• 10% korting voor leden
  • Eigen tijdschrift
  • Eigen lab
Menu

Deze browser wordt niet langer ondersteund.

Gebruik de nieuwste versie van Google Chrome, Microsoft Edge, Mozilla Firefox, Opera of Apple Safari om alle webinhoud correct weer te geven.

USB-RS232 converter (FT231X BoB) - Bare PCB (180537-1)

USB-RS232 converter (FT231X BoB) - Bare PCB (180537-1)

Overzicht

Next generation USB/Serial Bridge/BoB using an FT231XQ and a Micro-USB connector. Pin headers allow access to all the pins of the FT231X.

VCCIO signal levels are in the range +1.8 V to +3.3 V but are 5 V tolerant.

Compatible with RS232, R485, and RS422 protocols.

Four additional configurable CBUS I/O pins available and an internal +3.3 V regulator with a maximum output current of 50 mA for powering external circuitry.

Overzicht

Next generation USB/Serial Bridge/BoB using an FT231XQ and a Micro-USB connector. Pin headers allow access to all the pins of the FT231X.

VCCIO signal levels are in the range +1.8 V to +3.3 V but are 5 V tolerant.

Compatible with RS232, R485, and RS422 protocols.

Four additional configurable CBUS I/O pins available and an internal +3.3 V regulator with a maximum output current of 50 mA for powering external circuitry.

€ 6,75
Niet-leden: Normale prijs € 7,50
Op voorraad
Levertijd: 3 werkdagen

Details

In 2011 we published a small PCB, FT232R USB/Serial Bridge/BOB (110553) with a USB-UART IC from FTDI, the FT232RQ. Here we present its successor with a cheaper version, an FT231XQ.

But there are some other changes too. Instead of connectors, alongside the PCB, normal pin headers are used that are mounted on the bottom side and make the PCB a little smaller when mounted, compared to the old BoB. An ESD protection device (D1) is added in the USB data signal lines for extra safety.

Despite less room for all parts to fit on the PCB, it is only a little over 2 mm longer. The FT231 has four configurable CBUS I/O pins, one less now. More importantly, however, the power supply for the I/O's VCCIO is only specified for +1.8 V to +3.3 but is 5 V tolerant for external UART logic running on +5 V. The +3.3 V internal regulator of the FT231 can deliver 50 mA to external circuitry.

The manufacturer FTDI has a utility to configure several settings, FTPROG. Such as the function of the CBUS pins. By default, CBUS1 and CBUS 2 are low-level outputs to drive receive and transmit LEDs, indicating data transfer on the USB bus. So, when receiving data through the UART, the TX LED lights up. If you prefer this the other way around, FTPROG can be used to change this. But be careful the chip can become unresponsive when wrong settings are programmed.

Some of the more important properties of the new BoB:

  • Micro-USB connector USB 2.0
  • Full Speed capable
  • VCCIO +1.8...+3.3 V (max. 4 V, 5 V input from UART logic tolerant)
  • +3.3 V regulator output, max. 50 mA
  • Data transfer 300 baud to 3 Mbaud
  • UART Compatible with RS232, RS485, and RS422
  • I/O pin output drive 4 mA - 16 mA
  • 4 configurable CBUS pins

Here you can find information regarding the EEPROM Programming Utility, the VCP Drivers and the D2XX Drivers

Specificaties

Meer informatie
SKU 18878
Fabrikant Elektor Labs
Print nummer 180537-1

Reviews (0)

Nog geen reviews. Wees de eerste die dit product reviewed.

Uw review voor USB-RS232 converter (FT231X BoB) - Bare PCB (180537-1)

Uw review voor USB-RS232 converter (FT231X BoB) - Bare PCB (180537-1)

Uw waardering