Arduino Uno is een open-source microcontroller bord gebaseerd op de ATmega328P. Het heeft 14 digitale in-/uitgangspinnen (waarvan er 6 kunnen worden gebruikt als PWM-uitgangen), 6 analoge ingangen, een 16 MHz keramische resonator (CSTCE16M0V53-R0), een USB-aansluiting, een voedingsaansluiting, een ICSP-header en een reset-knop. Het bevat alles wat nodig is om de microcontroller te ondersteunen; sluit het gewoon aan op een computer met een USB-kabel of voed het met een AC-to-DC adapter of batterij om aan de slag te gaan. Je kunt aan je Uno sleutelen zonder je al te veel zorgen te maken dat je iets verkeerd doet, in het ergste geval kun je de chip voor een paar dollar vervangen en opnieuw beginnen. 'Uno' betekent één in het Italiaans en werd gekozen om de release van Arduino Software (IDE) 1.0 te markeren. Het Uno-bord en versie 1.0 van Arduino Software (IDE) waren de referentieversies van Arduino, nu geëvolueerd naar nieuwere versies. De Uno board is de eerste in een reeks van USB Arduino boards, en het referentiemodel voor het Arduino platform; voor een uitgebreide lijst van huidige, voorbije of verouderde boards zie de Arduino index van boards. Specificaties Microcontroller ATmega328P Bedrijfsspanning 5 V Ingangsspanning (aanbevolen) 7-12 V Ingangsspanning (limiet) 6-20 V Digitale I/O-pinnen 14 (waarvan 6 met PWM-uitgang) PWM digitale I/O-pinnen 6 Analoge ingangspinnen 6 DC Stroom per I/O Pen 20 mA DC Stroom voor 3,3 V Pin 50 mA Flashgeheugen 32 KB (ATmega328P) waarvan 0,5 KB gebruikt door bootloader SRAM 2 KB (ATmega328P) EEPROM 1 KB (ATmega328P) Kloksnelheid 16 MHz LED_BUILTIN 13 Afmetingen 68,6 x 53,4 mm Gewicht 25 g
Features
RP2040 microcontroller chip ontwikkeld door Raspberry Pi in Engeland
Dual-core ARM Cortex M0+ processor, met een kloksnelheid tot 133 MHz
264 kB SRAM, en 2 MB on-board Flash geheugen
Castellated module maakt solderen direct op draagborden mogelijk
USB 1.1 host- en apparaatondersteuning
Energiezuinige slaap- en slapende modi
Programmering via slepen en neerzetten met behulp van massaopslag via USB
26x multifunctionele GPIO-pinnen
2x SPI, 2x I²C, 2× UART, 3x 12-bit ADC, 16x bestuurbare PWM-kanalen
Nauwkeurige klok en timer op de chip
Temperatuursensor
Versnelde drijvende-kommabibliotheken op de chip
8x programmeerbare IO (PIO) toestandsmachines voor aangepaste randapparatuur
Waarom een Raspberry Pi Pico?Zelf een microcontroller designen in plaats van een bestaande aanschaffen brengt een aantal voordelen met zich mee. Volgens Raspberry Pi zelf komt niet een van de bestaande beschikbare producten hiervoor in de buurt van hun prijs/performance verhouding.Deze Raspberry Pi Pico heeft Raspberry Pi tevens de mogelijkheid gegeven om zelf een aantal innovatieve en krachtige features toe te voegen. Deze features zijn nergens anders beschikbaar.Een derde reden is dat de Raspberry Pi Pico de mogelijkheid aan Raspberry Pi heeft gegeven om krachtige software rondom het product te creëren. Rondom deze software stack zit een uitgebreide documentatie set. De software en documentatie voldoen aan de hoge standaard van de kernproducten van Raspberry Pi (zoals de Raspberry Pi 400, Pi 4 Model B en Pi 3 Model A+).Voor wie is deze microcontroller geschikt?De Raspberry Pi Pico is voor zowel de gevorderde als beginnende gebruiker geschikt. Van het bedienen van een lichtscherm tot het bedienen van veel verschillende apparaten die je dagelijks gebruikt. Veel dagelijkse bewerkingen worden door deze technologie mogelijk gemaakt.Beginnende gebruikersDe Raspberry Pi Pico is programmeerbaar in de talen C en MicroPython en aanpasbaar voor een breed scala aan apparaten. Daarnaast is de Pico net zo eenvoudig in gebruik als het slepen en neerzetten van bestanden. Dit maakt deze microcontroller bij uitstek geschikt voor de beginnende gebruiker.Gevorderde gebruikersVoor de gevorderde gebruikers is het mogelijk om gebruik te maken van de uitgebreide randapparatuur van de Pico. De randapparatuur bestaat onder andere uit de SPI, I²C en acht programmeerbare I/O (PIO) -toestandsmachines.Wat is uniek aan de Raspberry Pi Pico?Uniek aan de Pico is dat deze is ontwikkeld door Raspberry Pi zelf. De RP2040 is voorzien van een dual-core Arm Cortex-M0 + processor met 264 KB intern RAM en ondersteuning voor maximaal 16 MB off-chip Flash.De Raspberry Pi Pico is verder uniek om verschillende redenen:
Het product heeft de hoogste prijs/kwaliteit verhouding in de markt van de microcontrollerboards
De Raspberry Pi Pico is door Raspberry Pi zelf ontwikkeld
De software stack rondom dit product is van hoogwaardige kwaliteit en komt in combinatie met een uitgebreide documentatie set.
Als u snel en gemakkelijk in de programmeerwereld wilt stappen, is de JOY-iT Mega 2560 R3 het board voor u. Dankzij de overvloed aan tutorials en instructies voor deze microcontroller online, zult u beginnen met programmeren zonder enige complicaties. Gebaseerd op een ATmega2560, die voldoende kracht biedt voor uw projecten en ideeën, JOY-iT Mega 2560 R3 heeft vele aansluitmogelijkheden met 54 digitale in- en uitgangen en 16 analoge ingangen. Om te beginnen met het programmeren van uw JOY-iT Mega 2560 R3, moet u de ontwikkelomgeving, en natuurlijk de drivers, op uw computer installeren. De Arduino IDE is het meest geschikt voor gebruik met de Mega 2560. Deze IDE is volledig compatibel met dit bord en biedt u elke driver die u nodig heeft voor een snelle start. Microcontroller ATmega2560 Kloksnelheid 16 MHz Bedrijfsspanning 5 V/DC Digitale I/O Pinnen 54 (waarvan 15 met PWM) Analoge ingangspinnen 16 Analoge Uitgangspinnen 15 Flashgeheugen 256 KB EEPROM 4 KB SRAM 8 KB Download JOY-iT Mega 2560 R3 Starter Kit hier.
ATOM U is a compact low-power consumption speech recognition IoT development kit. It adopts an ESP32 chipset, equipped with 2 low-power Xtensa 32-bit LX6 microprocessors with the main frequency of up to 240 MHz. Built-in USB-A interface, IR emitter, programmable RGB LED. Plug-and-play, easy to upload and download programs. Integrated Wi-Fi and digital microphone SPM1423 (I2S) for the clear sound record. suitable for HMI, Speech-to-Text (STT). Low-code development ATOM U supports UIFlow graphical programming platform, scripting-free, cloud push; Fully compatible with Arduino, MicroPython, ESP32-IDF, and other mainstream development platforms, to quickly build various applications. High integration ATOM U contains a USB-A port for programming/power supply, IR emitter, programmable RGB LED x1, button x1; Finely tuned RF circuit, providing stable and reliable wireless communication. Strong expandability ATOM U is easy access to M5Stack's hardware and software system. Features ESP32-PICO-D4 (2.4GHz Wi-Fi dual mode) Integrated programmable RGB LED and button Compact design Built-in IR emitter Expandable pinout and GROVE port Development platform: UIFlow MicroPython Arduino Specifications ESP32-PICO-D4 240MHz dual core, 600 DMIPS, 520KB SRAM, 2.4G Wi-Fi Microphone SPM1423 Microphone sensitivity 94 dB SPL@1 KHz Typical value: -22 dBFS Microphone signal-to-noise ratio 94 dB SPL@1 KHz, A-weighted Typical value: 61.4 dB Standby working current 40.4 mA Support input sound frequency 100 Hz ~ 10 KHz Support PDM clock frequency 1.0 ~ 3.25 MHz Weight 8.4 g Product size 52 x 20 x 10 mm Downloads Documentation
Features RP2040 microcontroller with 2 MB Flash Dual-core cortex M0+ at up to 133 MHz 264 KB multi-bank high performance SRAM External Quad-SPI Flash with eXecute In Place (XIP) High performance full-crossbar bus fabric 30 multi-function General Purpose IO (4 can be used for ADC) 1.8-3.3 V IO Voltage (NOTE. Pico IO voltage is fixed at 3.3 V) 12-bit 500 ksps Analogue to Digital Converter (ADC) Various digital peripherals 2× UART, 2× I²C, 2× SPI, 16× PWM channels 1× Timer with 4 alarms, 1× Real Time Counter 2× Programmable IO (PIO) blocks, 8 state machines total Flexible, user-programmable high-speed IO Can emulate interfaces such as SD Card and VGA Includes W5100S Supports Hardwired Internet Protocols: TCP, UDP, WOL over UDP, ICMP, IGMPv1/v2, IPv4, ARP, PPPoE Supports 4 Independent Hardware SOCKETs simultaneously Internal 16 KB Memory for TX/ RX Buffers SPI Interface Micro-USB B port for power and data (and for reprogramming the Flash) 40 pin 21x51 'DIP' style 1mm thick PCB with 0.1' through-hole pins also with edge castellations 3-pin ARM Serial Wire Debug (SWD) port 10 / 100 Ethernet PHY embedded Supports Auto Negotiation Full / Half Duplex 10 / 100 Based Built-in RJ45 (RB1-125BAG1A) Built-in LDO (LM8805SF5-33V) Downloads RP2040 Datasheet W5100S Datasheet Schematic & Part list & Gerber File C/C++ Examples CircuitPython Examples
De LoRa-E5 Development Kit is een gemakkelijk te gebruiken compacte ontwikkel-toolset waarmee je de krachtige eigenschappen van de LoRa-E5 STM32WLE5JC kunt ontdekken. Het bestaat uit een LoRa-E5 Dev Board, een antenne (EU868), een USB type C kabel, en een 2-AA 3 V batterijhouder.Het LoRa-E5 Dev Board is uitgerust met de LoRa-E5 STM32WLE5JC module, die de eerste combinatie is van LoRa RF en MCU chip in een kleine enkelvoudige chip, en is FCC en CE gecertificeerd. Hij is voorzien van een ARM Cortex-M4 kern en Semtech SX126X LoRa chip, ondersteunt zowel LoRaWAN als LoRa protocol op de wereldwijde frequentie en (G)FSK, BPSK, (G)MSK, en LoRa modulaties.Het LoRa-E5 ontwikkelingsboard heeft een zeer groot zendbereik, een extreem laag stroomverbruik en gebruiksvriendelijke interfaces.Het LoRa-E5 Dev Board heeft een long range zendbereik van LoRa-E5 tot 10 km in een open gebied. Het stroomverbruik van de on-board LoRa-E5 modules in sleep mode is slechts 2.1 µA (WOR mode). Hij is ontworpen volgens industriële normen met een brede werktemperatuur van -40℃ ~ 85℃, hoge gevoeligheid tussen -116.5 dBm ~ -136 dBm, en uitgangsvermogen tot +20.8 dBm bij 3.3 V.Het LoRa-E5 Dev board heeft ook veel interfaces. Om de volledige functionaliteit van de LoRa-E5 module te kunnen gebruiken heeft het LoRa-E5 Dev Board alle 28 pinnen van LoRa-E5 bedraad en voorziet het van vele interfaces waaronder Grove connectoren, RS-485 terminal, male/female pin headers waarmee je sensoren en modules met verschillende connectoren en gegevensprotocollen kunt aansluiten, zodat je tijd bespaart bij het solderen van draden. Je kunt het board ook gemakkelijk van stroom voorzien door de batterijhouder aan te sluiten met 2-AA batterijen, zodat je het tijdelijk kunt gebruiken zonder externe stroombron. Het is een gebruiksvriendelijke printplaat om gemakkelijk te testen en snel prototypes te maken.Specificaties
Afmetingen
LoRa-E5 Dev Board: 85.6 x 54 mm
Voedingsspanning
3-5 V (Battery) / 5 V (USB-C)
Uitgangsstroom
EN 3V3 / 5 V
Uitgangsvermogen
Tot +20.8 dBm bij 3.3 V
Frequentie
EU868
Protocol
LoRaWAN
Gevoeligheid
-116.5 dBm ~ -136 dBm
Interfaces
USB Type C / JST2.0 / 3x Grove (2x I²C/1x UART) / RS485 / SMA-K / IPEX
Modulatie
LoRa, (G)FSK, (G)MSK, BPSK
Werktemperatuur
-40℃ ~ 85℃
Stroomverbruik
LoRa-E5 module sleep current slechts 2.1 uA (WOR mode)
Inbegrepen
1x LoRa-E5 Dev Board
1x Antenne (EU868)
1x USB Type C kabel (20 cm)
1x 2-AA 3 V Batterijhouder
ESP32-S3-EYE is a small-sized AI development board. It is based on the ESP32-S3 SoC and ESP-WHO, Espressif’s AI development framework.
The ESP32-S3-EYE board consists of two parts: the main board (ESP32-S3-EYE-MB) features the ESP32-S3-WROOM-1 module, a 2-Megapixel camera, a SD card slot, a digital microphone, a USB port, and function buttons; and the sub board (ESP32-S3-EYE-SUB) integrates an LCD display. The main board and sub board are connected through pin headers.
ESP32-S3-EYE offers plenty of storage, with an 8 MB Octal PSRAM and a 8 MB flash. It also supports image transmission via Wi-Fi and debugging through a Micro-USB port.
Specifications
Camera
The camera OV2640 with 2 million pixels has a 66.5° field of view and a maximum resolution of 1600x1200. You can change the resolution when developing applications.
Module Power LED
The LED (green) turns on when USB power is connected to the board. If it is not turned on, it indicates either the USB power is not supplied, or the 5 V to 3.3 V LDO is broken. Software can configure GPIO3 to set different LED statuses (turned on/off, flashing) for different statuses of the board. Note: GPIO3 must be set up in open-drain mode. Pulling GPIO3 up may burn the LED.
Pin Headers
Connect the female headers on the sub board.
5 V to 3.3 V LDO
Power regulator that converts a 5 V supply into a 3.3 V output for the module.
Digital Microphone
The digital I²S MEMS microphone features 61 dB SNR and –26 dBFS sensitivity, working at 3.3 V.
FPC Connector
Connects the main board and the sub board.
Function Button
There are six function buttons on the board. Users can configure any functions as needed except for the RST button.
ESP32-S3-WROOM-1
The ESP32-S3-WROOM-1 module embeds the ESP32-S3R8 chip variant that provides Wi-Fi and Bluetooth 5 (LE) connectivity, as well as dedicated vector instructions for accelerating neural network computing and signal processing. On top of the integrated 8 MB Octal SPI PSRAM offered by the SoC, the module also comes with 8 MB flash, allowing for fast data access. ESP32-S3-WROOM-1U module is also supported.
MicroSD Card Slot
Used for inserting a MicroSD card to expand memory capacity.
3.3 V to 1.5 V LDO
Power regulator that converts a 3.3 V supply into a 1.5 V output for the camera.
3.3 V to 2.8 V LDO
Power regulator that converts a 3.3 V supply into a 2.8 V output for the camera.
USB Port
A Micro-USB port used for 5 V power supply to the board, as well as for communication with the chip via GPIO19 and GPIO20.
Battery Soldering Points
Used for soldering a battery socket to connect an external Li-ion battery that can serve as an alternative power supply to the board. If you use an external battery, make sure it has built-in protection circuit and fuse. The recommended specifications of the battery: capacity > 1000 mAh, output voltage 3.7 V, input voltage 4.2 V – 5 V.
Battery Charger Chip
1 A linear Li-ion battery charger (ME4054BM5G-N) in ThinSOT package. The power source for charging is the USB Port.
Battery Red LED
When the USB power is connected to the board and a battery is not connected, the red LED blinks. If a battery is connected and being charged, the red LED turns on. When the battery is fully charged, it turns off.
Accelerometer
Three-axis accelerometer (QMA7981) for screen rotation, etc.
The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1U, a general-purpose Wi-Fi + Bluetooth Low Energy MCU module that integrates complete Wi-Fi and Bluetooth Low Energy functions.
Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard.
Features
Module integrated: ESP32-S3-WROOM-1U-N8R8
Flash: 8 MB QD
PSRAM: 8 MB OT
SPI voltage: 3.3 V
Specifications
ESP32-S3-WROOM-1U
ESP32-S3-WROOM-1U is a powerful, generic Wi-Fi + Bluetooth Low Energy MCU module that has a rich set of peripherals. It provides acceleration for neural network computing and signal processing workloads. ESP32-S3-WROOM-1U comes with an external antenna connector.
5 V to 3.3 V LDO
Power regulator that converts a 5 V supply into a 3.3 V output.
Pin Headers
All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board for easy interfacing and programming.
USB-to-UART Port
A Micro-USB port used for power supply to the board, for flashing applications to the chip, as well as for communication with the chip via the on-board USB-to-UART bridge.
Boot Button
Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port.
Reset Button
Press this button to restart the system.
USB Port
ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 specification. The interface is used for power supply to the board, for flashing applications to the chip, for communication with the chip using USB 1.1 protocols, as well as for JTAG debugging.
USB-to-UART Bridge
Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.
RGB LED
Addressable RGB LED, driven by GPIO38.
3.3 V Power On LED
Turns on when the USB power is connected to the board.
Downloads
Pinout
De Portenta Cat. M1/NB IoT GNSS Shield kan van nut zijn bij het verbeteren van de connectiviteits-mogelijkheden van uw Portenta H7 toepassingen. Deze uitbreidingskaart maakt gebruik van de draadloze Cinterion TX62 module van Thales, ontworpen om aan efficiënte en energiezuinige IoT-toepassingen geoptimaliseerde bandbreedte en prestaties te bieden.De Portenta Cat. M1/NB IoT GNSS Shield is een uitbreiding op de krachtige edge-computing van de Portenta H7, om de ontwikkeling van asset tracking en remote monitoring mogelijk te maken in zowel industriële omgevingen, als ook in de landbouw, bij nutsbedrijven als bij smart city’s. De kaart biedt mobiele connectiviteit met zowel Cat. M1 als NB-IoT netwerken, met hierbij de optie om eSIM-technologie te gebruiken. Volg eenvoudig uw waardevolle goederen, in uw stad of wereldwijd, met een keuze uit GPS, GLONASS, Galileo of BeiDou.Functies
Connectiviteitsopties wijzigen zonder het board te hoeven wijzigen
Voeg NB-IoT, CAT. M1 en plaatsbepaling toe aan elk Portenta product
Optie om een kleine multiprotocol router (WiFi - BT + NB-IoT/CAT. M1) te maken
Verlaag de eisen qua communicatie-bandbreedte bij IoT-toepassingen aanzienlijk
Module met laag stroomgebruik
Ook compatibel met MKR-boards
Monitoring op afstandIndustriële en agrarische bedrijven kunnen gebruik maken van de Portenta Cat. M1/NB IoT GNSS Shield voor het op afstand monitoren van gasdetectoren, optische sensoren, machine alarmsystemen, biologische bestrijdingsapparatuur en meer.Technologieleveranciers die smart city oplossingen bieden kunnen de kracht en de betrouwbaarheid van de Portenta H7 combineren met de Portenta Cat. M1/NB IoT GNSS Shield, om data uit te wisselen en taken te automatiseren, en om zo een geoptimaliseerd gebruik van middelen en een verbeterde gebruikerservaring te realiseren.Bewaking van bedrijfsmiddelenVoeg monitoring opties toe aan uw bedrijfsmiddelen door de prestaties en edge computing functies van de boards uit de Portenta familie te combineren. De Portenta Cat. M1/NB IoT GNSS Shield is ideaal voor het bewaken van waardevolle goederen, en voor het monitoren van industriële machines en apparatuur.Specificaties
Connectiviteit
Cinterion TX62 draadloze module; NB-IoT - LTE CAT. M1; 3GPP Rel. 14 Compliant Protocol LTE Cat. M1/NB1/NB2; UMTS BANDEN: 1 / 2 / 3 / 4 / 5 / 8 / 12 (17) / 13 / 18 / 19 / 20 / 25 / 26 / 27 / 28 / 66 / 71 / 85; LTE Cat. M1 DL: max. 300 kbps, UL: max. 1,1 Mbps; LTE Cat. NB1 DL: max. 27 kbps, UL: max. 63 kbps; LTE Cat. NB2 DL: max. 124 kbps, UL: max. 158 kbps
Short messaging service (SMS)
Point-to-point Mobile Terminated (MT) en Mobile Originated (MO) Text Mode; Protocol Data Unit (PDU) Mode
Plaatsbepaling
GNSS capability (GPS/BeiDou/Galileo/GLONASS)
Overig
Embedded IPv4 en IPv6 TCP/IP stack access; Internet services: TCP server/client, UDP client, DNS, Ping, HTTP client, FTP client, MQTT client Secure Connection met TLS/DTLS Secure Boot
Dimensies
66 x 25,4 mm
Bedrijfstemperatuur
-40° C tot +85° C (-104° F tot 185°F)
Downloads
Datasheet
Schema
De Arduino Nano is een complete Arduino-compatibele single board computer die direct in een 32-pins socket, een breadboard of een bijbehorend carrier board kan worden gestoken. Het biedt de volledige Arduino-functionaliteit in zeer compacte afmetingen. Via de micro-USB-aansluiting kunt u het bord en de schakeling van stroom voorzien en gemakkelijk nieuwe programma's naar de controller overbrengen. Technische details Pin headers voor direct gebruik op het pinboard Ideaal voor prototyping Programmeerbaar via gratis Arduino IDE Aansluiting via mini-USB-aansluiting Chipset CH340G Interfaces: I²C, UART, SPI Afmeting: 45 x 18 mm Microcontroller ATmega328P-AU Bedrijfsspanning 5 V Flashgeheugen 32 KB (2 KB gebruikt voor Bootloader) SRAM 2 KB EEPROM 1 KB Digitale pinnen 22 (6 met PWM) Analoge pinnen 8 DC stroom per I/O Pen 40 mA Inputvoltage 7-12 V Downloads Datasheet Gebruiksaanwijzing
T-PicoC3 is LILYGO's first motherboard with dual MCUs – equipped with Raspberry Pi RP2040 and ESP32-C3 chip (supporting WiFi and Bluetooth).Specifications
MCU
RP2040 Dual ARM Cortex-M0+
Flash
4 MB
Programming language
C/C++, MicroPython
Support machine leraning library
TensorFlow Lite
Onboard functions
Buttons: IO06+IO07, battery power detection
1.14 inch ST7789V IPS LCD
Resolution
135 x 240
Display
Full-color TFT
Interface
4-Wire SPI
Power supply
3.3 V
Operating temperature
-20~70°C
Dimensions
2.4 x 5.3 cm (W x H)
DownloadsGitHub
PÚCA DSP is an open-source, Arduino-compatible ESP32 development board for audio and digital signal processing (DSP) applications with expansive audio-processing features. It provides audio inputs, audio outputs, a low-noise microphone array, an integrated test-speaker option, additional memory, battery-charge management, and ESD protection all on a small, breadboard-friendly PCB.Synthesizers, Installations, Voice UI, and MorePÚCA DSP can be used for a wide range of DSP applications, including but not limited to those in the fields of music, art, creative technology, and adaptive technology. Music-related examples include digital-music synthesis, mobile recording, Bluetooth speakers, wireless line-level directional microphones, and the design of smart musical instruments. Art-related examples include acoustic sensor networks, sound-art installations, and Internet-radio applications. Examples related to creative and adaptive technology include voice user interface (VUI) design and Web audio for the Internet of Sounds.Compact, Integrated DesignPÚCA DSP was designed for portability. When used with an external 3.7 V rechargeable battery, it can be deployed almost anywhere or integrated into just about any device, instrument, or installation. Its design emerged from months of experimentation with various ESP32 development boards, DAC breakout boards, ADC breakout boards, Microphone breakout boards, and audio-connector breakout boards, and – despite its diminutive size – it manages to provide all of that functionality in a single board. And it dos so without compromising signal quality.SpecificationsProcessor & Memory
Espressif ESP32 Pico D4 Processor
32-bit dual core 80 MHz / 160 MHz / 240 MHz
4 MB SPI Flash with 8 MB additional PSRAM (Original Edition)
Wireless 2.4 GHz Wi-Fi 802.11b/g/n
Bluetooth BLE 4.2
3D Antenna
Audio
Wolfson WM8978 Stereo Audio Codec
Audio Line In on 3.5 mm stereo onnector
Audio Headphone / Line Out on 3.5 mm stereo connector
Stereo Aux Line In, Audio Mono Out routed to GPIO Header
2x Knowles SPM0687LR5H-1 MEMS Microphones
ESD protection on all audio inputs and outputs
Support for 8, 11.025, 12, 16, 22.05, 24, 32, 44.1 and 48 kHz sample rates
1 W Speaker Driver, routed to GPIO Header
DAC SNR 98 dB, THD -84 dB (‘A’ weighted @ 48 kHz)
ADC SNR 95 dB, THD -84 dB (‘A’ weighted @ 48 kHz)
Line input impedance: 1 MOhm
Line output impedance: 33 Ohm
Form Factor and Connectivity
Breadboard friendly
70 x 24 mm
11x GPIO pins broken out to 2.54 mm pitch header, with access to both ESP32 ADC channels, JTAG and capacitive touch pins
USB 2.0 over USB Type C connector
Power
3.7/4.2 V Lithium Polymer Rechargeable Battery, USB or external 5 V DC power source
ESP32 and Audio Codec can be placed into low power modes under software control
Battery voltage level detection
ESD protection on USB data bus
Downloads
GitHub
Datasheet
Met de Portenta H7 Lite kunt u uw volgende smart project bouwen.Altijd al een geautomatiseerd huis gewild? Of een slimme tuin? Welnu, vanaf nu is dat eenvoudig met de Arduino IoT Cloud-compatible boards. Hiermee kunt u apparaten onderling koppelen, data visualiseren, en uw projecten vanuit de hele wereld beheren en delen.De Portenta H7 Lite lijkt erg op de Portenta H7, die gelijktijdig high-level code én realtime taken kan uitvoeren dankzij zijn twee processors. Het is bijvoorbeeld mogelijk om Arduino gecompileerde code gelijktijdig met MicroPython uit te voeren, en beide kernen met elkaar te laten communiceren. De H7 Lite is echter een goedkoper board, met configureerbare H7 functionaliteiten voor specifieke gebruikssituaties.Functies
Dual Core – Twee best-in-class processors in één, die in parallel taken uitvoeren
AI aan de edge – Krachtig genoeg om AI state machines te kunnen verwerken
Maatwerk - Het board kan makkelijk op maat geproduceert worden in grote volumes
Ondersteuning voor high-level programming (Micropython)
De Portenta H7 Lite biedt een tweevoudige functionaliteit: het kan functioneren als elke andere embedded microcontroller board, of als de hoofdprocessor van een embedded computer.Gebruik bijvoorbeeld het Portenta Vision Shield om uw H7 Lite om te toveren tot een industriële camera, die real-time machine learning algoritmen kan uitvoeren op live videofeeds. Omdat de H7 Lite eenvoudig met TensorFlow Lite gemaakte processen kan uitvoeren, kunt u een van de cores een computer vision algoritme laten berekenen, terwijl de andere low-level bewerkingen uitvoert, zoals het besturen van een motor of dienst doen als een gebruikersinterface.Oplossingen
High-end industriële machinerie
Laboratorium apparatuur
Computer vision
PLC's
Robotica controllers
Mission-critical apparatuur
High-speed booting computation (ms)
Twee parallelle coresDe hoofd-processor van de Portenta H7 Lite is de STM32H747 dual core, met hierin een Cortex-M7 op 480 MHz en een Cortex-M4 op 240 MHz. De twee cores communiceren via een Remote Procedure Call mechanisme, waarmee naadloos functies op de andere processor kunnen worden aangeroepen. Beide processors delen alle in-chip elektronica en kunnen de volgende toepassingen aan:
Arduino sketches op het ARM Mbed OS
Native Mbed toepassingen
MicroPython / JavaScript via een interpreter
TensorFlow Lite
Een nieuwe standaard voor pinoutsDe Portenta-familie voegt twee 80-pins high-density connectors toe aan de onderkant van het board. Dit zorgt voor schaalbaarheid naar een breed palet aan toepassingen, doordat u zo eenvoudig uw Portenta board kunt uitbreiden naar een board dat volledig aan uw wensen voldoet.USB-C multifunctionele connectorDe programming connector van het board is een USB-C poort, die ook kan worden gebruikt om het board van stroom te voorzien, of als een USB-hub, of om stroom te leveren aan OTG aangesloten apparaten.Arduino IoT CloudGebruik uw Portenta board via Arduino's IoT Cloud, een eenvoudige en snelle wijze om veilige communicatie te garanderen voor al uw verbonden Things.Specificaties
Microcontroller
STM32H747XI Dual Cortex-M7+M4 32-bit low power ARM MCU (datasheet)
Secure element (standaard)
Microchip ATECC608
Board voeding (USB/VIN)
5 V
Ondersteunde accu’s
Li-Po Single Cell, 3,7 V, minimaal 700 mAh (ingebouwde lader)
Werkspanning van het board
3,3 V
Stroomverbruik
2,95 μA in standby modus (back-up SRAM OFF, RTC/LSE ON)
Timers
22x timers en watchdogs
UART
4x poorten (2 met flow control)
Ethernet PHY
10 / 100 Mbps (alleen via de uitbreidingspoort)
SD-kaart
Interface voor SD-kaart connector (alleen via uitbreidingspoort)
Operationele temperatuur
-40 °C tot +85 °C
MKR headers
Gebruik een van de bestaande industriële MKR-uitbreidingen erop
High-density connectors
Twee 80-pins connectoren maken alle elektronica van het board bereikbaar voor andere apparaten
Camera interface
8-bit, tot 80 MHz
ADC
3x ADC's met een maximale resolutie van 16 bits (tot 36 kanalen, tot 3,6 MSPS)
DAC
2x 12-bits DAC (1 MHz)
USB-C
Host/device, high/full speed, stroomtoevoer
Downloads
Datasheet
Schema
Specificaties
ARM Cortex-M7 op 600 MHz
2 USB-poorten, beide 480 MBit/sec
2048K Flash (64K gereserveerd voor herstel & EEPROM emulatie)
1024K RAM (512K is strak gekoppeld)
2 I2S digitale audio
3 CAN Bus (1 met CAN FD)
1 S/PDIF digitale audio
3 SPI, alle met 16 woord FIFO
1 SDIO (4 bit) native SD
3 I2C, alle met 4 byte FIFO
7 serieel, alle met 4 byte FIFO
32 DMA-kanalen voor algemeen gebruik
31 PWM-pinnen
40 digitale pinnen, allen onderbreekbaar
14 analoge pinnen, 2 ADC's op chip
Random Nummer Generator
Cryptografische versnelling
Pixelverwerkingspijplijn
RTC voor datum/tijd
Periferische cross triggering
Programmeerbare FlexIO
Aan/uit-beheer van de stroomvoorziening
USB Host
Teensy 4.1's USB Host-poort maakt het mogelijk USB-apparaten aan te sluiten, zoals keyboards en MIDI muziekinstrumenten. Een 5-pins header en een USB Host kabel zijn nodig om een USB-apparaat aan te kunnen sluiten. U kunt ook een van deze kabels gebruiken om verbinding te maken met de USB-pinnen.
Geheugen
Aan de onderzijde van Teensy 4.1 zijn locaties om 2 geheugenchips te solderen. Het kleinere gebied is bedoeld voor een PSRAM SOIC-8 chip. De grotere locatie is bedoeld voor QSPI flash geheugen.
Power Consumption &; Management
Wanneer de Teensy 4.1 op 600 MHz draait, verbruikt hij ongeveer 100mA stroom en biedt hij ondersteuning voor het dynamisch schalen van de klok. In tegenstelling tot traditionele microcontrollers, waar het veranderen van de kloksnelheid verkeerde baudrates en andere problemen veroorzaakt, zijn de Teensy 4.1 hardware en Teensyduino's software ondersteuning voor Arduino timing functies ontworpen om dynamisch snelheidsveranderingen toe te staan. Seriële baudrates, audio streaming sample rates, en Arduino functies zoals delay() en millis(), en Teensyduino's uitbreidingen zoals IntervalTimer en elapsedMillis, blijven correct werken terwijl de CPU van snelheid verandert. Teensy 4.1 biedt ook een uitschakelfunctie. Door een drukknop aan te sluiten op de On/Off pin, kan de 3.3V voeding volledig worden uitgeschakeld door de knop vijf seconden ingedrukt te houden en weer ingeschakeld worden door kort op de knop te drukken. Als een knoopcel wordt aangesloten op VBAT, blijft Teensy 4.1's RTC ook de datum en tijd bijhouden terwijl de voeding is uitgeschakeld. Teensy 4.1 kan bovendien worden overgeklokt, tot ver boven 600MHz!
De ARM Cortex-M7 brengt veel krachtige CPU-functies naar een nauwkeurig real-time microcontroller-platform. De Cortex-M7 is een dual-issue superscaler processor, wat betekent dat de M7 twee instructies per klokcyclus kan uitvoeren, op 600MHz! Het gelijktijdig uitvoeren van twee instructies hangt natuurlijk af van de volgorde van de instructies en registers door de compiler. De eerste benchmarks hebben aangetoond dat C++ code gecompileerd door Arduino de neiging heeft om twee instructies ongeveer 40% tot 50% van de tijd te halen bij het uitvoeren van numeriek intensief werk met gebruik van gehele getallen en pointers. De Cortex-M7 is de eerste ARM microcontroller die branch prediction gebruikt. Bij M4, lussen en andere code die gebruik maken van vertakkingen, kan dit drie klokcycli duren. Bij M7, nadat een lus een paar keer is uitgevoerd, neemt de branch prediction die overhead weg, waardoor de branch-instructie in slechts één klokcyclus kan worden uitgevoerd.
Tightly Coupled Memory is een unieke eigenschap die de Cortex-M7 snelle single-cycle toegang tot het geheugen mogelijk maakt door gebruik te maken van een paar 64 bit brede bussen. De ITCM-bus biedt een 64-bits pad voor het ophalen van instructies. De DTCM-bus is een paar 32-bits paden, waardoor de M7 tot twee afzonderlijke geheugentoegangen in dezelfde cyclus kan uitvoeren. Deze extreem snelle bussen verschillen van M7's AXI hoofdbus, die toegang geeft tot ander geheugen en randapparatuur. 512 van het geheugen kan worden benaderd als strak gekoppeld geheugen. Teensyduino wijst automatisch uw Arduino-schetscode toe aan ITCM, en al het niet-malloc geheugengebruik aan de snelle DTCM tenzij u nieuwe sleutelwoorden toevoegt om de geoptimaliseerde standaard op te heffen. Geheugen dat niet wordt gebruikt op de strak gekoppelde bussen is geoptimaliseerd voor DMA toegang door randapparatuur. Omdat het grootste deel van M7's geheugentoegang wordt gedaan op de twee strak gekoppelde bussen, hebben krachtige DMA-gebaseerde randapparaten uitstekende toegang tot het niet-TCM geheugen voor zeer efficiente I/O.
De Cortex-M7 processor van Teensy 4.1 bevat een floating-point unit (FPU) die zowel 64-bit 'double' als 32-bit 'float' ondersteunt. Met M4's FPU op Teensy 3.5 & 3.6, en ook Atmel SAMD51 chips, is alleen 32-bit float hardware versneld. Elk gebruik van dubbele, dubbele functies zoals log(), sin(), cos() betekent trage software-geïmplementeerde wiskunde. Teensy 4.1 voert deze allemaal uit met FPU hardware.
Voor meer informatie, bekijk de officiële Teensy 4.1 pagina hier.
The AVR-IoT WA development board combines a powerful ATmega4808 AVR MCU, an ATECC608A CryptoAuthentication™ secure element IC and the fully certified ATWINC1510 Wi-Fi network controller – which provides the most simple and effective way to connect your embedded application to Amazon Web Services (AWS). The board also includes an on-board debugger, and requires no external hardware to program and debug the MCU.Out of the box, the MCU comes preloaded with a firmware image that enables you to quickly connect and send data to the AWS platform using the on-board temperature and light sensors. Once you are ready to build your own custom design, you can easily generate code using the free software libraries in Atmel START or MPLAB Code Configurator (MCC).The AVR-IoT WA board is supported by two award-winning Integrated Development Environments (IDEs) – Atmel Studio and Microchip MPLAB X IDE – giving you the freedom to innovate with your environment of choice.Features
ATmega4808 microcontroller
Four user LED’s
Two mechanical buttons
mikroBUS header footprint
TEMT6000 Light sensor
MCP9808 Temperature sensor
ATECC608A CryptoAuthentication™ device
WINC1510 WiFi Module
On-board Debugger
Auto-ID for board identification in Atmel Studio and Microchip MPLAB X
One green board power and status LED
Programming and debugging
Virtual COM port (CDC)
Two DGI GPIO lines
USB and battery powered
Integrated Li-Ion/LiPo battery charger
Met de NodeMCU-ESP32 is comfortabel prototyping mogelijk met eenvoudige programmering via Luascript of de Arduino IDE en het breadboard-compatibele ontwerp. Dit bord heeft 2.4 GHz dual-mode Wifi en een BT draadloze verbinding. Bovendien zijn een 512 KB SRAM en een 4 MB geheugen geïntegreerd op het microcontroller ontwikkelbord. Het bord heeft 21 pinnen voor interface verbindingen, waaronder I²C, SPI, UART, DAC en ADC.Specificaties
TypeType
ESP32
Processor
Tensilica LX6 Dual-Core
Klokfrequentie
240 MHz
SRAM
512 kB
Geheugen
4 MB
Draadloze Lan
802.11 b/g/n
Frequentie
2.4 GHz
Bluetooth
Klassiek / LE
Data-interfaces
UART / I²C / SPI / DAC / ADC
Werkingssspanning
3,3 V (bruikbaar via 5 V microUSB)
Werkingsstemperatuur
-40°C - 125°C
Afmetingen
48 x 26 x 11.5 mm
Gewicht
10 g
Downloads
Handleiding
Frequency
2.4 GHz
Bluetooth
Classic / LE
Data Interfaces
UART / I²C / SPI / DAC / ADC
Operating Voltage
3.3 V (operable via 5 V microUSB)
Operating Temperature
–40°C – 125°C
Dimensions
48 x 26 x 11.5 mm
Weight
10 g
DownloadsManual
De Arduino MKR Zero is een ontwikkel-board voor muziekmakers! Met een SD-kaart connector en speciale SPI-interfaces (SPI1) kunt u muziekbestanden afspelen zonder extra hardware.De MKR Zero brengt u de kracht van een Zero in het kleinere formaat van de MKR uitvoering. Het MKR Zero board is een prima educatief tool om 32-bits applicatieontwikkeling mee te leren. Hij heeft een ingebouwde SD-kaart connector en speciale SPI-interfaces (SPI1) waarmee u muziekbestanden kunt afspelen zonder extra hardware! Het board wordt bestuurd door Atmel's SAMD21 MCU, die een 32-bits ARM Cortex M0+ core heeft.Het board bevat alles wat nodig is om de microcontroller te ondersteunen. Sluit hem simpelweg met een micro-USB kabel aan op een computer, of voed hem met een Li-Po accu. Omdat er een verbinding zit tussen de accu en de analoog converter van het board kan de accuspanning ook worden gemonitord.Specificaties
Microcontroller
SAMD21 ARM Cortex-M0+ 32-bit low power
Board voeding (USB/VIN)
5 V
Ondersteunde accu’s
Li-Po single cell, 3,7 V, minimaal 700 mAh
Gelijkstroom voor 3,3 V pin
600 mA
Gelijkstroom voor 5 V pin
600 mA
Werkspanning van het board
3,3 V
Digitale I/O pinnen
22
PWM pinnen
12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - of 18 -, A4 - of 19)
UART
1
SPI
1
I²C
1
Analoge ingangspinnen
7 (ADC 8/10/12-bits)
Analoge uitgangspinnen
1 (DAC 10-bits)
Externe interrupts
10 (0, 1, 4, 5, 6, 7, 8, A1 - of 16-, A2 - of 17)
Gelijkstroom per I/O-pin
7 mA
Flash geheugen
256 KB
Flash-geheugen voor bootloader
8 KB
SRAM
32 KB
EEPROM
Nee
Kloksnelheid
32.768 kHz (RTC), 48 MHz
LED_BUILTIN
32
Downloads
Datasheet
Eagle-bestanden
Schema
Fritzing
Pinout
Het Uno R3 bord is de perfecte microcontroller voor diegenen die de programmeerwereld willen betreden zonder enige poespas. De ATMega328 microcontroller geeft u genoeg power voor uw ideeën en projecten. Het Uno-bord heeft een USB type B aansluiting zodat u het gemakkelijk kunt gebruiken met programma's - uiteraard via de bekende programmeeromgeving Arduino IDE. U kunt hem via de USB-poort op de stroombron aansluiten of als alternatief zijn eigen stroomaansluiting gebruiken. Let op:De CH341 driver moet vooraf worden geïnstalleerd, zodat het Uno-bord wordt herkend door de Arduino IDE. Microcontroller ATmega 328 Kloksnelheid 16 MHz Bedrijfsspanning 5 V Invoerspanning 5-10 V Digitale I/O pinnen 14 met PWM 6 USB 1x SPI 1x I²C 1x ICSP 1x Flashgeheugen 32 KB EEPROM 1x
The OKdo E1 is an ultra-low-cost Development Board based on the NXP LPC55S69JBD100 dual-core Arm Cortex-M33 microcontroller. The E1 board is perfect for Industrial IoT, building control and automation, consumer electronics, general embedded and secure applications. Features Processor with Arm TrustZone, Floating Point Unit (FPU) and Memory Protection Unit (MPU) CASPER Crypto co-processor to enable hardware acceleration for certain asymmetric cryptographic algorithms PowerQuad Hardware Accelerator for fixed and floating point DSP functions SRAM Physical Unclonable Function (PUF) for key generation, storage and reconstruction PRINCE module for real-time encryption and decryption of flash data AES-256 and SHA2 engines Up to Nine Flexcomm interfaces. Each Flexcomm interface can be selected by software to be a USART, SPI, I²C, and I²S interface USB 2.0 High-Speed Host/Device controller with on-chip PHY USB 2.0 Full-Speed Host/Device controller with on-chip PHY Up to 64 GPIOs Secure digital input/output (SD/MMC and SDIO) card interface Specifications LPC55S69JBD100 640kbyte flash microcontroller In-built CMSIS-DAP v1.0.7 debugger based on LPC11U35 Internal PLL support up to 100MHz operation, 16MHz can be mounted for full 150MHz operation. SRAM 320kB 32kHz crystal for real-time clock 4 user switches 3-colour LED User USB connector 2-off 16-way expansion connectors UART over USB virtual COM port
The PIC-IoT WA Development Board combines a powerful PIC24FJ128GA705 MCU, an ATECC608A CryptoAuthentication™ secure element IC and the fully-certified ATWINC1510 Wi-Fi network controller – which provides the most simple and effective way to connect your embedded application to Amazon Web Services (AWS). The board also includes an on-board debugger, and requires no external hardware to program and debug the MCU.Out of the box, the MCU comes preloaded with firmware that enables you to quickly connect and send data to the AWS platform using the on-board temperature and light sensors. Once you are ready to build your own custom design, you can easily generate code using the free software libraries in MPLAB Code Configurator (MCC).The PIC-IoT WA Board is supported by MPLAB X IDE.Features
PIC24FJ128GA705 microcontroller128 KB Flash Memory & 16 KB SRAM
ATWINC1510 WiFi ModuleSingle-band 2.4GHz b/g/n IoT Network Controller, Pre-certified Module
ATECC608A CryptoAuthentication™ deviceProtected Storage for 16 Keys, SHA256, AES-CCM, ECDH (Elliptic Curve Diffie-Hellman), ECDSA
Other Board Features
Four Status LED’s
Blue LED indicates a connection to Wi-Fi network
Green LED indicates a connection to the AWS servers
Yellow LED indicates a packet of sensor data has been successfully published to the AWS MQTT servers
Red LED indicates an Error occurred
Two mechanical buttons
TEMT6000 Light sensor
MCP9808 Temperature sensor
mikroBUS header to interface to MikroElekronika click Boards™
Auto-ID for board identification in Microchip MPLAB X
On-board Debugger
Programming and debugging
Virtual COM port (CDC)
One logic analyzer channel (DGI GPIO)
USB and battery powered
Integrated Li-Ion/LiPo battery charger
De Arduino MKR NB 1500 stelt u in staat om uw volgende slimme project te bouwen.Altijd al een geautomatiseerd huis gewild? Of een slimme tuin? Welnu, vanaf nu is dat eenvoudig met de Arduino IoT Cloud-compatible boards. Hiermee kunt u apparaten onderling koppelen, data visualiseren, en uw projecten vanuit de hele wereld beheren en delen. Of u een beginner bent of een professional, we kunnen u een breed scala aan abonnementen bieden om u alle ondersteuning te geven die u nodig heeft.Voeg met de MKR NB 1500 Narrowband-communicatie toe aan uw project. Dat is een prima optie voor apparaten op afgelegen locaties zonder internetverbinding, of in situaties waarin geen stroom beschikbaar is zoals bij implementaties in het veld, meetsystemen op afstand, apparaten op zonne-energie of andere uitzonderlijke situaties.De hoofdprocessor van het board is de energiezuinige ARM Cortex-M0 32-bit SAMD21, net als in andere boards binnen de Arduino MKR-familie. De Narrowband-connectiviteit wordt uitgevoerd met een module van u-blox, de SARA-R410M-02B, een energiezuinige chipset die werkt op de verschillende banden van de IoT LTE-spectra. Bovendien wordt een veilige communicatie gegarandeerd met de Microchip ECC508 crypto-chip. Daarnaast bevat de kaart een acculader en een connector voor een externe antenne.Dit board is ontworpen voor wereldwijd gebruik en biedt connectiviteit op LTE Cat M1/NB1 banden 1, 2, 3, 4, 5, 8, 12, 13, 18, 19, 20, 25, 26, 28. Operators die diensten aanbieden in dit deel van het spectrum zijn onder andere: Vodafone, AT&T, T-Mobile USA, Telstra en Verizon.SpecificatiesDe Arduino MKR NB 1500 is gebaseerd op de SAMD21 microcontroller.
Microcontroller
SAMD21 Cortex-M0+ 32-bit low power ARM MCU (datasheet)
Radiomodule
u-blox SARA-R410M-02B (datasheet summary)
Secure element
ATECC508 (datasheet)
Board voeding (USB/VIN)
5 V
Ondersteunde accu’s
Li-Po Single Cell, 3,7 V, minimaal 1500 mAh
Bedrijfsspanning van het circuit
3,3 V
Digitaal en/of pinnen
8
PWM pinnen
13 (0 .. 8, 10, 12, 18 / A3, 19 / A4)
UART
1
SPI
1
I²C
1
Analoge ingangspennen
7 (ADC 8/10/12-bits)
Analoge uitgangspennen
1 (DAC 10-bits)
Externe interrupts
8 (0, 1, 4, 5, 6, 7, 8, 16 / A1, 17 / A2)
Gelijkstroom per I/O-pin
7 mA
Flash-geheugen
256 KB (intern)
SRAM
32 KB
EEPROM
Nee
Kloksnelheid
32.768 kHz (RTC), 48 MHz
LED_BUILTIN
6
USB
Full-speed USB device met embedded host
Antenne versterking
2 dB
Carrier frequentie
LTE-banden 1, 2, 3, 4, 5, 8, 12, 13, 18, 19, 20, 25, 26, 28
Vermogensklasse (radio)
LTE Cat. M1 / NB1: Klasse 3 (23 dBm)
Data snelheid (LTE M1 halp-duplex)
UL 375 kbps / DL 300 kbps
Data snelheid (LTE NB1 full-duplex)
UL 62,5 kbps / DL 27,2 kbps
Actieve regio
Multi regio
Locatiebepaling van het board
GNSS via modem
Stroomverbruik (LTE M1)
min 100 mA / max 190 mA
Stroomverbruik (LTE NB1)
min 60 mA / max 140 mA
SIM-kaart
MicroSIM (niet inbegrepen bij het board)
Dimensies
67,6 x 25 mm
Gewicht
32 gr
Downloads
Eagle-bestanden
Schema
Pinout
ESP32-C3-DevKitM-1 is een ontwikkelingsboard voor beginners, gebaseerd op de ESP32-C3-MINI-1, een module die zijn naam dankt aan zijn kleine afmetingen. Dit board beschikt over volledige Wi-Fi en Bluetooth LE functies.
De meeste I/O-pinnen op de ESP32-C3-MINI-1 module zijn uitgesplitst naar de pin headers aan beide zijden van dit board voor eenvoudige interfacing. Ontwikkelaars kunnen randapparatuur aansluiten met jumper draden of de ESP32-C3-DevKitM-1 op een breadboard monteren.
Specificaties
ESP32-C3-MINI-1
ESP32-C3-MINI-1 is een universele Wi-Fi en Bluetooth LE combo-module die wordt geleverd met een PCB-antenne. Het hart van deze module is de ESP32-C3FN4, een chip met een embedded flash van 4 MB. Omdat de flash geïntegreerd is in de ESP32-C3FN4 chip, in plaats van in de module, heeft de ESP32-C3-MINI-1 een kleiner formaat.
5 V naar 3.3 V LDO
Spanningsregelaar die een 5 V voeding omzet in 3,3 V.
5 V Power On LED
Schakelt in wanneer de USB-voeding op het board wordt aangesloten.
Pin Headers
Alle beschikbare GPIO-pinnen (behalve de SPI-bus voor flash) zijn uitgesplitst naar de pin headers op het board. Zie voor details Header Block.
Boot knop
Downloadknop. Als je Boot ingedrukt houdt en dan op Reset drukt, start de modus Firmware Download voor het downloaden van firmware via de seriële poort.
Micro-USB poort
USB-interface. Voeding voor het board en de communicatie-interface tussen een computer en de ESP32-C3FN4 chip.
Reset knop
Druk op deze knop om het systeem opnieuw op te starten.
USB-to-UART Bridge
Single USB-UART bridge chip biedt overdrachtssnelheden tot 3 Mbps.
RGB LED
Adresseerbare RGB LED, aangestuurd door GPIO 8.
Downloads
ESP32-C3 Datasheet
ESP32-C3-MINI-1 Datasheet
ESP32-C3-DevKitM-1 Schematic
ESP32-C3-DevKitM-1 PCB Layout
ESP32-C3-DevKitM-1 Dimensions
LILYGO T-Display RP2040 Raspberry Pi Module 1.14-inch LCD Development Board This board is based on a Raspberry Pi Pico RP2040 with Dual Cortex-M0+ and 4 MB Flash memory. It is equipped with a 1.14-inch full color IPS display. The ST7789V display has a resolution of 135 x 240 pixels and is connected via the SPI interface. Specifications MCU RP2040 Dual ARM Cortex M0+ Flash 4 MB Bus interfaces 2x UART, 2x SPI, 2x I²C, 6x PWM Programming language C/C++, MicroPython Support machine learning library TensorFlow Lite Onboard functions Buttons: IO06+IO07, battery power detection TFT Display 1.14-inch ST7789V IPS LCD Resolution 135 x 240, full color Interface 4-Wire SPI interface Operating temperature -20°C ~ +70°C Working power supply 3.3 V Connector JST-GH 1.25 mm 2-pin Included LILYGO T-Display RP2040 Unsoldered headers JST cable Downloads Pinout GitHub
The SparkFun RP2040 mikroBUS Development Board is a low-cost, high performance platform with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. Besides the Thing Plus or Feather PTH pin layout, the board also includes a microSD card slot, 16 MB (128 Mbit) flash memory, a JST single cell battery connector (with a charging circuit and fuel gauge sensor), an addressable WS2812 RGB LED, JTAG PTH pins, four (4-40 screw) mounting holes, our signature Qwiic connectors, and a mikroBUS socket. The mikroBUS standard was developed by MikroElektronika. Similar to Qwiic and MicroMod interfaces, the mikroBUS socket provides a standardized connection for add-on Click boards to be attached to a development board and is comprised of a pair of 8-pin female headers with a standardized pin configuration. The pins consist of three groups of communications pins (SPI, UART and I²C), six additional pins (PWM, Interrupt, Analog input, Reset and Chip select), and two power groups (3.3 V and 5 V). The RP2040 is supported with both C/C++ and MicroPython cross-platform development environments, including easy access to runtime debugging. It has UF2 boot and floating-point routines baked into the chip. While the chip has a large amount of internal RAM, the board includes an additional 16 MB of external QSPI flash memory to store program code. The RP2040 contains two ARM Cortex-M0+ processors (up to 133 MHz) and features: 264 kB of embedded SRAM in six banks 6 dedicated IO for SPI Flash (supporting XIP) 30 multifunction GPIO: Dedicated hardware for commonly used peripherals Programmable IO for extended peripheral support Four 12-bit ADC channels with internal temperature sensor (up to 0.5 MSa/s) USB 1.1 Host/Device functionality Features (SparkFun RP2040 mikroBUS Dev. Board) Raspberry Pi Foundation's RP2040 microcontroller 18 Multifunctional GPIO Pins Four available 12-bit ADC channels with internal temperature sensor (500kSa/s) Up to eight 2-channel PWM Up to two UARTs Up to two I²C buses Up to two SPI buses Thing Plus (or Feather) Pin Layout: 28 PTH Pins USB-C Connector: USB 1.1 Host/Device functionality 2-pin JST Connector for a LiPo Battery (not included): 500mA charging circuit 4-pin JST Qwiic Connector LEDs:
PWR - Red 3.3V power indicator
CHG - Yellow battery charging indicator
25 - Blue status/test LED (GPIO 25)
WS2812 - Addressable RGB LED (GPIO 08) Buttons: Boot Reset JTAG PTH Pins 16MB QSPI Flash Memory µSD Card Slot mikroBUS Socket Dimensions: 3.7' x 1.2' Four Mounting Holes: 4-40 screw compatible Downloads Schematic Eagle Files Board Dimensions Hookup Guide Qwiic Info Page GitHub Hardware Repository