• 10% korting voor leden
  • Eigen tijdschrift
  • Eigen lab
Menu

Deze browser wordt niet langer ondersteund.

Gebruik de nieuwste versie van Google Chrome, Microsoft Edge, Mozilla Firefox, Opera of Apple Safari om alle webinhoud correct weer te geven.

MonoDAQ-U-X (1 kS/s) – Multifunctional USB Data Acquisition System

MonoDAQ-U-X (1 kS/s) – Multifunctional USB Data Acquisition System

Overzicht

Multifunctional, isolated USB data acquisition device for voltage, current, temperature, strain and resistance measurement

MonoDAQ-U-X is a fully isolated USB test & measurement device with full software support in DEWESoft data acquisition software. At the core of the measurement chain is a sigma-delta ADC with a maximum sample rate of 1 kS/s (16 bit) and a maximum resolution of 20 bit (100 S/s). 8 multifunctional front pins can be configured as analog or digital inputs or outputs.

Overzicht

Multifunctional, isolated USB data acquisition device for voltage, current, temperature, strain and resistance measurement

MonoDAQ-U-X is a fully isolated USB test & measurement device with full software support in DEWESoft data acquisition software. At the core of the measurement chain is a sigma-delta ADC with a maximum sample rate of 1 kS/s (16 bit) and a maximum resolution of 20 bit (100 S/s). 8 multifunctional front pins can be configured as analog or digital inputs or outputs.

€ 314,10
Niet-leden: Normale prijs € 349,00
Op voorraad
Levertijd: 3 werkdagen

Details

MonoDAQ-U-X is powered from the USB-C port on the backplane, therefore a single USB-C cable is needed for communication and power supply. Power and communication signals are isolated directly after the USB connector, which makes the microcontroller and the front end of the device fully galvanically isolated. Front-end connector features 8 multifunctional pins that can be configured as analog inputs or outputs or as digital inputs or outputs. Front-end is configured with the help of a channel setup table in DEWESoft software.

At the core of the measurement chain is a sigma-delta ADC with a maximum sample rate of 1 kS/s (16 bit) and a maximum resolution of 20 bit (100 S/s). If only one input channel is used, the signal is alias-free with a bandwidth of 0.4*fs (sampling frequency). If multiple analog input channels are used, the signals are multiplexed in front of the ADC. It is possible to select up to 8 single-ended voltage inputs and up to 4 differential voltage inputs. Half of the channels can have a high input range of 10 V while the other half is limited to 2 V since there is no voltage divider on those channels.

Specifications

  • Power and signal isolation between USB and front-end
  • Max. sample rate: 1 kS/s (16 bit), max. resolution: 20 bit (100 S/s)
  • Can connect up to 2 full bridge strain gauges or up to 4 thermocouples
  • Max. 4 differential or 8 single-ended voltage inputs
  • Current input with internal shunt (0.5 Ω)
  • Analog output (+/- 4 V, 14 bit, 50 kS/s)
  • Max. 8 digital inputs or outputs
  • 1 wire, I²C and UART interface on the front connector
  • Internal humidity sensor
  • Internal IMU (3-axial accelerometer and 3-axial gyroscope)

Typical applications

  • Embedded loT system power consumption measurement
  • Analog measurement front end for industrial machines and test benches
  • Strain measurement in industrial quality control
  • Industrial condition monitoring (voltage, temperature, current)
  • Precision measurement front end for single-board computers (Raspberry Pi, LattePanda etc.)
  • Precise laboratory power supply for board development

Synchronization between devices

Multiple MonoDAQ-U-X devices can be connected to the same PC by using a multiport USB hub. Synchronization between devices is ensured if all of the devices are connected to the same hub.

Software support

MonoDAQ-U-X is supported in DEWESoft X3 data acquisition software. On this page, you'll find some of the key functionalities of DEWESoft that are the most important ones for MonoDAQ users as well as additional links to DEWESoft page for in-depth info.

For custom applications, the device is also supported in Isotel IDM cross-platform software package based on Java. IDM can be installed on any operating system supporting Java and provides the basic interface to the device for configuration and data streaming. There is Python API available to access the device through IDM software.

What's in the box

  • 1x MonoDAQ-U-X (1 kS/s)
  • 1x USB-C to USB-A cable
  • 1x Push-in wire terminal
  • DEWESoft X3 LT Life License with FREE updates

Specificaties

Meer informatie
SKU 18767
Fabrikant MonoDAQ

Downloads

Video's

Reviews (0)

Nog geen reviews. Wees de eerste die dit product reviewed.

Uw review voor MonoDAQ-U-X (1 kS/s) – Multifunctional USB Data Acquisition System

Uw review voor MonoDAQ-U-X (1 kS/s) – Multifunctional USB Data Acquisition System

Uw waardering