Programmers & Debuggers

7 producten

  • The ?Art Kit – USB to UART-TTL Adapter

    The μArt Kit - USB to UART-TTL Adapter

    µArt heeft als doel veel voorkomende problemen van bestaande UART-adapters op te lossen door alle gebruikssituaties met één enkel apparaat te dekken, en een betrouwbare en robuuste oplossing te bieden waarop u gewoon kunt vertrouwen dat deze goed werkt. De μArt heeft alle pinnen en functies om verschillende toepassingen mogelijk te maken, beveiligingen om storingen te weerstaan of zelfs te voorkomen, het bieden van signaalintegriteit, en maatregelen om de bruikbaarheid te verbeteren. U hoeft zich geen zorgen te maken dat een klein foutje zal leiden tot een beschadiging van dure aangesloten apparaten.USB-UART converters worden gebruikt tijdens de eerste bouw van een printplaat, voor debugging en ontwikkeling, voor het flashen van firmware, voor het uitwisselen van operationele gegevens, voor het aansturen van randapparatuur, als servicepoorten in het veld, of als diagnostische interfaces tijdens analyse. Als je werkt of hackt in de elektronica engineering, computer engineering, of embedded systems vakgebieden, is een UART adapter hoogstwaarschijnlijk een van je essentiële tools.De µART zal van waarde zijn voor een breed publiek, van beginners tot ervaren ingenieurs.Professionals uit de industrie zullen het waarderen dat ze kunnen vertrouwen op de µART en dat ze zich kunnen concentreren op hun werk zonder te hoeven twijfelen aan hun gereedschap. Hobbyisten en studenten, die gemakkelijker fouten kunnen maken, zullen het prettig vinden dat de μArt storingen isoleert en schade aan omringende apparatuur voorkomt.U zult dit apparaat ook zeer nuttig vinden in diverse toepassingen samen met Raspberry Pi, Arduino of Espressif. Bovendien ondersteunt de μArt niet-standaard en aangepaste baudrates (zoals 128000), zodat u een snelle en betrouwbare instelling voor uw MCU kunt gebruiken.Basisfuncties Brede werkspanning van 1,8 tot 5,4 V, waardoor hij geschikt is voor de meeste projecten, of het nu gaat om single-board computers, microcontrollers, FPGA's, of low-power elektronica. RXD, TXD, DTR, RTS en CTS. Niet alleen bruikbaar voor basiscommunicatie, maar ook voor het flashen van diverse modules van Espressif en meerdere Arduino's, zoals de Pro Mini, Fio of Arduino Pro. Hardware handshaking zorgt voor een betrouwbare hoge-snelheid UART. Niet-standaard baudrate ondersteuning, zodat u het kunt gebruiken met standaard-klok microcontrollers en nog steeds een lage fout-rate hebben. Tot 3 Mbaud overdrachtsnelheid, de hoogste in de industrie. Dit is genoeg bandbreedte om ongecomprimeerde stereo-audio van hoge kwaliteit te streamen. Volledige galvanische scheiding, zelfs voor netspanning en hogere voltages. Er kan geen elektrische stroom vloeien tussen uw computer en het andere bord. Dit biedt veiligheid voor u en uw computer, terwijl het ook helpt om het geluidsniveau laag te houden. Omgekeerde polariteitsbeveiliging. De converter overleeft zelfs als u de voedingspinnen verwisselt. Overstroombeveiliging op IO-pennen. Per ongeluk een verkeerde IO verbinding gemaakt? Maak je geen zorgen, de μArt en je andere bord zijn beide veilig. Pullups op alle ingangen, zodat losgekoppelde pinnen geen rare dingen veroorzaken, zoals willekeurige vuilnisinvoer, een geruïneerde terminal-app of corrupte applicatiestatus. Roddelijke filtering. Elk IC in de converter is ontkoppeld met behulp van meerdere condensatoren, zowel lokaal als in bulk. De USB-signalen en de voeding worden gefilterd, en gevoelige pennen worden beschermd met RC-netwerken. ESD-bescherming op meerdere niveaus voor alle interfaces. ESD-schade is lastig omdat dingen na een ESD-gebeurtenis nog een tijdje kunnen lijken te werken, en daar heb je geen zichtbare vonken voor nodig. Voltage auto-sensing, wat betekent dat de converter automatisch de juiste spanningsniveaus zal gebruiken voor UART-communicatie. Platformoverschrijdende ondersteuning, met direct beschikbare en volwassen stuurprogramma's voor Windows, Linux, MacOS, en meer. Geschikt voor communicatie met ruisarme circuits, ondersteund door de filters, de isolatie en de zorgvuldige lay-out. GPIO-pinnen die u direct via USB kunt aansturen, parallel aan de UART-lijnen. Ze kunnen ook in de software worden geconfigureerd voor alternatieve functies (bijvoorbeeld TXDEN voor RS-485). Vier LED's, elk van een andere kleur om ze onmiddellijk te kunnen onderscheiden. Eén led licht op als de voeding is aangesloten, twee led's geven de RX/TX-activiteit aan, terwijl de laatste led is verbonden met een GPIO, zodat u visuele feedback krijgt over de status zonder speciale software op de hostcomputer. Vierwandige afgeschermde header beschermt tegen ESD door vingers en tegen kortsluiting door bungelende draden. Op maat gemaakte behuizing, professioneel en ergonomisch, met zowel mechanische als elektrische bescherming, en een cool transparant-transparant uiterlijk. Werkingssfeer van de leveringDe μArt wordt standaard geleverd in een op maat gemaakte plastic behuizing en biedt mechanische bescherming en draagt bij aan de elektrische bescherming. Bovendien worden de volgende kabels meegeleverd: Een hoogwaardige Micro USB-kabel van KabelDirekt Een gesplitste 'inktvis'-kabel die met een enkele connector (vrouwelijke uiteinden) met de μArt kan worden verbonden Een lint-jumper kabel (mannelijke uiteinden)

    € 64,95

    Leden € 58,46

  • Bijna uitverkocht Black Magic Probe V2.3 – JTAG/SWD ARM Microcontroller Debugger

    1 Bit Squared Black Magic Probe V2.3 - JTAG/SWD ARM Microcontroller Debugger

    Black Magic Probe V2.3 is a JTAG and SWD Adapter with a built-in GDB server used for programming and debugging ARM Cortex MCUs. Its the best friend of any ARM microcontroller developer.All proceeds from BMP hardware sales go directly into the continued development, maintenance and support of the Open-Source Black Magic Debug project.Black Magic Probe gets rid of intermediate programs like OpenOCD or STLink server. This makes the operation faster and more reliable. You just open your GNU Debugger (GDB) and select the virtual com port offered by BMP23 as your extended remote target. For a full description and how-to visit the project website.Features Wide target IO voltage range support, 1.7 V up to 5 V, thanks to VREF referenced level shifters Power switch allowing supply of 3.3 V to the target through the VREF pin Standard ARM-Cortex 0.05' pitch 10pin debug connector Aux UART capable of up to 2 MBaud Small size (4 x 2 x 1 cm) (1.3 x 0.6 x 0.45'), saving space in your field kit and allowing the use of the debugger in very tight spaces and enclosures Jumpers allowing the connection of the UART TX/RX pins to the JTAG/SWD connector resulting in a 'Unified debug' connector TraceSWO UART, decoding hardware support 16 MByte on board flash AUX connector for accessories Mechanical layout allowing easier use of enclosures and mounting into bigger systems. For example: automated pogopin test equipment, automated Hardware In The Loop (HITL) Continous Integration (CI) systems Improved layout, allowing further improvement of the Black Magic Debug firmware reliability and speed using hardware protocol acceleration Included 1x Black Magic Probe Mini V2.3 (BMP23) 1x JTAG Ribbon Cable 1x 0.1' Header Serial Cable 1x 10-pin ARM Cortexto7-pin Adapter 1x UART 0.1' Cable Dimensions 70 x 17 mm (1.3 x 0.6 in) 3.6 g (0.128 oz)

    € 114,95

    Leden € 103,46

  • SPIDriver

    Excamera Labs SPIDriver

    2 reviews

    SPIDriver shows you what’s happening on the SPI bus in real time, so no more guessing about the bus state. Its purpose is to make understanding the functioning of SPI hardware more intuitive. It's useful if you're into debugging hardware or simply introduce a class to SPI for the first time.You can directly control LEDs and LCD displays just by having SPIDriver and you won't have to deal with microcontrollers. It's also a useful tool for examining, backing up and cloning an SPI flash as well as reading and writing SPI flash in circuit.SPIDriver is also applicable if you want to drive, test and evaluate different displays.With the help of current and voltage monitoring you'll be able to detect electrical problems at early stages. Thanks to the included color coded wires you can hook SPIDriver up without much effort; no pinout diagram required. It includes 3.3 V and 5 V supplies for your device, plus a high-side current meter.SPIDriver comes with software to control it from: a GUI the command-line C and C++ using a single source file Python 2 and 3, using a module Technical features Live display shows you exactly what it’s doing all the time Sustained SPI transfers at 500 Kbps USB line voltage monitor to detect supply problems, to 0.01 V Target device high-side current measurement, to 5 mA Two auxiliary output signals, A and B Two dedicated power outlines: of 3.3 V and 5 V All signals color coded to match jumper colors All signals are 3.3 V, and are 5 V tolerant Uses an FTDI USB serial adapter, and Silicon Labs automotive-grade EFM8 controller Also reports uptime, temperature, and running CRC of all traffic All sensors and signals controlled using a simple serial protocol GUI, command-line, C/C++, and Python 2/3 host software provided for Windows, Mac, and Linux Details Maximum power out current: up to 470 mA Signal current: up to 10 mA Device current: up to 25 mA Dimensions: 61 mm x 49 mm x 6 mm Interface: USB 2.0, micro USB connector Contents (SPIDriver Core) 1x SPIDriver 1x Set of hookup jumpers

    € 49,95

    Leden € 44,96

  • Bijna uitverkocht I²CDriver

    Excamera Labs I²CDriver

    I²C is ubiquitous, you can find it in your phone, in embedded electronics, in all microcontrollers, Raspberry Pi and computer motherboards. It's applicable in a wide variety of cases, but the only downside is that it might be difficult to learn using it properly and to avoid painful debugging.This device makes it easier for you to understand what's going on inside, as I²CDriver has a clear logic-analyzer display of the signal lines plus a graphical decoding of the I²C traffic.In addition, it continuously displays an address map of all attached I²C devices, so as you connect a device, it lights up on the map.The current and voltage monitoring let you catch electrical problems early. The included color-coded wires make hookup quite easy; no pinout diagram is required. It includes a separate 3.3 V supply for your devices, a high-side current meter, and programmable pullup resistors for both I²C lines.Thanks to 3 I²C ports you can hook up multiple devices simultaneously without any effort. I²CDriver comes with software to control it from: a GUI the command-line C and C++ using a single source file Python 2 and 3, using a module You can control I²C hardware using the PC tools you’re familiar with and reduce the development time needed to get the device doing what you want it to.Calibrating devices like accelerometers, magnetometers, and gyroscopes is much simpler and faster when done directly on the PC through I²CDriver.Moreover, the built in display shows a heatmap of all active network nodes. So in an I²C network with multiple devices, you can see at a glance which ones are the most active.I²CDriver can dump all I²C traffic back to the PC. I²CDriver’s capture mode reliably records every bit to an exhaustive time-stamped log. This is really helpful for debug, analysis, and reverse-engineering. Supported formats include text, CSV, and VCD.Features Open hardware: the design, firmware and all tools are under BSD license Live display: shows you exactly what it’s doing all the time Fast transfer: sustained I²C transfers at 400 and 100 kHz USB power monitoring: USB line voltage monitor to detect supply problems, to 0.01 V Target power monitoring: target device high-side current measurement, to 5 mA I²C pullups: programmable I²C pullup resistors, with automatic tuning Three I²C ports: three identical I²C ports, each with power and I²C signals Jumpers: color coded jumpers included in each pledge level 3.3 output: output levels are 3.3 V, all are 5 V tolerant Supports all I²C features: 7- and 10-bit I²C addressing, clock stretching, bus arbitration Sturdy componentry: uses an FTDI USB serial adapter, and Silicon Labs automotive-grade EFM8 controller Usage reporting: reports uptime, temperature, and running CRC of all traffic Flexible control: GUI, command-line, C/C++, and Python 2/3 host software provided for Windows, Mac, and Linux Details Maximum power out current: up to 470 mA Device current: up to 25 mA Dimensions: 61 mm x 49 mm x 6 mm Computer interface: USB 2.0, micro USB connector Contents (I²CDriver Core) 1x I²CDriver 3x Set of hookup jumpers

    € 44,95

    Leden € 40,46

  • Sipeed RV-Debugger Plus JTAG + UART BL702

    Seeed Studio Sipeed RV-Debugger Plus JTAG + UART BL702

    BL702 is a highly integrated BLE and Zigbee combo chipset for IoT applications, contains 32-bit RISC-V CPU with FPU, frequency up to 144MHz, with 132KB RAM and 192 KB ROM, 1Kb eFuse, 512KB embedded Flash, USB2.0 FS device interface, and many other features. The firmware implement is inspired by 'open-ec', implemented by Sipeed teams and community developers. The firmware emulates an FT2232D device, default implement a JTAG+UART debugger, and can be implemented as a Dual-Serial Port debugger, a Bluetooth debugger, etc.

    € 8,95

    Leden € 8,06

  • Bijna uitverkocht USB ISP-Programmer Stick for AVR

    USB ISP-Programmer Stick for AVR

    Functions Write and read FLASH memory Write and read EEPROM Write and read Fusebits Write and read lock bits Chip erase Read OSCCAL register Compatible with Atmel ATtiny ATtiny12, ATtiny13, ATtiny15, ATtiny2313, ATtiny24, ATtiny25, ATtiny26, ATtiny44, ATtiny45, ATtiny84, ATtiny85, Attiny86, ATtiny261, ATtiny461, ATtiny861 Atmel ATmega Atmega88, ATmega103, ATmega128, ATmega1280, ATmega1281, ATmega16, ATmega161, ATmega162, ATmega163, ATmega164, ATmega168, ATmega169, ATmega32, ATmega324, ATmega325, ATmega328, ATmega3250, ATmega329x, ATmega48, ATmega64, ATmega640, ATmega644, ATmega645, ATmega6450, ATmega649x, ATmega8, ATmega8515, ATmega8535 Other ATmel Controllers AT90CAN128, AT90PWM2, AT90PWM2B, AT90PWM3, AT90PWM3B, AT90USB162, AT90USB646, AT90USB647, AT90USB1286, AT90USB1287

    € 29,95

    Leden € 26,96

  • Sale -20% Diamex EXA-Prog Package

    Diamex Diamex EXA-Prog Package

    EXA-Prog in housing EXA-Prog represents the new generation of ISP programmers, which are not limited to one specific microcontroller type, but support several different controller architectures and programming interfaces. Laser-cut plexiglass housing. Two built-in status LEDs signal the current state of the programmer. Features Function selection via DIP switch Signal level switchable, 3.3 V, 5 V Integrated high voltage generator for UPDI programming Automatic bit-rate adjustment in AVR-ISP mode Clock generator for AVR controller with fuse oscillator Button to reset the connected microcontroller 10-pin standard ISP connector Optional accessories: 10-pin to 6-pin adapter, ESP01 adapter Mini-USB connector for power supply and connection to PC Firmware can be updated via USB Windows PC tool for testing the signal levels at the programming port. Current consumption without microcontroller connected: approx. 30 mA Signal level at programming connector: 5 V (USB voltage) or 3.3 V Power supply for the external circuit: max. 300 mA (3.3 V), max. 500 mA (5 V) UPDI high voltage: approx. 12.3 V Weight: approx. 25 g Adapter 10-pin to 6-pin IS P and 6-pin UPDI The optimal solution for in-system programming (ISP) of AVR controllers. There are two different standards for the AVR-ISP interface, 6-pin and 10-pin. With this adapter kit, you can exchange the programming lines between both standards. For programming AVR-UPDI a 6-pin connector is also needed. This adapter supports 10-pin to 6-pin for AVR-ISP programming and 10-pin to 6-pin for AVR-UPDI programming. ESP adapter No buttons or switches are needed to activate the ESP bootloader. When ESPTOOL is used, the bootloader is automatically activated and the firmware is started after programming is complete. If another program is used that does not take over this control itself, the bootloader of the ESP can also be activated by a long press on the RESET button of the EXA-PROG and the firmware can be started by a short press after programming. AVR swivel lever High-quality module with swivel lever zero force socket for almost all AVR controllers in DIL package. No own board is required. DIL controllers are easy and fast to program. Can also be used for series production. The 10-pin ISP standard connector from Atmel is used. Additionally, pin 3 is designed as a clock connector if the controller is set to an external clock. 5x 10-pin ISP well connectors for AVR controller in DIL package Compatible with all signal levels Pin 3 for the clock generator High quality swing lever socket (zero force socket) for variable 4-18 mm pin spacing Included EXA-Prog in housing Adapter 10-pin to 6-pin ISP and 6-pin UPDI ESP adapter AVR swivel lever Mini-USB cable 10-pin connection cable 6-pin connection cable 6-pin jumper cable, male-female 6-pin jumper cable, female-female

    € 74,95€ 59,95

    Leden identiek

Login

Wachtwoord vergeten?

Heb je nog geen account?
Maak gratis een account aan en geniet van vele voordelen.