Raspberry Pi Accessories

109 producten


  • Official EU Power Supply for Raspberry Pi 4 (black)

    Raspberry Pi Foundation Official EU Power Supply for Raspberry Pi 4 (black)

    The Raspberry Pi USB-C power supply is designed specifically to power the latest Raspberry Pi 4 Model B computers. The power supply features a USB-C cable and is available in four different models to suit different international power sockets, and in two colors. Specifications Output Output voltage +5.1 V DC Minimum load current 0 A Nominal load current 3.0 A Maximum power 15.3 W Load regulation ±5 % Line regulation ±2 % Ripple & noise 120 mVp-p Rise time 100 ms maximum to regulation limits for DC outputs Turn-on delay 3000 ms maximum at nominal input AC voltage and full load Protection Short circuit protectionOvercurrent protectionOver temperature protection Efficiency 81% minimum (output current from 100%, 75%, 50%, 25%)72% minimum at 10% load Output cable 1.5 m 18AWG Output connector USB Type-C Input Voltage range 100 - 240 Vac (rated)96 - 264 Vac (operating) Frequency 50 / 60 Hz ± 3 Hz Current 0.5 A maximum Power consumption (no load) 0.075 W maximum Inrush current No damage shall occur, and the input fuse shall not blow Operating ambient temperature 0 - 40 °C

    € 9,95

    Leden identiek

  • microSD Card pre-Installed with NOOBS (32 GB)

    Raspberry Pi Foundation microSD-kaart voorgeïnstalleerd met Raspberry Pi OS (32 GB)

    With this microSD (32 GB) with pre-installed Raspberry Pi OS you can start using your Raspberry Pi right away. Just plug it in and get started!

    € 10,95

    Leden identiek

  •  -23% Elektor Raspberry Pi Buffer Board

    Elektor Labs Elektor Raspberry Pi Buffer Board

    When you experiment with the Raspberry Pi on a regular basis and you connect a variety of external hardware to the GPIO port via the header you may well have caused some damage in the past. The Raspberry Pi Buffer Board is there to prevent this! The board is compatible with Raspberry Pi Zero, 3, 4, 5 and 400. All 26 GPIOs are buffered with bi-directional voltage translators to protect the Raspberry Pi when experimenting with new circuits. The PCB is intended to be inserted in the back of Raspberry Pi< 400. The connector to connect to the Raspberry Pi is a right angled 40-way receptacle (2x20). The PCB is only a fraction wider. A 40-way flat cable with appropriate 2x20 headers can be connected to the buffer output header to experiment for instance with a circuit on a breadboard or PCB. The circuit uses four TXS0108E ICs by Texas Instruments. The PCB can also be put upright on a Raspberry Pi 3 or newer. Downloads Schematics Layout

    € 29,95€ 22,95

    Leden € 20,66

  • Official EU Power Supply for Raspberry Pi 4 (white)

    Raspberry Pi Foundation Official EU Power Supply for Raspberry Pi 4 (white)

    The Raspberry Pi USB-C power supply is designed specifically to power the latest Raspberry Pi 4 Model B computers. The power supply features a USB-C cable and is available in four different models to suit different international power sockets, and in two colors. Specifications Output Output voltage +5.1 V DC Minimum load current 0 A Nominal load current 3.0 A Maximum power 15.3 W Load regulation ±5 % Line regulation ±2 % Ripple & noise 120 mVp-p Rise time 100 ms maximum to regulation limits for DC outputs Turn-on delay 3000 ms maximum at nominal input AC voltage and full load Protection Short circuit protectionOvercurrent protectionOver temperature protection Efficiency 81% minimum (output current from 100%, 75%, 50%, 25%)72% minimum at 10% load Output cable 1.5 m 18AWG Output connector USB Type-C Input Voltage range 100 - 240 Vac (rated)96 - 264 Vac (operating) Frequency 50 / 60 Hz ± 3 Hz Current 0.5 A maximum Power consumption (no load) 0.075 W maximum Inrush current No damage shall occur, and the input fuse shall not blow Operating ambient temperature 0 - 40 °C

    € 9,95

    Leden identiek

  •  -29% Raspberry Pi 4 Case Fan

    Raspberry Pi Foundation Raspberry Pi 4 Case Fan

    Designed for overclockers and other power users, this fan keeps your Raspberry Pi 4 at a comfortable operating temperature even under heavy load. The temperature-controlled fan delivers up to 1.4 CFM of airflow over the processor, memory, and power management IC. The bundled heatsink (18 x 8 x 10 mm) with self-adhesive pad improves heat transfer from the processor. The Raspberry Pi 4 Case Fan works with Raspberry Pi 4 and the official Raspberry Pi 4 case.

    € 6,95€ 4,95

    Leden identiek

  • Official HDMI Cable for Raspberry Pi 4 (black, 1 m)

    Raspberry Pi Foundation Officiële HDMI-kabel voor Raspberry Pi (zwart, 1 m)

    De officiële Raspberry Pi micro HDMI naar HDMI (A/M) kabel (zwart, 1 m) ontworpen voor de Raspberry Pi 4 en 5. 19-pins HDMI type D(M) naar 19-pins HDMI type A(M) 1 m kabel (zwart) Vernikkelde stekkers Geschikt voor 4Kp60 In overeenstemming met RoHS 3 Mohm 300 VDC isolatie, bestand tegen VDC gedurende 0,1s

    € 6,95

    Leden identiek

  • Official HDMI Cable for Raspberry Pi 4 (white, 1 m)

    Raspberry Pi Foundation Officiële HDMI-kabel voor Raspberry Pi (wit, 1 m)

    De officiële Raspberry Pi micro HDMI naar HDMI (A/M) kabel ontworpen voor de Raspberry Pi 4 en 5. 19-pins HDMI type D(M) naar 19-pins HDMI type A(M) 1 m kabel (wit) Vernikkelde stekkers Geschikt voor 4Kp60 In overeenstemming met RoHS 3 Mohm 300 VDC isolatie, bestand tegen VDC gedurende 0,1s

    € 6,95

    Leden identiek

  • Waveshare Raspberry Pi 400 GPIO Header Adapter (2x 40 Pins)

    Waveshare Waveshare Raspberry Pi 400 GPIO Header Adapter (2x 40 Pins)

    The Waveshare 400 GPIO Header Extension is designed for Raspberry Pi 400 and provides a color-coded header and easy expansion. Features Designed for Raspberry Pi 400 Color-Coded Header Easy Expansion Included 1x PI400-GPIO-ADAPTER-B 1x Screws pack

    € 8,95

    Leden € 8,06

  •  -25% Heatsink Set for Raspberry Pi 4 (black)

    Kuongshun Heatsink Set for Raspberry Pi 4 (black)

    3 in 1 Heatsink Set Aluminium voor Raspberry Pi 4 en 5 Inhoud 1x 14x14x6 mm 1x 15x10x5 mm 1x 8,8x8,8x5 mm

    € 3,95€ 2,95

    Leden identiek

  • JOY-iT Aluminium Case for Raspberry Pi 4 with passive Cooling

    JOY-iT JOY-iT Aluminium Case for Raspberry Pi 4 with passive Cooling

    This aluminium case in a precious design is very robust and protects your Raspberry Pi 4 perfectly against outer influences. There are cut-outs for all interfaces to make them accessible. The channel milling at the top side serves as a heat sink and inside the housing the case is in direct contact with the CPU and the RAM to maximize cooling results. Features Color: Matt black (gun-metal black) Material: High-quality, cast aluminium Special Features: Channel milling which serves as a heatsink, cut outs for all interfaces, heatsink in contact with CPU and RAM of the Raspberry Pi for better cooling performance Dimensions: 91 x 65 x 34 mm Items delivered Aluminium case Screws Heat conduction pads

    € 14,95

    Leden € 13,46

  • Official Case for Raspberry Pi 4 (white/red)

    € 7,95

    Leden identiek

  • Official Case for Raspberry Pi 4 (black/grey)

    Raspberry Pi Foundation Official Case for Raspberry Pi 4 (black/grey)

    Officiële behuizing voor Raspberry Pi 4 (zwart/grijs)

    € 7,95

    Leden identiek

  • Raspberry Pi High Quality Camera Module

    Raspberry Pi Foundation Raspberry Pi High Quality Camera Module

    1 review

    De Raspberry Pi High Quality Camera heeft een hogere resolutie (12 megapixels, vergeleken met 8 megapixels) en gevoeligheid (een ongeveer 50% groter sensorgebied per pixel voor betere prestaties bij weinig licht) dan de bestaande Camera Module v2, en is ontworpen om te werken met verwisselbare lenzen met zowel C als CS lensvattingen. Andere lens uitvoeringen kunnen worden gebruikt met behulp van lens adapters van derden.Specificaties Sensor Sony IMX477R stacked, back-illuminated sensor12,3 megapixels7,9 mm sensor diagonaal1,55 x 1,55 μm pixel formaat Output RAW12/10/8, COMP8 Back focus Instelbaar (12,5–22,4 mm) Lens standaarden CS Mount C Mount (C/CS-adapter meegeleverd) IR cut filter Geïntegreerd Ribbon kabellengte 200 mm Statief houder 1/4'-20 Inbegrepen 1x Print met daarop een Sony IMX477 sensor 1x FPC kabel voor aansluiting op een Raspberry Pi 1x Gefreesde aluminium lensvatting met geïntegreerde statief houder en focus instelring 1x C/CS lensvatting adapter Niet inbegrepenLens met C/CS lensvatting

    € 59,95

    Leden identiek

  • Raspberry Pi Debug Probe

    Raspberry Pi Foundation Raspberry Pi Debug Probe

    The Raspberry Pi Debug Probe is an all-in-one USB-to-debug kit that provides all the necessary hardware and cables for easy, solderless, plug-and-play debugging. It features both a processor serial debug interface (by default the ARM Serial Wire Debug interface, but other interfaces can be supported) and an industry-standard UART interface. Both interfaces use the Raspberry Pi 3-pin debug connector. It is designed to make it easy to debug and program Raspberry Pi Pico and RP2040 with a range of host platforms including Windows, Mac, and typical Linux computers. While designed for use with Raspberry Pi products, the Debug Probe provides standard UART and CMSIS-DAP interfaces over USB, so it can also be used with other processors, or even just as a USB-to-UART cable. It works with OpenOCD and other tools that support CMSIS-DAP. The Debug Probe is based on Raspberry Pi Pico hardware and runs the open source Raspberry Pi Picoprobe software. The firmware is updated in the same way as Raspberry Pi Pico firmware, so it is easy to keep the unit up to date with the latest firmware, or to use custom firmware. Features USB to ARM Serial Wire Debug (SWD) port USB to UART bridge Compatible with the CMSIS-DAP standard Works with OpenOCD and other tools supporting CMSIS-DAP Open source, easily upgradeable firmware Specifications Dimensions: 22 x 32 mm Nominal I/O voltage: 3.3 V Operating temperature: -20°C to +70°C Included 1x Raspberry Pi Debug Probe 1x Plastic case 1x USB cable 3x Debug cables 3-pin JST connector to 3-pin JST connector cable 3-pin JST connector to 0.1-inch header (female) 3-pin JST connector to 0.1-inch header (male) Downloads Datasheet 3-pin Debug Connector Schematics Diagram

    € 14,95

    Leden identiek

  • Raspberry Pi for Radio Amateurs

    Raspberry Pi for Radio Amateurs

    Although much classical HF and mobile equipment is still in use by many amateurs, the use of computers and digital techniques has now become very popular among amateur radio operators. Nowadays, anyone can purchase a Raspberry Pi computer and run almost all amateur radio software on the ‘RPi’, which is slightly bigger than the size of a credit card. The RTL-SDR devices have become very popular among hams because of their very low cost and rich features. A basic system may consist of a USB-based RTL-SDR device (dongle) with a suitable antenna, an RPi computer, a USB-baased external audio input-output adapter, and software installed on the Pi. With such a simple setup it is feasible to receive signals from around 24 MHz to over 1.7 GHz. With the addition of a low-cost upconverter device, an RTL-SDR can easily and effectively receive the HF bands. This book is aimed at amateur radio enthusiasts, electronic engineering students, and anyone interested in learning to use the Raspberry Pi to build electronic projects. The book is suitable for the full range of beginners through old hands at ham radio. Step-by-step installation of the operating system is described with many details on the commonly used Linux commands. Some knowledge of the Python programming language is required to understand and modify the projects given in the book. Example projects developed in the book include a station clock, waveform generation, transistor amplifier design, active filter design, Morse code exerciser, frequency counter, RF meter, and more. The block diagram, circuit diagram, and complete Python program listings are given for each project, including the full description of the projects. Besides wide coverage of RTL-SDR for amateur radio, the book also summarizes the installation and use instructions of the following ham radio programs and software tools you can run on your Raspberry Pi: TWCLOCK, Klog, Gpredict, FLDIGI, DIRE WOLF, xcwcp, QSSTV, LinPsk, Ham Clock, CHIRP, xastir, and CQRLOG.

    € 34,95

    Leden € 31,46

  • Bijna uitverkocht Learning Python with Raspberry Pi

    Learning Python with Raspberry Pi

    Nog 1 op voorraad

    This book is about teaching the Python programming language using the Raspberry Pi 4 computer. The book makes an introduction to Raspberry Pi 4 and then teaches Python with the topics: variables, strings, arrays, matrices, tuples, lists, dictionaries, user functions, flow of control, printing, keyboard input, graphics, GUI, object oriented programming and many more topics.The book is aimed for beginners, students, practising engineers, hobbyists, and for anyone else who may want to learn to program in Python.The book includes many example programs and case studies. All the example programs and case studies have been tested fully by the author and are all working. The example programs aim to teach the various programming concepts of Python. The case studies cover the use of Python in the analysis and design of electronic circuits. Some of the case study topics are: Resistor colour code identification Resistive potential divider circuits Resistive attenuator design Zener diode voltage regulator design RC and RLC transient circuits Circuit frequency response Saving data on external memory stick Mesh and node circuit analysis using matrices Resonance in RLC circuits Transistor Biasing analysis Transistor amplifier design Design of active filters Interfacing hardware with GPIO, I²C and SPI Using Wi-Fi with Python and TCP/IP and UDP programs Using Bluetooth from Python Full program listings of all the programs used in the book are available at the Elektor website of the book. Readers should be able just to copy and use these programs in their Raspberry Pi projects without any modifications.

    Nog 1 op voorraad

    € 34,95

    Leden € 31,46

  • PiCAN 3 – CAN-Bus Board for Raspberry	Pi 4	with 3 A SMPS & RTC

    SK Pang Electronics PiCAN 3 - CAN-Bus Board for Raspberry Pi 4 with 3 A SMPS & RTC

    Kenmerken CAN v2.0B met 1 Mb / s Snelle SPI-interface (10 MHz) Standaard en uitgebreide data en externe frames CAN-verbinding via standaard 9-polige sub-D-connector of schroefaansluitingen Compatibel met OBDII-kabel Soldeerbrug om verschillende configuraties voor DB9-connector in te stellen 120 Ω terminator voorbereid Serieel LCD-scherm voorbereid LED-indicator Voorbereiding voor twee mini drukknoppen Vier bevestigingsgaten, voldoen aan de Pi Hat-standaard SocketCAN-stuurprogramma, wordt in de toepassing weergegeven als can0 RX-Interrupt op GPIO25 5 V / 3 A schakelende voeding voor de Raspberry Pi en accessoires van DB9 of schroefaansluiting Bescherming tegen verkeerde polariteit Schakelende voeding met hoog rendement 6 V tot 20 V ingangsbereik RTC met batterijback-up (batterij niet inbegrepen, CR1225-cel benodigd)Downloads User guide Schematic Driver installation Writing your own program in Python Python3 examples

    € 89,95

    Leden € 80,96

  • Official Raspberry Pi USB-C Adapter (black)

    Raspberry Pi Foundation Officiële Raspberry Pi USB-C adapter (zwart)

    This small adapter allows you to convert an existing micro USB power supply into a USB-C power supply.

    € 0,95

    Leden identiek

  • Makerfabs Jumper Wires Combo Pack

    Makerfabs Makerfabs Jumper Wires Combo Pack

    Niet op voorraad

    Met deze jumper draden (lengte: 20 cm) kunt u een Raspberry Pi of een Arduino met breadboards verbinden. Elke kabel bestaat uit 40 afzonderlijke draden/pinnen die ook weer van elkaar kunnen worden gescheiden. Inclusief 1x 40-pins female naar female 1x 40-pins mannelijk naar mannelijk 1x 40-pins mannelijk naar vrouwelijk

    Niet op voorraad

    € 6,95

    Leden € 6,26

  • Raspberry Pi Full Stack

    Raspberry Pi Full Stack

    Dit boek neemt u mee op een wervelende tour van full-stack web applicatie ontwikkeling met behulp van Raspberry Pi. U leert hoe u een applicatie vanaf de grond kunt opbouwen.U zult ervaring en kennis opdoen van technologieën waaronder: Het Linux-besturingssysteem en de opdrachtregel. De programmeertaal Python. De Raspberry Pi General Purpose Input Output pins (GPIOs). De Nginx webserver. Flask Python microkader voor webtoepassingen. JQuery en CSS voor het maken van gebruikersinterfaces. Omgaan met tijdzones. Creëren van grafieken met Plotly en Google Charts. Gegevensregistratie met Google Sheet. Applets ontwikkelen met IFTTT. Het beveiligen van uw applicatie met SSL. Sms-berichten ontvangen op je telefoon met Twilio. Dit boek leert u ook hoe u een draadloze Arduino sensor node op afstand kunt opzetten en er gegevens van kunt verzamelen. Uw Raspberry Pi web applicatie zal in staat zijn om Arduino node data te verwerken op dezelfde manier als het data verwerkt van zijn onboard sensor.Raspberry Pi Full Stack leert u veel vaardigheden die essentieel zijn voor het bouwen van Web- en Internet of Things-toepassingen.De applicatie die u in dit project zult bouwen, is een platform waarop u kunt uitbreiden. Dit is slechts het begin van wat je kunt doen met een Raspberry Pi en de software en hardware componenten die je zult leren kennen.Dit boek wordt ondersteund door de auteur via een speciale discussieruimte.

    € 39,95

    Leden € 35,96

  • Motor Control – Projects met Arduino & Raspberry Pi

    Motor Control - Projects met Arduino & Raspberry Pi

    Niet op voorraad

    Dit boek gaat over gelijkstroom elektromotoren en hun gebruik in Arduino en Raspberry Pi Zero W gebaseerde projecten. Het boek bevat veel geteste en werkende projecten waarbij elk project de volgende sub-rubrieken heeft: Titel van het project Beschrijving van het project Blok diagram schakelschema Projectassemblage Volledige programmalijst van het project Volledige beschrijving van het programma De projecten in het boek behandelen de standaard gelijkstroommotoren, stappenmotoren, servomotoren, en mobiele robots. Het boek is bedoeld voor studenten, hobbyisten en iedereen die geïnteresseerd is in het ontwikkelen van microcontroller-gebaseerde projecten met behulp van de Arduino Uno of de Raspberry Pi Zero W.Een van de leuke kenmerken van dit boek is dat het complete projecten geeft voor het op afstand besturen van een mobiele robot vanaf een mobiele telefoon, met zowel de Arduino Uno als de Raspberry Pi Zero W ontwikkelborden. Deze projecten zijn ontwikkeld met behulp van zowel Wi-Fi als de Bluetooth connectiviteit met de mobiele telefoon. Lezers moeten in staat zijn om een robot vooruit, achteruit, linksom of rechtsom te laten draaien door eenvoudige commando's te sturen vanaf een mobiele telefoon. De volledige programmalijsten van alle projecten en de gedetailleerde programmabeschrijvingen worden in het boek gegeven. Gebruikers zouden de projecten moeten kunnen gebruiken zoals ze worden gepresenteerd, of ze aan hun eigen behoeften moeten kunnen aanpassen.

    Niet op voorraad

    € 32,95

    Leden € 29,66

  • Official Raspberry Pi Mini-HDMI to HDMI Adapter Cable

    Raspberry Pi Foundation Official Raspberry Pi Mini-HDMI to HDMI Adapter Cable

    This short cable (10 cm) connects a standard HDMI cable to the Mini-HDMI port of a Raspberry Pi Zero.

    € 3,95

    Leden identiek

  •  -34% 40-pin GPIO Header for Raspberry Pi (color-coded)

    40-pin GPIO Header for Raspberry Pi (color-coded)

    This color-coded pin header is ideal for use with Raspberry Pi. All pins are color-coded with corresponding functions making prototyping and hacking easier. Specifications Suitable for all Raspberry Pi models with GPIO 2 pin rows with 20 pins each 2.54 mm pin spacing (pitch) Pin height: 3 / 6 mm Total height: approx. 11 mm Colors/Functions Orange = 3.3 V Red = 5 V Pink = I²C Purple = UART Blue = SPI Yellow = DNC Green = GPIO Black = GND (Ground)

    € 2,95€ 1,95

    Leden identiek

  • Official Raspberry Pi Mouse (white/red)

    Raspberry Pi Foundation Official Raspberry Pi Mouse (white/red)

    The official Raspberry Pi mouse is a three-button optical mouse which connects via a USB type A connector either to one of the USB ports on the keyboard or directly to a compatible computer. Three-button optical mouse Scroll wheel USB type A connector Ergonomic design for comfortable use Compatible with all Raspberry Pi products

    € 8,95

    Leden identiek

Login

Wachtwoord vergeten?

Heb je nog geen account?
Maak account aan