Bluetooth Classic / LE Data Interfaces UART / I²C / SPI / DAC / ADC Operating Voltage 3.3 V (operable via 5 V microUSB) Operating Temperature –40°C – 125°C Dimensions 48 x 26 x 11.5 mm Weight 10 g DownloadsManual

    € 12,95

    Leden € 11,66

  • ESP32-DevKitC-32D

    Espressif ESP32-DevKitC-32D

    Niet op voorraad

    ESP32-DevKitC V4 is a small-sized ESP32-based development board produced by Espressif. Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can connect these pins to peripherals as needed. Standard headers also make development easy and convenient when using a breadboard. The board supports various ESP32 modules, including ESP32-WROOM-32, ESP32-WROOM-32U, ESP32-WROOM-32D, ESP32-SOLO-1, and ESP32-WROVER series. The following list and figure below describe key components, interfaces and controls of ESP32-DevKitC V4 board ESP32-WROOM-32 module soldered to the ESP32-DevKitC V4 board. Optional Space for ESP32-WROVER: Longer ESP32-WROVER modules may be soldered instead of the ESP32-WROOM-32. A single chip USB-to-UART bridge provides up to 3 Mbps transfers rates. Download button: holding down the Boot button and pressing the EN button initiates the firmware download mode. Then the user can download firmware through the serial port. EN Button: Reset button - pressing this button resets the system Micro USB Port: USB interface. It functions as the power supply for the board and the communication interface between PC and the ESP module. 5 V Power On LED: This LED lights when the USB or an external 5 V power supply is applied to the board. I/O Connector: Most of the pins on the ESP module are broken out to the pin headers on the board. Users can program ESP32 to enable multiple functions such as PWM, ADC, DAC, I2C, I2S, SPI, etc ESP32-DevKitC V4 schematic (PDF)

    Niet op voorraad

    € 16,95

    Leden € 15,26

  • LILYGO T-Display-S3 ESP32-S3 Development Board (with Headers)

    LILYGO LILYGO T-Display-S3 ESP32-S3 Development Board (with Headers)

    Niet op voorraad

    LILYGO T-Display-S3 ESP32-S3 1,9-inch ST7789 LCD-scherm Development Board WiFi Bluetooth 5.0 draadloze module met 170x320 resolutie De T-Display-S3 is een ontwikkelbord met daarop als belangrijkste besturingschip de ESP32-S3. Hij is uitgerust met een 1,9-inch LCD-kleurenscherm en twee programmeerbare drukknoppen. Communicatie via de I8080-interface geschiedt met dezelfde lay-out als de T-Display. U kunt de ESP32S3 direct gebruiken voor USB-communicatie of programmeren. Specificaties MCU ESP32-S3R8 Dual-core LX7 microprocessor Draadloze communicatie Wi-Fi 802.11, BLE 5 + BT Mesh Programmeer platform Arduino IDE Micropython Flash 16 MB PSRAM 8 MB Detectie van batterijspanning IO04 Ingestelde functies Opstarten + resetten + IO14-knop LCD 1.9' diagonaal, TFT-kleurenscherm Drive chip ST7789V Resolutie 170(H)RGB x320(V) 8-Bit parallelle interface Werkspanning 3,3 V Ondersteuning STEMMA QT / Qwiic Connector JST-GH 1,25 mm 2-pins Downloads Pinout GitHub

    Niet op voorraad

    € 29,95

    Leden € 26,96

  • ESP-C3-12F-Kit Development Board with built-in 4 MB Flash

    Espressif ESP-C3-12F-Kit Development Board with built-in 4 MB Flash

    The ESP32-C3 chip has industry-leading low-power performance and radio frequency performance, and supports Wi-Fi IEEE802.11b/g/n protocol and BLE 5.0. The chip is equipped with a RISC-V 32-bit single-core processor with an operating frequency of up to 160 MHz. Support secondary development without using other microcontrollers or processors. The chip has built-in 400 KB SRAM, 384 KB ROM, 8 KB RTC SRAM, built-in 4 MB Flash also supports external Flash. The chip supports a variety of low power consumption working states, which can meet the power consumption requirements of various application scenarios. The chip's unique features such as fine clock gating function, dynamic voltage clock frequency adjustment function, and RF output power adjustable function can achieve the best balance between communication distance, communication rate and power consumption. The ESP-C3-12F module provides a wealth of peripheral interfaces, including UART, PWM, SPI, I²S, I²C, ADC, temperature sensor and up to 15 GPIOs. Features Support Wi-Fi 802.11b/g/n, 1T1R mode data rate up to 150 Mbps Support BLE5.0, does not support classic Bluetooth, rate support: 125 Kbps, 500 Kbps, 1 Mbps, 2 Mbps RISC-V 32-bit single-core processor, supports a clock frequency of up to 160 MHz, has 400 KB SRAM, 384 KB ROM, 8 KB RTC SRAM Support UART/PWM/GPIO/ADC/I²C/I²S interface, support temperature sensor, pulse counter The development board has RGB three-in-one lamp beads, which is convenient for the second development of customers. Support multiple sleep modes, deep sleep current is less than 5 uA Serial port rate up to 5 Mbps Support STA/AP/STA+AP mode and promiscuous mode Support Smart Config (APP)/AirKiss (WeChat) of Android and iOS, one-click network configuration Support serial port local upgrade and remote firmware upgrade (FOTA) General AT commands can be used quickly Support secondary development, integrated Windows and Linux development environment About Flash configuration ESP-C3-12F uses the built-in 4 MB Flash of the chip by default, and supports the external Flash version of the chip.

    € 14,95

    Leden € 13,46

  • Seeed Studio XIAO ESP32C3 Microcontroller Board

    Seeed Studio Seeed Studio XIAO ESP32C3

    Seeed Studio XIAO ESP32C3 has equipped a highly-integrated ESP32-C3 chip, built around a 32-bit RISC-V chip processor with a four-stage pipeline that operates at up to 160 MHz.The board equips highly-integrated ESP32-C3 SoC. The chip has been installed with a complete 2.4 GHz Wi-Fi subsystem which means it supports Station mode, SoftAP mode, SoftAP & Station mode, and promiscuous mode for multiple Wi-Fi applications. It works under an ultra-low power state, also supporting features of Bluetooth 5 and Bluetooth mesh. There are 400 KB SRAM & 4 MB Flash on the chip, allowing for more programming space, and bringing more possibilities to the IoT control scenarios.Applications Internet of Things Wearable devices Health monitoring Education Low-Power (LP) networking Rapid prototyping Features Outstanding RF performance: Powerful ESP32-C3 SoC and U.FL antenna provided that supports WiFi/Bluetooth connection over 100 m. Thumb-size Design: 21 x 17.5 mm overall dimension, portable and lightweight. Low power consumption: Lowest as 44 μA (deep sleep mode), with 4 working modes available. Onboard battery charge IC: Supports battery charging, great for various wearable scenarios and wireless IoT applications. Specifications Processor ESP32-C3 SoC RISC-V single-core 32-bit chip processor with a four-stage pipeline that operates at up to 160 MHz Wireless Complete 2.4 GHz Wi-Fi subsystem Bluetooth 5.0 / Bluetooth mesh On-chip Memory 400 KB SRAM & 4 MB Flash Interface 1x UART, 1x I²C, 1x I²S, 1x SPI, 11x GPIO (PWM), 4x ADC 1x Reset button, 1x Boot button Dimensions 21 x 17.5 mm Power Circuit operating voltage: 3.3 V @ 200 mA Charging current: 50 mA/100 mA Input voltage (VIN): 5 V Deep Sleep Power Consumption Deep Sleep Model: >44 μA Wi-Fi Enabled Power Consumption Active Model: <75 mA Modem-sleep Model: <25 mA Light-sleep Model: <4 mA BLE Enabled Power Consumption Modem-sleep Model: <27 mA Light-sleep Model: <10 mA Included 1x Seeed Studio XIAO ESP32C3 1x Antenna Downloads XIAO ESP32 Pinout ESP32-C3 Datasheet

    € 12,95

    Leden € 11,66

  • ESP32-DevKitC-32E

    Espressif ESP32-DevKitC-32E

    De ESP32-DevKitC is een entry-level ontwikkelbord met een klein formaat die deel uitmaakt van de ESP32 serie. Dit board heeft een veel opties voor randapparatuur. De ingebouwde ESP32-pinout is geoptimaliseerd voor probleemloos prototypen! Wifi & Bluetooth connectiviteit Dit compacte ontwikkelbord wordt aangestuurd door een ESP32-module. Deze integreert wifi en Bluetooth functies en biedt veel opties qua randapparatuur om snel te kunnen prototypen! Snel prototypen De ESP32-DevKitC biedt optimale RF-prestaties. U kunt direct aan de slag met het ontwerpen en ontwikkelen van toepassingen zonder u zorgen te hoeven maken over de RF-prestaties en het antenne-ontwerp. ESP32-DevKitC voldoet al aan uw basis systeemvereisten. Sluit gewoon de USB-kabel aan en u bent klaar om aan de slag te gaan! Flexibel en rijk aan functies De ESP32-DevKitC bevat het volledige arsenaal aan ondersteuning voor de ESP32-WROOM serie, de ESP32-WROVER serie en de ESP32-SOLO serie modules, inclusief een USB-UART-brug, reset- en opstartmodus knoppen, een LDO-regelaar en een micro-USB connector. Elke belangrijke GPIO is toegankelijk gemaakt voor de ontwikkelaar. Breadboard-vriendelijk De ESP32-DevKitC pinout is geoptimaliseerd om prototypen op een breadboard mogelijk te maken. De ingebouwde LDO-uitgang is van buiten af toegankelijk om extra externe elektronica van stroom te voorzien. De uitgangen voor de randapparatuur zijn netjes gegroepeerd voor probleemloos prototypen. Kenmerken Board ESP32-DevKitC-32E Gerelateerde module ESP32-WROOM-32E Flash geheugen 4 MB Antenne PCB Downloads Datasheet

    € 14,95

    Leden € 13,46

  • LILYGO TTGO T-Display ESP32 Development Board (16 MB)

    LILYGO LILYGO TTGO T-Display ESP32 Development Board (16 MB)

    LILYGO T-Display ESP32 WiFi and Bluetooth Module Development Board 1.14-inch LCD Control BoardSpecifications Chipset Espressif-ESP32 240 MHz Xtensa single-/dual-core 32-bit LX6 microprocessor Flash QSPI flash 16 MB SRAM 520 kB SRAM Button Reset USB to TTL CP2104 Modular interface UART, SPI, SDIO, I²C, LED PWM, TV PWM, I²S, IRGPIO, ADC, capacitor touch sensor, DACLNA pre-amplifier Display IPS ST7789V 1.14 Inch Working voltage 2.7-4.2 V Working current About 67 MA Sleep current About 350 uA Working temperature range -40°C ~ +85°C Size & Weight 51.52 x 25.04 x 8.54 mm (7.81 g) Power Supply USB 5 V/1 A Charging current 500 mA Battery 3.7 V lithium battery JST Connector 2-Pin 1.25 mm USB Type-C WiFi Standard FCC/CE-RED/IC/TELEC/KCC/SRRC/NCC (ESP32 chip) Protocol 802.11 b/g/n (802.11n, speed up to 150 Mbps) A-MPDU and A-MSDU polymerization, support 0.4μS Protection interval Frequency range 2.4~2.5 GHz (2400~2483.5 M) Transmit Power 22 dBm Communication distance 300 m Bluetooth Protocol Meet bluetooth v4.2BR/EDR and BLE standard Radio frequency With -97 dBm sensitivity NZIF receiver Class-1, Class-2 & Class-3 emitter AFH Audio frequency CVSD&SBC audio frequency Software Wi-Fi Mode Station/SoftAP/SoftAP+Station/P2P Security mechanism WPA/WPA2/WPA2-Enterprise/WPS Encryption Type AES/RSA/ECC/SHA Firmware upgrade UART download/OTA (Through network/host to download and write firmware) Software Development Support cloud server development /SDK for user firmware development Networking protocol IPv4, IPv6, SSL, TCP/UDP/HTTP/FTP/MQTT User Configuration AT + Instruction set, cloud server, Android/iOS app OS FreeRTOS Included 1x T-Display (16 MB) 1x Charging Cable 2x Pin

    € 24,95

    Leden € 22,46

  • LILYGO T-PicoC3 Development Board

    LILYGO LILYGO T-PicoC3 Development Board

    T-PicoC3 is LILYGO's first motherboard with dual MCUs – equipped with Raspberry Pi RP2040 and ESP32-C3 chip (supporting WiFi and Bluetooth).Specifications MCU RP2040 Dual ARM Cortex-M0+ Flash 4 MB Programming language C/C++, MicroPython Support machine leraning library TensorFlow Lite Onboard functions Buttons: IO06+IO07, battery power detection 1.14 inch ST7789V IPS LCD Resolution 135 x 240 Display Full-color TFT Interface 4-Wire SPI Power supply 3.3 V Operating temperature -20~70°C Dimensions 2.4 x 5.3 cm (W x H) DownloadsGitHub

    € 17,95

    Leden € 16,16

  • Makerfabs DIY ESP32 SmartClock Kit with Weather Forecasting

    Makerfabs Makerfabs DIY ESP32 SmartClock Kit with Weather Forecasting

    Niet op voorraad

    This is a soldering kit for the starters to learn soldering. After 1-2 hours soldering and assembly, and easy steps to set the Wifi name/password with a phone, you will get: A real-time clock, it will get the world real-time from the Network timing protocol, you can set your local time zone easily An Alarm clock, with loud noise An Online world weather forecaster, about the local temperature/weather, you can easily change/alter your address/cities without any re-programming To reduce the soldering difficulty, all the SMD parts have been soldered, you only need to solder the THT parts, and then set the Wifi network with a phone, and finally turn on the power to enjoy the success. Included ESP32 SmartClock kit mainboard Batch of capacitors & resistors/connectors Colorful LCD module Lipo battery Acrylic boards Nuts & screws Downloads User Manual Source code on GitHub

    Niet op voorraad

    € 34,95

    Leden € 31,46

  • Franzis Maker Kit für ESP32

    Franzis Franzis Maker Kit für ESP32

    Niet op voorraad

    Franzis Maker Kit für ESP32

    Niet op voorraad

    € 79,95

    Leden € 71,96

  • ESP Terminal (ESP32-S3 based Development Board with 3.5' Capacitive TFT Touch Display)

    Elecrow ESP Terminal (ESP32-S3 gebaseerd ontwikkel-board met 3,5' capacitief TFT-aanraakscherm)

    Niet op voorraad

    Deze ESP32-terminal is een microcontroller gebaseerd op de ESP32-master. Hij maakt gebruik van de Xtensa 32-bit LX7 dual-core processor met een klokfrequentie tot 240 MHz, ondersteunt 2,4 GHz Wi-Fi en Bluetooth 5 (LE), en kan gemakkelijk overweg met veelgebruikte toepassingsscenario's voor randapparatuur, zoals industriële besturing, detectie en verwerking van agrarische productieomgevingen, intelligente logistieke monitoring, smart home scenario's en nog veel meer. De ESP32-module heeft ook een parallel RGB-interface voor een 3,5 inch capacitief aanraakscherm met een resolutie van 320x480 voor een perfecte beeldweergave met een framerate van 60 FPS. De 4 Crowtail interfaces op de achterkant van deze terminal kunnen worden gebruikt met sensoren uit de Crowtail serie, plug-and-play, om snel en gemakkelijk meer interessante projecten creëren. Daarnaast is hij ook uitgerust met een SD-kaartsleuf voor uitgebreide opslag (SPI-aansluitingen) en een zoemer. Het ESP32 aanraakscherm ondersteunt ESP-IDF en Arduino IDE-ontwikkeling en is compatibel met Python/MicroPython/Arduino. Het ondersteunt ook LVGL, de populairste gratis en open-source embedded grafische bibliotheek om prachtige UI's te maken voor elke MCU, MPU en displaytype. Nu heeft het ook de officiële certificering van LVGL verkregen. Het LVGL-certificaat voor het board toont aan dat ze gemakkelijk gebruikt kunnen worden met LVGL en dat ze goede prestaties leveren voor UI-toepassingen. De onboard laadschakeling en de lithiumbatterij-interface kunnen de type-C voedingsinterface gebruiken om tegelijkertijd stroom te leveren en de batterij op te laden, waardoor er meer mogelijkheden zijn om outdoor scènes te verwezenlijken. Kenmerken Geïntegreerde ESP32-S3-module, die 2,4 GHz Wi-Fi en Bluetooth 5 (LE) ondersteunt.(LE) LCD 3,5 inch parallelle TFT-LCD met 320x480 resolutie Compatibel met Arduino/Python/MicroPython Volwassen softwareondersteuning, ondersteuning voor ESP-IDF en Arduino IDE-ontwikkeling Ondersteuning voor open-source grafische bibliotheek-LVGL Ondersteuning 1T1R-modus, datarate tot 150 Mbps, draadloze multimedia (WMM) Perfect beveiligingsmechanisme, ondersteuning voor AES-128/256, Hash, RSA, HMAC, digitale signaturen en veilig opstarten Ingebouwde oplaadchip en interface, gebruik type-C interface om op te laden Met 4 Crowtail interfaces (HY2.0-4P connector), plug-and-play met verschillende Crowtail sensoren Toepassingen Smarthome Industriële besturing Medische monitor Display voor huishoudelijke apparaten Logistics Monitoring Specificaties ESP32-S3-module met 16 MB flash en 8 MB PSRAM Wi-Fi protocol: 802.11b/g/n (802.11n tot 150 Mbps) Wi-Fi-frequentiebereik: 2,402-2,483 GHz Ondersteuning Bluetooth 5 Met 4 Crowtail interfaces (HY2.0-4P connector) en ingebouwde Micro TF kaartsleuf 3,5-inch TFT LCD RGB-scherm met 320x480 resolutie Driver chip: ILI9488 (16-bits parallelle lijn) Capacitieve aanraakpaneelcontroller IC FT6236-serie Bedrijfsspanning: DC 5 V-500 mA Slaapstroom: USB-voeding: 6,86 mA Lithium batterijvoeding: 3,23 mA LiPo Batterij Interface: PH2.0 Bedrijfstemperatuur: -10°C ~ 65°C Actief gebied: 73,63 x 49,79 mm (L x B) Afmetingen: 106 x 66 x 13 mm (L x B x H) Inbegrepen 1x 3.5-inch ESP RGB-beeldscherm met acryl behuizing 1x USB-C kabel Downloads Wiki Schematic Diagram 16 learning Lessons for LVGL Source code Lesson code LVGL Reference ESP32-S3 Datasheet ILI9488 Datasheet Capacitive Touch Display Data

    Niet op voorraad

    € 44,95

    Leden € 40,46

  • Elektor ESP32 Smart Kit

    Elektor Labs Elektor ESP32 Smart Kit

    Deze hardware kit is speciaal geprepareerd voor 'The Official ESP32 Book'. De kit bevat alle componenten die worden gebruikt in de projecten in dit boek. Met behulp van deze hardware kit is het gemakkelijk en leuk om de projecten in het boek te bouwen. Inbegrepen 1x ESP32 DevKitC 8x LED's (ROOD) 1x LED (GROEN) 2x drukknop 8x 330 ohm weerstanden 1x zoemer 1x RGB LED 1x TMP36 temperatuur sensor chip 1x DHT11 temperatuur en vochtigheid chip 1x MCP23017 (DIL 28 package) 1x LDR 1x BC108 (of een andere PNP) transistor 1x 7 segment LED 1x kleine microfoon module 1x I²C LCD 1x SG90 servo 1x 4x4 toetsenbordje 8x female-male jumpers 4x male jumpers 1x klein breadboardje

    € 59,95

    Leden € 53,96

  • LILYGO TTGO T-Journal ESP32 Camera Module Development Board (Fish-eye Lens)

    LILYGO LILYGO TTGO T-Journal ESP32 Camera Module Development Board (Fish-eye Lens)

    Het T-Journal is een goedkoop ESP32 Camera Development Board dat is voorzien van een OV2640 camera, een antenne, een 0,91 inch OLED display, enkele blootliggende GPIO's, en een micro-USB interface. Het maakt het gemakkelijk en snel om code te uploaden naar het bord.Specificaties Chipset Expressif-ESP32-PCIO-D4 240 MHz Xtensa single-/dual-core 32-bit LX6 microprocessor FLASH QSPI flash/SRAM, tot 4x 16 MB SRAM 520 kB SRAM KEY-reset, IO32 Display 0,91' SSD1306 Aan/uit-lampje rood USB naar TTL CP2104 Camera OV2640, 2 Megapixel Analoge servo stuurmotor On-board klok 40 MHz kristal oscillator Werkspanning 2,3-3,6 V Werkstroom ongeveer 160 mA Werkend temperatuurbereik -40℃ ~ +85℃ Afmeting 64,57 x 23,98 mm Voeding USB 5 V/1 A Laadstroom 1 A Batterij 3,7 V lithium batterij WiFi Standaard FCC/CE/TELEC/KCC/SRRC/NCC (ESP32-chip) Protocol 802.11 b/g/n/e/i (802.11n, snelheid tot 150 Mbps) A-MPDU en A-MSDU polymerisatie, ondersteuning 0,4 μS Beschermingsinterval Frequentiebereik 2,4 GHz~2,5 GHz (2400 M ~ 2483,5 M) Zendvermogen 22 dBm Communicatieafstand 300m Bluetooth Protocol voldoet aan bluetooth v4.2BR/EDR en BLE standaard Radio frequentie met -98 dBm gevoeligheid NZIF ontvanger Klasse-1, Klasse-2 & Klasse-3 emitter AFH Audio frequentie CVSD & SBC audio frequentie Software Wifi-modus Station/SoftAP/SoftAP+Station/P2P Veiligheidsmechanisme WPA/WPA2/WPA2-Enterprise/WPS Encryptie Type AES/RSA/ECC/SHA Firmware-upgrade UART-download/OTA (via netwerk/host om firmware te downloaden en te schrijven) Softwareontwikkeling Ondersteuning cloud server ontwikkeling /SDK voor gebruiker firmware ontwikkeling Netwerkprotocol IPv4, IPv6, SSL, TCP/UDP/HTTP/FTP/MQTT Gebruikersconfiguratie AT + instructieset, cloud server, Android/iOS app OS FreeRTOS Inbegrepen 1x ESP32-cameramodule (Fish-eye lens) 1x Wi-Fi-antenne 1x Stroomkabel DownloadsCamerabibliotheek voor Arduino

    € 32,95

    Leden € 29,66

  •  -20% ESP32-WROOM-32

    Espressif ESP32-WROOM-32

    The ESP-WROOM-32, measuring 25.2 mm x 18 mm only, contains the ESP32 SoC, flash memory, precision discrete components, and PCB antenna to provide outstanding RF performance in space-constrained applications. ESP-WROOM-32 is a powerful, generic Wi-Fi + BT + BLE MCU module that targets a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming and MP3 decoding. At the core of this module is the ESP32-D0WDQ6 chip. The chip embedded is designed to be scalable and adaptive. There are two CPU cores that can be individually controlled, and the clock frequency is adjustable from 80 MHz to 240 MHz. The user may also power off the CPU and make use of the low-power co-processor to monitor the peripherals for changes or crossing of thresholds constantly. ESP32 integrates a rich set of peripherals, ranging from capacitive touch sensors, Hall sensors, SD card interface, Ethernet, high-speed SPI, UART, I²S and I²C. The integration of Bluetooth, Bluetooth LE and Wi-Fi ensures that a wide range of applications can be targeted and that the module is future proof. Using Wi-Fi allows a vast physical range and direct connection to the internet through a Wi-Fi router while using Bluetooth allows the user to conveniently connect to the phone or broadcast low energy beacons for its detection. The sleep current of the ESP32 chip is less than 5 µA, making it suitable for battery powered and wearable electronics applications. ESP32 supports a data rate of up to 150 Mbps, and 20.5 dBm output power at the antenna to ensure the broadest physical range. As such the chip does offer industry-leading specifications and the best performance for electronic integration, range, power consumption, and connectivity.

    € 9,95€ 7,95

    Leden identiek

  • SparkFun MicroMod ESP32 Processor

    SparkFun SparkFun MicroMod ESP32 Processor

    Met de M.2 MicroMod connector is het aansluiten van uw ESP32 Processor een fluitje van een cent. Steek de edge-connector van uw processorbord in het M.2 slot en zet hem vast met een schroef (meegeleverd met alle Carrier Boards). Als u uw processor wilt vervangen door een gedegen draadloze optie, kijk dan zeker eens naar de MicroMod ESP32! De ESP32 bevat veel functionaliteit, waaronder de dual-core Tensilica LX6 microprocessor, 240MHz klokfrequentie, 520kB intern SRAM, geïntegreerde WiFi transceiver, geïntegreerde dual-mode Bluetooth, en hardware-encryptie (AES, SHA2, ECC, RSA-4096). Met dit MicroMod processorbord heb je toegang tot acht I/O-pinnen voor algemeen gebruik, analoge, digitale en PWM pinnen, alsook alle bekende interfaces zoals SPI, I2C, UART, en SDIO. Met 16 MB flash-opslag en een stroomopname van ongeveer 500µA in sleep-mode, is dit bord geschikt voor veel toepassingen. Eigenschappen Dual-core Tensilica LX6 microprocessor klokfrequentie tot 240 MHz 520 kB intern SRAM 128 Mbit / 16 MB flash storage Geïntegreerde 802.11 BGN WiFi transceiver dual-mode Bluetooth (classic and BLE) voedingsspanning 2,7 V tot 3,6 V 500µA stroom in sluimerstand 10-electrode capacitive touch support Hardware-accelerated encryption (AES, SHA2, ECC, RSA-4096) 1 x USB speciaal voor programmeren en debugging 1 x UART 2 x I2C 1 x SPI 7 x GPIO 2 x Digital Pins 2 x Analog Pins 2 x PWM Status LED VIN Level ADC

    € 18,95

    Leden € 17,06

  • "Makerfabs ESP32-S3 Parallel TFT with Touch 3.5\" ILI9488"

    Makerfabs MaTouch ESP32-S3 Parallel TFT 3.5" Touch Display (ILI9488)

    The ESP32-S3 Parallel TFT not only offers more SRAM and ROM (compared to the S2 version), but with Bluetooth 5.0 it is also suitable for applications such as local monitoring and controlling.The built-in LCD driver ILI9488 uses 16-bit parallel lines to communicate with ESP32-S3, the main clock can be up to 20 MHz, which makes the display smooth enough for video displays. With this display, you can create more IoT display projects.Features Controller: ESP32-S3-WROOM-1, PCB Antenna, 16 MB Flash, 2 MB PSRAM, ESP32-S3-WROOM-1-N16R2 Wireless: Wifi & Bluetooth 5.0 LCD: 3.5-inch TFT LCD Resolution: 480x320 Color: RGB LCD Interface: 16-bit parallel LCD Driver: ILI9488 Touch Panel: Capacitive Touch Panel Driver: FT6236 USB: Dual USB Type-C (one for USB-to-UART and one for native USB) UART to UART Chip: CP2104 Power Supply: USB Type-C 5.0 V (4.0 V~5.25 V) Button: Flash button and reset button Mabee Interface: 1x I²C, 1x GPIO Backlight Controller: Yes MicroSD: Yes Arduino support: Yes Type-C Power Delivery: Not supported Operation temperature: -40℃ to +85℃ Dimension: 66 x 84.3 x 12 mm Weight: 52 g Downloads ESP32-S3 Datasheet GitHub Wiki LVGL Demo Code

    € 59,95

    Leden € 53,96

  • ESP32-S3-BOX-3

    Espressif ESP32-S3-BOX-3

    Niet op voorraad

    De ESP32-S3-BOX-3 is gebaseerd op Espressif's ESP32-S3 Wi-Fi + Bluetooth 5 (LE) SoC, met AI versnellingsmogelijkheden. Als toevoeging op de 512 KB SRAM van de ESP32-S3 wordt de ESP32-S3-BOX-3 geleverd met 16 MB Quad flash en 16 MB Octaal PSRAM. De ESP32-S3-BOX-3 draait op Espressif's eigen spraakherkenningsframework, ESP-SR, dat gebruikers een offline AI spraakassistent biedt. Hij beschikt over far-field voice interaction, continue herkenning, wake-up interruption, en de mogelijkheid om meer dan 200 aanpasbare opdrachtwoorden te herkennen. De BOX-3 kan ook worden omgevormd tot een online AI chatbot met behulp van geavanceerde AIGC ontwikkelingsplatforms, zoals OpenAI. Aangestuurd door de krachtige ESP32-S3 SoC biedt de BOX-3 ontwikkelaars een kant-en-klare oplossing voor het maken van Edge AI en HMI toepassingen. De geavanceerde functies en mogelijkheden van de BOX-3 maken hem tot een ideale keuze voor diegenen in de IIoT industrie die Industrie 4.0 willen omarmen en traditionele fabrieksbesturingssystemen willen transformeren. De ESP32-S3-BOX-3 is de hoofd unit die wordt aangestuurd door de ESP32-S3-WROOM-1 module, die 2,4 GHz Wi-Fi + Bluetooth 5 (LE) biedt, evenals AI versnellingsmogelijkheden. In aanvulling op de 512 KB SRAM van de ESP32-S3 SoC wordt de module geleverd met een extra 16 MB Quad flash en 16 MB Octal PSRAM. Het board is uitgerust met een 2,4-inch 320 x 240 SPI-touchscreen (de 'rode cirkel' ondersteunt aanraking), twee digitale microfoons, een luidspreker, een 3-assige gyroscoop, een 3-assige accelerometer, een Type-C poort voor voeding en downloaden/debuggen, een high-density PCIe-connector die uitbreiding van de hardware mogelijk maakt, en ook drie functionele knoppen. Kenmerken ESP32-S3 WiFi + Bluetooth 5 (LE) 512 KB SRAM ESP32-S3-WROOM-1 16 MB Quad flash 16 MB Octaal PSRAM Inbegrepen ESP32-S3-BOX-3 Eenheid ESP32-S3-BOX-3 Sensor ESP32-S3-BOX-3 Dock ESP32-S3-BOX-3 Beugel ESP32-S3-BOX-3 Bread RGB LED-module en Dupont draden USB-C kabel Downloads GitHub Video's Unboxing The Next-generation Open-source Kit

    Niet op voorraad

    € 84,95

    Leden € 76,46

  • SparkFun Thing Plus (ESP32 WROOM)

    SparkFun SparkFun Thing Plus (ESP32 WROOM)

    Niet op voorraad

    The Thing doet alles van het aanzetten van een LED tot het posten van gegevens met het door u gekozen platform en wordt net als elke microcontroller geprogrammeerd. U kunt The Thing zelfs programmeren via de Arduino IDE door de updated ESP32 Arduino Core te installeren. De ESP32 Thing plus integreert een rijke set randapparatuur, uiteenlopend van capacitieve aanraaksensoren, Hall-sensoren, SD-kaart interface, Ethernet, hoge-snelheid SPI, UART, I2S en I2C. Dankzij de ESP32 WROOM module aan boord, beschikt de SparkFun Thing Plus over 16 MB flash geheugen, 520 kB intern SRAM, een geïntegreerde 802.11 BGN WiFi transceiver en dual-mode Bluetooth mogelijkheden, en een JST connector om een LiPo batterij aan te sluiten. Features Afmetingen: 2.30 x 0.90 Inches Xtensa® dual-core 32-bit LX6 microprocessor Tot 240MHz klokfrequentie 16 MB flash-geheugen 520kB intern SRAM Geïntegreerde 802.11 BGN WiFi transceiver Geïntegreerde dual-mode Bluetooth (klassiek en BLE) 2,3 V tot 3,6 V werkbereik 21 GPIO 8-elektrode capacitieve aanraakondersteuning Hardwareversnelde encryptie (AES, SHA2, ECC, RSA-4096) 2,5 µA diepe slaapstroom

    Niet op voorraad

    € 21,95

    Leden € 19,76

  • ESP32-S2-Saola-1R Development Board

    Espressif ESP32-S2-Saola-1R Development Board

    ESP32-S2-Saola-1R is a small-sized ESP32-S2 based development board. Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S2-Saola-1R on a breadboard.ESP32-S2-Saola-1R is equipped with the ESP32-S2-WROVER module, a powerful, generic Wi-Fi MCU module that has a rich set of peripherals. It is an ideal choice for a wide variety of application scenarios relating to Internet of Things (IoT), wearable electronics and smart home. The board a PCB antenna and features a 4 MB external SPI flash and an additional 2 MB SPI Pseudo static RAM (PSRAM).FeaturesMCU ESP32-S2 embedded, Xtensa® single-core 32-bit LX7 microprocessor, up to 240 MHz 128 KB ROM 320 KB SRAM 16 KB SRAM in RTC Wi­Fi 802.11 b/g/n Bit rate: 802.11n up to 150 Mbps A-MPDU and A-MSDU aggregation 0.4 µs guard interval support Center frequency range of operating channel: 2412 ~ 2484 MHz Hardware Interfaces: GPIO, SPI, LCD, UART, I²C, I²S, Camera interface, IR, pulse counter, LED PWM, TWAI (compatible with ISO 11898-1), USB OTG 1.1, ADC, DAC, touch sensor, temperature sensor 40 MHz crystal oscillator 4 MB SPI flash Operating voltage/Power supply: 3.0 ~ 3.6 V Operating temperature range: –40 ~ 85 °C Dimensions: 18 × 31 × 3.3 mm Applications Generic Low-power IoT Sensor Hub Generic Low-power IoT Data Loggers Cameras for Video Streaming Over-the-top (OTT) Devices USB Devices Speech Recognition Image Recognition Mesh Network Home Automation Smart Home Control Panel Smart Building Industrial Automation Smart Agriculture Audio Applications Health Care Applications Wi-Fi-enabled Toys Wearable Electronics Retail & Catering Applications Smart POS Machines

    € 22,95

    Leden € 20,66

  • PÚCA DSP ESP32 Development Board

    PÚCA DSP ESP32 Development Board

    PÚCA DSP is an open-source, Arduino-compatible ESP32 development board for audio and digital signal processing (DSP) applications with expansive audio-processing features. It provides audio inputs, audio outputs, a low-noise microphone array, an integrated test-speaker option, additional memory, battery-charge management, and ESD protection all on a small, breadboard-friendly PCB. Synthesizers, Installations, Voice UI, and More PÚCA DSP can be used for a wide range of DSP applications, including but not limited to those in the fields of music, art, creative technology, and adaptive technology. Music-related examples include digital-music synthesis, mobile recording, Bluetooth speakers, wireless line-level directional microphones, and the design of smart musical instruments. Art-related examples include acoustic sensor networks, sound-art installations, and Internet-radio applications. Examples related to creative and adaptive technology include voice user interface (VUI) design and Web audio for the Internet of Sounds. Compact, Integrated Design PÚCA DSP was designed for portability. When used with an external 3.7 V rechargeable battery, it can be deployed almost anywhere or integrated into just about any device, instrument, or installation. Its design emerged from months of experimentation with various ESP32 development boards, DAC breakout boards, ADC breakout boards, Microphone breakout boards, and audio-connector breakout boards, and – despite its diminutive size – it manages to provide all of that functionality in a single board. And it dos so without compromising signal quality. Specifications Processor & Memory Espressif ESP32 Pico D4 Processor 32-bit dual core 80 MHz / 160 MHz / 240 MHz 4 MB SPI Flash with 8 MB additional PSRAM (Original Edition) Wireless 2.4 GHz Wi-Fi 802.11b/g/n Bluetooth BLE 4.2 3D Antenna Audio Wolfson WM8978 Stereo Audio Codec Audio Line In on 3.5 mm stereo onnector Audio Headphone / Line Out on 3.5 mm stereo connector Stereo Aux Line In, Audio Mono Out routed to GPIO Header 2x Knowles SPM0687LR5H-1 MEMS Microphones ESD protection on all audio inputs and outputs Support for 8, 11.025, 12, 16, 22.05, 24, 32, 44.1 and 48 kHz sample rates 1 W Speaker Driver, routed to GPIO Header DAC SNR 98 dB, THD -84 dB (‘A’ weighted @ 48 kHz) ADC SNR 95 dB, THD -84 dB (‘A’ weighted @ 48 kHz) Line input impedance: 1 MOhm Line output impedance: 33 Ohm Form Factor and Connectivity Breadboard friendly 70 x 24 mm 11x GPIO pins broken out to 2.54 mm pitch header, with access to both ESP32 ADC channels, JTAG and capacitive touch pins USB 2.0 over USB Type C connector Power 3.7/4.2 V Lithium Polymer Rechargeable Battery, USB or external 5 V DC power source ESP32 and Audio Codec can be placed into low power modes under software control Battery voltage level detection ESD protection on USB data bus Downloads GitHub Datasheet Links Crowd Supply Campaign (includes FAQs) Hardware Overview Programming the Board The Audio Codec

    € 69,95

    Leden € 62,96

De ESP32 is een chip ontworpen voor mobiele, draagbare elektronica en Internet-of-Things (IoT) toepassingen. Het zit vol met alle state-of-the-art low-power functies die je nodig hebt, inclusief clock gating, meerdere power modes en dynamische power scaling.

Microcontroller met Wi-Fi en Bluetooth

De ESP32 is een sterk geïntegreerde chip die Wi-Fi en Bluetooth mogelijkheden combineert met een krachtige CPU en geheugen. Hij is ideaal voor toepassingen die een laag energieverbruik vereisen, zoals sensoren en draagbare apparaten.

ESP32 biedt twee CPU-kernen die afzonderlijk kunnen worden aangestuurd, geklokt tot 240 MHz, en elk voorzien van zijn eigen set randapparatuur. Naast de CPU-kernen beschikt de ESP32 over een speciale Tensilica LX6 microprocessor voor ultra-low power co-processing.

ESP32 module en toepassingen

De ESP32 module kan op verschillende manieren worden gebruikt. De meest populaire manieren om de ESP32 in een project te gebruiken is:

ESP32 als Arduino-compatibel bord

De ESP32 kan worden gebruikt als een Arduino-compatibel bord. Dit betekent dat u de Arduino IDE kunt gebruiken om toepassingen voor de ESP32 te ontwikkelen. De ESP biedt gebruikers de mogelijkheid om WiFi en Bluetooth verbindingen te maken.

ESP32 als zelfstandige microcontroller

De ESP32 kan ook als zelfstandige microcontroller worden gebruikt. Dit betekent dat u toepassingen voor de ESP32 kunt ontwikkelen zonder de Arduino IDE te gebruiken. De ESP32 is een goede keuze voor veel Internet of Things toepassingen. De ingebouwde WiFi en Bluetooth maken hem perfect voor draadloze toepassingen.

Internet of Things projecten met ESP32

De ESP32 is een geweldige keuze voor veel Internet of Things toepassingen. De ingebouwde WiFi en Bluetooth maken hem perfect voor draadloze toepassingen. De ESP32 is ook een zeer populaire microcontroller voor hobbyisten. Enkele populaire toepassingen voor de ESP32 zijn:

  • Domotica
  • IoT apparaten
  • Draagbare elektronica

Handleiding en boeken over ESP32

Wanneer je voor het eerst met ESP-modules werkt, is het fijn om uitleg te krijgen zodat je bekend raakt met de mogelijkheden en projecten met ESP32 techniek. The Official ESP32 Book is een boek waarin je als beginner stap voor stap wordt meegenomen. De Elektor ESP32 Smart Kit biedt beginners alles wat ze nodig hebben om de projecten uit het boek te kunnen volgen.

Login

Wachtwoord vergeten?

Heb je nog geen account?
Maak account aan