Zoekresultaten voor "intelligente acc"
Ulanzi TC001 ESP32-gebaseerde Smart Pixel Clock
De Ulanzi TC001 is een LED pixelklok bestaande uit 256 individueel adresseerbare RGB LED's (8x32), met ingebouwde accu, zoemer, licht-, temperatuur- en vochtigheidssensor. De geïntegreerde oplaadbare accu biedt een gebruikstijd van maximaal 5 uur. De WiFi-verbinding met de klok wordt gemaakt via een ESP32-chip. De Ulanzi TC001 maakt gebruik van een ESP32-WROOM-32D module. Kenmerken Pixel weergave. Gelijktijdige weergave van het aantal volgers: groei van het aantal fans is direct zichtbaar, geschikt voor YouTube, Bilibili en Weibo. Pomodoro Clock Design: beheer je eigen tijd op een meer wetenschappelijke wijze. Ontdek de onbegrensde mogelijkheden: er kunnen meerdere programma's via de besturingsserver worden geïnstalleerd om meerdere functies te creëren. Awtrix maakt het beter: de Awtrix simulator in de firmware van de TC001 simuleert een Awtrix matrix, en stelt u in staat om de klok te besturen met behulp van een standaard Awtrix host. Een hi-tech en indrukwekkend uiterlijk: eenvoudig de juiste sfeer te creëren, een LED-kleuren pixelscherm met een beter beeld. Een ingebouwde 4400 mAh accu met een accu gebruiksduur tot 5 uur. Specificaties Aantal LED's: 256 (8x32) Bedrijfsspanning: 3,7 V Verbruik: 3 W Accu capaciteit: 4400 mAh Interface: USB-C Afmetingen: 200,6 x 70,3 x 31,9 mm Gewicht: 283 g Inbegrepen Ulanzi TC001 Smart Pixel Clock USB-kabel Handleiding Downloads Firmware
€ 89,95
Leden € 80,96
4tronix Picon Zero v1.3 - Intelligent Robotics Controller for Raspberry Pi
The Picon Zero is an add-on for the Raspberry Pi. It has the same size as a Raspberry Pi Zero, making it ideal to function as a pHat. Of course, it can be used on any other Raspberry Pi via a 40-pin GPIO connector.As well as two full H-Bridge motor drivers, the Picon Zero has several Input/Output pins giving you multiple configuration options. That allows you to easily add outputs or analog inputs to your Raspberry Pi without any complicated software or kernel-specific drivers. At the same time, it opens up 5 GPIO pins from the Raspberry Pi, and it provides the interface for an HC-SR04 ultrasonic distance sensor.The Picon Zero comes with all components, including the headers and screw terminals, fully soldered. Soldering isn't required. You can use it right out of the box.Features pHat format PCB: 65 mm x 30 mm Two full H-Bridge motor drivers. Drive up to 1.5 A continuously per channel, at 3 V - 11 V. Each motor output has both a 2-pin male header and a 2-pin screw terminal. The motors can be powered from the Picon Zero's 5 V or an external power source (3 V - 11 V). The Picon Zero's 5 V can be selected to be from the Raspberry Pi's 5 V line, or a USB connector on the Picon Zero. That means that you can effectively have 2 USB battery banks: one to power the servos and motors on the Picon Zero and the other to power the Pi. 4 Inputs that can accept up to 5 V. These inputs can be configured as follows: Digital inputs Analog inputs DS18B20 DHT11 6 Outputs that can drive 5 V and be configured as: Digital Output PWM Output Servo NeoPixel WS2812 All Inputs and Outputs use GVS 3-pin male headers. 4-pin female header that connects directly to an HC-SR04 ultrasonic distance sensor. 8-pin female header for Ground, 3.3 V, 5 V, and 5 GPIO signals allowing you to add their additional features. Hardware ConfigurationPicon Zero has two jumpers for setting the hardware configuration. Ensure that you have placed them in the correct position. JP1 – Board 5 V Selector. This jumper selects where to get the 5 V power from for the Picon Zero Outputs. The options are: Jumper at the top between RPI and 5 V. The 5 V power for the board is taken from the Raspberry Pi pins on the GPIO connector. Because of the low power output devices and the 5 V motors, all devices can be powered with a single 5 V power input. Jumper at the bottom between USB and 5 V. The 5 V power is taken from the microUSB connector on the Picon Zero. Useful for higher power output devices, since you can provide extra power through the micro-USB connector on the board JP2 – Motor Power Selector. This jumper selects where the motors get the power. The two options here are the following: Jumper at the top between MotorPower and Vin. The motors are driven via the 2-pin screw terminal. The voltage can be between 3 V and 11 V. Useful for motors that require a voltage different from 5 V, or that require more current than is available on either of the USB input connectors Jumper at the bottom between 5 V and MotorPower. The motors are driven from the board's 5 V. Raspberry Pi ConfigurationThe Picon Zero is an I²C device. Make sure your Raspberry Pi is set up correctly to use I²C and SMBus: sudo apt-get install python-smbus python3-smbus python-dev python3-dev sudo nano /boot/config.txt Add the following lines at the end of the file dtparam=i2c1=on dtparam=i2c_arm=on Press Ctrl-X and use the default prompts to save sudo reboot Plugin the Picon Zero onto the Pi and run i2cdetect -y 1If everything goes well, you will see the Picon Zero showing up as address 22 as shown below:
€ 18,95€ 13,95
Leden identiek
FNIRSI FNIRSI S1 Smart Multimeter
De FNIRSI S1 draagbare digitale multimeter kan nauwkeurig AC/DC-spanning, weerstand, NCV, diode, continuïteit, capaciteit, temperatuur, frequentie en stroomvoerend draad meten. Het is een erg handig hulpmiddel voor het oplossen van elektrische problemen in de industrie en thuis. Hij is geschikt voor het meten van stopcontacten, zekeringen, accu’s (inclusief die van voertuigen), het testen en oplossen van problemen met elektronica in auto’s, oplaadsystemen, enz. Smart multimeter De multimeter kan automatisch AC/DC-spanning, weerstand en continuïteit detecteren, wat handig is voor zowel beginners als professionals. Specificaties AC-spanning 0 ~ 1000 V ±(0,8% +3) DC-spanning 0 ~ 1000 V ±(0,8% +3) Weerstand 0 ~ 100 M? ±(1,2% +3) Capaciteit 0 nF ~ 10 mF ±(4,5% +5) Frequentie 0 Hz ~ 10 Mhz ±(0,1% +3) Temperatuur -20 ~ 1000°C ±(2% +5) Diode Ja Automatisch UIT Ja Verlichting Ja Aan/uit-zoemer Ja Automatisch bereik Ja NCV geïnduceerde spanning Ja Live modus Ja Data hold Ja Analoog Ja Lage spanning indicatie Ja Max. bereik 9999 counts Geldige waardes 50 Hz ~ 1 kHz Materiaal ABS Weergave VA kleurenscherm Voeding via USB-C (1000 mA oplaadbare lithium accu) Afmetingen 143 x 75 x 19 mm Gewicht 135 g Inbegrepen FNIRSI S1 Multimeter Tip table pen Temperatuursonde USB-kabel Handleiding Downloads Handleiding
€ 34,95
Leden € 31,46
Dragino Dragino LPS8 Indoor LoRaWAN Gateway (EU868)
De Dragino LPS8 is een open source meerkanaals LoRaWAN gateway. Hiermee kan een LoRa-radionetwerk worden verbonden met een IP-netwerk via WiFi of Ethernet. Met het LoRa-radionetwerk kunnen gegevens over extreem grote afstanden met lage datasnelheden worden verzonden.De LPS8 maakt gebruik van Semtech Packet Forwarder en is volledig compatibel met het LoRaWAN protocol. Het omvat een SX1308 LoRa-concentrator die 10 programmeerbare parallelle demodulatiepaden biedt.LPS8 heeft voorgeconfigureerde standaard LoRaWAN-frequentiebanden voor gebruik in verschillende landen. De gebruiker kan de frequentiebanden ook aanpassen voor gebruik in zijn eigen LoRa-netwerk.Features Linux-gebaseerd OpenWrt systeem Beheer via intuïtieve Web GUI, SSH via LAN of WiFi Toegang op afstand met Reverse-SSH Emuleert 49x LoRa-demodulatoren LoRaWAN Gateway 10 programmeerbare parallelle demodulatiepaden Applicaties Logistiek en toeleveringsketenbeheer Slimme gebouwen en huisautomatisering Slimme steden Slimme landbouw Slimme fabriek Slimme meters Specificaties Stroomvoorziening via USB-C (5 V, 2 A) 1x USB-hostpoort 1x RJ45 (10/100 Mbit/s) 1x 2,4 GHz WiFi (802.11 b/g/n) LoRa Specs: 1x SX1308 Lora-concentrator 2x 1257 LoRa-transceiver Downloads Datasheet User Manual Source Code on GitHub Dragino LoRa Gateway Selection Guide Dragino LPS8 als Helium Data-Only Hotspot Dragino LoRaWAN Gateway Setup Dragino Gateways/Hotspots with Helium Tutorial Firmware
€ 199,95
Leden € 179,96
FNIRSI FNIRSI DMT-99 smart multimeter
De FNIRSI DMT-99 is een intelligente digitale multimeter met 10000 counts, die een hoog meetbereik en een hoge resolutie biedt. Hij kan nauwkeurig AC/DC spanning, AC/DC stroom en 10 A stroom meten. Daarnaast kan hij ook worden gebruikt voor het testen van geleiding, capaciteit, frequentie, duty cycle, weerstand, diode, temperatuur, NCV, live wire detectie, enz. Hij is geschikt voor gebruik bij een variëteit aan elektronische onderhoud, zoals bij machinebouw, laboratoria, auto's en huishoudelijke apparaten. Hij is uitgerust met een lithium accu van 1500 mAh en een 2,4-inch TFT-kleurenscherm met een resolutie van 240 x 320 pixels. Specificaties Functie Bereik Nauwkeurigheid DC spanning 9,999 V / 99,99 V / 999,9 V ±(0,5% + 3) AC spanning 9.999 V / 99,99 V / 750,0 V ±(1% + 3) DC stroom 9999 uA / 99,99 mA / 999,9 mA / 9,999 A ±(1,2% + 3) AC stroom 9999 uA / 99,99 mA / 999,9 mA / 9,999 A ±(1,5% + 3) Weerstand 9,999 M? / 999,9 K? / 99,99 K? / 9,999 K? / 999,9 ? ±(1,5% + 3) 99,99 M? ±(1,5% + 3) Capaciteit 999,9 ?F / 99,99 ?F / 9,999 ?F / 999,9 nF / 99,99 nF / 9,999 nF ±(2,0% + 3) 9,999 mF / 99,99 mF ±(5,0% + 3) Frequentie 9,999 MHz / 999,9 KHz / 9999 KHz / 9,999 KHz / 999,99 Hz / 99,99 Hz / 9,999 Hz ±(0,1% + 3) Temperatuur -55 ~ 1300 °C (-64 ~ 2372 °F) ±(2,5% + 3) Diode Ja Continuïteitstest Ja NVC Ja Live wire detectie Ja Max waarde display 10000 counts Accu capaciteit 1500 mAh Afmetingen 155 x 80 x 36 mm Gewicht 191 g Inbegrepen 1x FNIRSI DMT-99 multimeter 2x Testpennen 1x USB-C oplaadkabel 1x Handleiding
€ 44,95
Leden € 40,46
Elektor Digital Édition spéciale : rédaction invitée Espressif 2023 (PDF)
Le téléchargement intégral de ce numéro est disponible pour nos membres GOLD et GREEN sur le site Elektor Magazine ! Pas encore membre ? Cliquez ici. accélérer l'innovation IdO cadre photo couleur à encre électronique Wi-Fi tutoriel ESP-Launchpadflashage des micrologiciels en quelques minutes ESP32 et ChatGPTvers un système d'autoprogrammation... Talkie-walkie avec ESP-NOWPas tout à fait Wi-Fi, pas tout à fait Bluetooth non plus... de l'idée au circuit avec l'ESP32-S3construire un prototype avec les puces Espressif innovation des puces AIoTentretien avec Teo Swee-Ann, PDG d'Espressif simuler l'ESP32 avec Wokwile jumeau numérique de votre projet essai de l'ESP32-S3-BOX-3une plateforme de développement AIoT complète bien s?équiper pour mieux travaillerconseils et astuces des ingénieurs d?Espressif l'histoire de l'ESP RainMakerComment nous avons construit « votre » nuage IdO assemblage du kit du Cloc 2.0 d?Elektorun produit Elektor déballé par Espressif le lancement de l'ESP32-P4la nouvelle ère des microcontrôleurs Rust et les systèmes embarquésdeux outils puissants pour le développement qui sont les développeurs de solutions embarquées Rust ?comment Espressif développe le langage Rust embarqué pour l'ESP32 Série de SoC Espressif une API avec les Solutions d'Espressifavec les capacités et les fonctionnalités du protocole ISOBUS la carte VGA ESP32-S3le voyage passionnant de Bitluni dans la conception de produits empreinte acoustique sur ESP32identification de chansons avec le projet open source Olaf arbre de Noël circulaire 2023célébration high-tech des fêtes de fin d'année une vie plus confortable et plus facileun projet amateur basé sur le module ESP8266 Espressif comment construire des applications IoT Sans Expertise Logicielle Avec la plateforme IoTavec la plateforme IoT Blynk et le matériel Espressif concevoir une Interface Graphique sur ESP32 développement IoT rapide et facile avec M5Stack prototypage d'un compteur d'énergie basé sur l'ESP32 un distributeur à valeur ajoutée de solutions IdO et plus encore En détail : entretien avec Arduino sur le Nano ESP32Alessandro Ranellucci et Martino Facchin abordent la collaboration avec Espressif innovation des puces IdOles idées d'Espressif simplifier le développement des microcontrôleurs avec ESP-IDF Privilege Separation un serveur de reconnaissance de la parole open-source......et l'ESP BOX l??il qui réfléchitreconnaissance faciale et plus encore, utilisant l?ESP32-S3-EYE commutateur alimenté par pile bouton, basé sur un ESP32-C2évaluation de la conception et des performances la maison intelligente évolue avec Matterlibérer le potentiel de l'IdO pour les maisons intelligentes l'essor de la maison intelligente connectée
€ 10,95
Leden € 9,86
FNIRSI FNIRSI HS-01 Slimme Soldeerbout (incl. 6 soldeertips)
Het perfecte gereedschap voor de snelle reparatiesDe HS-01 is een krachtige, verstelbare slimme soldeerbout met een ingebouwd 0,87' OLED-display, die snel temperaturen tussen 80-420°C kan bereiken. Het display toont alle belangrijke informatie, waaronder de hoogte van de temperatuur, de ingestelde temperatuur, de voedingsspanning en het gebruikte vermogen. U kunt de werkspanning direct in het menu naar wens instellen tussen 9-20 V. De geïntegreerde sleeptimer schakelt de bout automatisch na 30 minuten uit.Kenmerken 96 W ingang (DC) 65 W PD vermogen OLED-display Constante temperatuur & snelle opwarming CNC-metaal integraal gegoten Slimme beveiliging tegen verbranding Mini zakformaat Ergonomisch ontwerp Aluminium materiaal Links/rechts schakelaar Efficiënte warmte afgifte inductieve slaap mode Kleur: zwart Specificaties Verbruik 65 W Scherm 0,87 inch OLED Werkspanning 9 - 20 V DC Voeding USB-C Temperatuurbereik 80 – 420 °C (180 – 780 °F) Snellaad protocol PD trigger Afmetingen 184 x 20 x 20 mm (7,24 x 0,79 x 0,79 inch) Gewicht 56 g Vermogensselectie Werkspanning 20 V 15 V 12 V 9 V Bedrijfsstroom ? 3,25 A ? 2,5 A ? 2 A ? 1,5 A Vermogen 65 W 37,5 W 24 W 13,5 W Tin smelttijd 8 s 12 s 17 s 30 s Inbegrepen 1x FNRISI HS-01 slimme soldeerbout 6x Soldeerbout tips (HS01-BC2, HS01-KR, HS01-K65, HS01-B2, HS01-ILS, HS01-BC3) 1x DC naar USB-C voedingskabel 1x Standaard voor mini soldeerbout 1x Handleiding Vereist Voedingsadapter USB-C kabel DownloadsGebruikershandleiding
€ 74,95
Leden € 67,46
Elektor Digital Elektor Mei/Juni 2020 (PDF)
Open-netwerk weerstation mk2deel 1: inleiding en hardware-elementen AI voor beginners (1)objectherkenning met het Maixduino-board Universele triac-stuurmodule met ATmegaschakelen en dimmen van verschillende belastingen Hoe... iets van GitHub downloadenGitHub Voor Dummies My IoT-Button: de knop voor het netdeel 2: prototyping met board en cloud TMS0280 spraaksynthesizervreemde onderdelen Interactiefcorrecties & updates | vragen & antwoorden BASIC voor ESP32/ESP8266 (2)zandloper met ESP8266 en Annex WiFi RDS Developer’s Zonetips & trucs, vakkunstigheden en andere nuttige informatie BalBot: een zelfbalancerende robotmoderne versnellingssensoren vergemakkelijken de bouw Alle begin......hoeft niet zo moeilijk te zijn Wie het kleine niet eertuit de ideeënbus van Elektor Verzendbox met manipulatie-indicatiegegevens veilig met de post verzenden Nieuwe Nauwkeurige Nixie-klok: verbeteringentechnisch nieuwsbulletin voor nieuwe en bestaande enthousiaste gebruikers Multitasking met de ESP32 (3)software-timers Met de vos in het IoT (4)inrichten van het dashboard Start-up update: het Elektor Investment Program Review: Elektronische USB-belasting Joy-IT HD35test de belastbaarheid van USB-poorten CAN-bus + Arduino houden zonnepanelen in de gatenlokaliseer panelen in grote arrays die onderhoud nodig hebben Analoge elektronica ontwerpencase-study #1 – deel 3: optimalisatie van de responsie van de voorversterker en compromissen Sound Blinkdraagbare zelfbouwspeaker met LED-lichtshow USB-stroombewakingintelligente bescherming voor USB-poorten Oost West Lab Besteen blik in het allerheiligste, waar onbevoegden geen toegang hebben... Review: Labvoeding PeakTech 6080 Aveel voeding voor weinig geld Een grote uitdagingveilige producten in het IoT-tijdperk Elektor 1,2-GHz-universeelteller (1992/93)voorbij de magische 1GHz-grens Hexadoku
€ 9,95
Leden € 8,96
Sequent Microsystems Smart Fan HAT for Raspberry Pi
Raspberry Pi 4 was welcomed by the Pi enthusiasts for the increased processing power. However, this came at a price. The RPi 4 can draw up to 3 Amps, which means it has to dissipate 15 W of power. Raspberry Pi cooling is a must. From the simplest passive heat sink, through elaborate fan blowers and even to an exotic water-cooled idea, many options are available.The Smart Fan has the form factor of the Raspberry Pi HAT. Its own tinny 32-bit processor receives commands from Raspberry Pi through the I²C interface. A step-up power supply converts the 5 V provided by Raspberry Pi to 12 V, ensuring precise speed control. Using pulse width modulation, it powers the fan just enough to maintain a constant temperature of the Raspberry Pi processor.The Smart Fan preserves all the GPIO pins, allowing any number of cards to be stacked on top of Raspberry Pi. If another add-on card has to dissipate power, a secondary Smart Fan can be added to the stack.DIN-Rail MountingTogether with multiple add-on cards, the Smart Fan can be installed on the DIN-Rail, for sturdy industrial applications.Stack Level JumperTwo Smart Fans can be installed on top of each Raspberry Pi. The assumption is that you have one more card in the stack which requires cooling. The bottom side of the Smart Fan has a jumper which needs to be installed on the second fan, in order for the Raspberry Pi to differentiate the two I²C addresses.Features 40 x 40 x 10 mm fan with 6 CFM airflow Step-up 12 V power supply for precise fan speed control PWM Controller modulates the fan to keep constant Pi temperature Draws less than 100 mA of power Stackable to itself, 2 fans can be added to Raspberry Pi Fully stackable allows adding other cards to Raspberry Pi Uses only I²C interface, leaves full use of all GPIO pins Super quiet and efficient Included Smart Han HAT 40 x 40 x 10 mm Fan with mounting Screws Mounting Hardware Downloads User's Guide Open Source Hardware Schematic 2D CAD Drawing Command line Python Libraries Node-Red Nodes
€ 24,95
Leden € 22,46
Home Assistant Home Assistant Green
Zet de eerste stap om uw smart home te upgraden met Home Assistant Green, de makkelijkste manier om Home Assistant te gebruiken. Dankzij de krachtige hardware kunt u met Home Assistant alles in uw huis bedienen en automatiseren vanuit één app. Sluit simpelweg stroom- en netwerkkabels aan en u kunt aan de slag. Download onze mobiele apps, of gebruik onze webapp, om u naadloos door het installatieproces te leiden. Dat is alles! Home Assistant begint automatisch met het detecteren van je smart home apparaten. Alles in één app Meer dan 1.000 ingebouwde integraties ondersteunen honderdduizenden slimme apparaten en online services, en er worden er door onze community regelmatig meer toegevoegd. Switch in uw eigen tempo over van andere smart home ecosystemen Home Assistant werkt met je bestaande configuratie met Apple HomeKit, Google Home, Samsung SmartThings en Amazon Alexa, waardoor een naadloze en geleidelijke migratie voor iedereen in uw huis mogelijk is. Breid de compatibiliteit uit naarmate uw huis groter wordt U kunt Home Assistant SkyConnect toevoegen om Zigbee en Thread apparaten aan te kunnen sluiten, Home Assistant Cloud in te stellen voor spraakassistenten, en USB-accessoires van derden te integreren om andere slimme standaarden te ondersteunen, zoals Z-Wave of Bluetooth. Home Assistant is gebouwd door een van de grootste community's van open source ontwikkelaars. Elke maand worden er nieuwe functies en verbeteringen toegevoegd, zodat je smart home je nooit in de steek laat. Home Assistant bewaart uw data lokaal, wat betekent dat u beschermd bent tegen invasieve privacy activiteiten, en zorgt ervoor dat u toegang hebt tot uw smart home, zelfs als het internet niet beschikbaar is. Specificaties SoC Rockchip RK3566 SoC met quad-core Arm Cortex-A55 CPU CPU frequentie 1,8 GHz Opslag 32 GB eMMC flash drive RAM 4 GB LPDDR4X Interfaces Status LED's Wit (voedingsindicatie)Groen (activiteitsindicatie)Geel (systeemstatus) Voeding DC barrel connector, 5,5 x 2,1 mm12 V DC, 1 A Batterij CR2032 (niet inbegrepen) Energieverbruik Inactief: ~1,7 W bij 12 VBelast: ~3 W bij 12 V USB 2x USB 2.0 Type-A Host poorten, 5 V tot 2 A (gecombineerd) Display HDMI-poort, alleen voor diagnostische doeleinden Externe opslag MicroSD-slot, alleen voor hersteldoeleinden Netwerk Gigabit Ethernet Afmetingen 112 x 112 x 32 mm Gewicht 340 g Inbegrepen Home Assistant Green smart home hub Gigabit ethernet kabel 12 V/1 A universele voeding (wordt geleverd met stekkeradapters voor EU, VS en VK) Quick Start guide Garantie- en veiligheidsinformatie Downloads Datasheet Documentatie GitHub
€ 129,95
Leden € 116,96
Raspberry Pi Foundation Raspberry Pi Build HAT
Build robust, intelligent machines that combine Raspberry Pi computing power with LEGO components.The Raspberry Pi Build HAT provides four connectors for LEGO Technic motors and sensors from the SPIKE Portfolio. The available sensors include a distance sensor, a colour sensor, and a versatile force sensor. The angular motors come in a range of sizes and include integrated encoders that can be queried to find their position.The Build HAT fits all Raspberry Pi computers with a 40-pin GPIO header, including?–?with the addition of a ribbon cable or other extension device?—?Raspberry Pi 400. Connected LEGO Technic devices can easily be controlled in Python, alongside standard Raspberry Pi accessories such as a camera module.Features Controls up to 4 motors and sensors Powers the Raspberry Pi (when used with a suitable external PSU) Easy to use from Python on the Raspberry Pi
€ 34,95€ 27,95
Leden identiek
-
, door Jean-François Simon Fnirsi HS-01 slimme soldeerbout (Review)
De HS-01, geproduceerd door Fnirsi, is een soldeerbout ontworpen voor gebruik met vele verschillende voedingsbronnen.