Zoekresultaten voor "blue t"
Kuongshun 2x16 Character LCD Module (blue/white)
2x16 Character LCD Module (blue/white) Pin No. Pin Name Descriptions 1 VSS Ground 2 VDD Supply voltage for logic 3 V0 Input voltage for LCD 4 RS Data / Instruction Regster Select (H : Data signal, L : Instruction signal) 5 R/W Read / Write (H : Read mode, L : Write mode) 6 E Enable signal 7 DB0 Data bit 0 8 DB1 Data bit 1 9 DB2 Data bit 2 10 DB3 Data bit 3 11 DB4 Data bit 4 12 DB5 Data bit 5 13 DB6 Data bit 6 14 DB7 Data bit 7 15 LED_A Backlight Anode 16 LED_K Backlight Cathode
€ 5,95
Leden € 5,36
Velleman Velleman Antistatic Adjustable Elastic Wrist Strap (Blue)
Specifications Material: Conductive fastener tape: nylon Interior surface: conductive carbon Grounding cord: PU coil cord with resistor of 1 Mohm Band size: 2 x 23 cm Band resistivity: < 50 Ohm Color: blue
€ 3,95
Leden € 3,56
Velleman Velleman 3D LED Cube 5x5x5 (Blue LED)
Features LEDs: 5 x 5 x 5 = 125 LEDs User programmable via USB (creation of animation/scenes) Large amount of user programmable frames Frames are separately dimmable 4 transition speeds Available frames: 3200 5 levels LED dimming available No coding skills required Software similar to (3 x 3 x 3) Specifications Regulated power supply: 9 VDC (not incl.) Power consumption: 300 mA max. Dimensions: 110 x 110 x 150 mm / 4.33 x 4.33 x 5.9?
€ 59,95
Leden € 53,96
Kuongshun 0.96" OLED Display (Blue, I²C, 4-Pin)
0,96" (24 mm) monochroom grafisch OLED-display met een resolutie van 128 x 32 pixels, gemonteerd op een printplaat van 28 x 28 mm. Het effectieve weergaveoppervlak is 11 x 23 mm. Het heeft een 4-pins connector voor gebruik met een I²C-bus (met SCL & SDA signalen). Het display werkt met 5 V en 3,3 V toepassingen. Specificaties Grootte: 0,96 inch / 24 mm Resolutie: 128 x 32 pixels Afmetingen printplaat: 28 x 28 mm Effectief weergaveoppervlak: 11 x 23 mm Visuele hoek: 160 ° Ingangsspanning: 3,3 V ~ 6 V Brede spanningsondersteuning: 3,3 V, 5 V Kijkhoek: 160 ° Stuur-IC: SSD1306 Bedrijfstemperatuur: -30 °C tot 80 °C I²C Signalen: SCL, SDA I²C-adres: 0x78 (of 0x3c, standaard) of 0x7a (of 0x3d). Opmerking: I²C-adressen kunnen (helaas) op twee manieren worden gespecificeerd: met of zonder R/W-bit. Daarom is 0x78 (0x7a) inclusief het R/W-bit gelijk aan 0x3c (0x3d) zonder R/W-bit. OLED Voordelen Kleiner volume Ultra-laag stroomverbruik Hoog contrast Weergavepunt zelflichtend Brede spanningsondersteuning Waarschuwing: Het glas van het display is breekbaar, wees voorzichtig bij het gebruiken ervan. Als het glas breekt, zal het scherm niet goed werken.
€ 9,95
Leden € 8,96
SB Components SB Components Raspberry Pi Pico LED Cube (4x4x4 Blue LEDs)
De Pico Cube is een 4x4x4 led kubus HAT voor Raspberry Pi Pico met 5 VDC bedrijfsspanning. De Pico Cube, een monochromatisch Blauw met 64 leds, leert u op een leuke manier programmeren. Hij is ontworpen om lichtgevende bewerkingen te tonen met een laag energieverbruik, heeft een robuust ontwerp en is eenvoudig te installeren, waardoor mensen / kinderen / gebruikers de effecten op leds met een verschillend kleurenpatroon leren kennen door software en hardware, zoals de Raspberry Pi Pico, te combineren. Kenmerken Standaard 40-pins Raspberry Pi Pico header GPIO-gebaseerde communicatie 64 high-intensity monochromatische leds Toegang tot individuele leds Toegang tot elke laag Specificaties Bedrijfsspanning: 5 V Kleur: blauw Communicatie: GPIO Leds: 64 Inbegrepen 1x Pico Cube basis PCB 4x PCB lagen 8x PCB pilaren 2x berg strips (1 x 20), male 2x berg strips (1 x 20), female 70 leds Opmerking: Raspberry Pi Pico is niet inbegrepen. Downloads GitHub Wiki
€ 29,95
Leden € 26,96
Pimoroni Pimoroni Maker Essentials - 50 colorful LEDs & Resistors
Add colors to your projects with this collection of red, green, yellow, blue and white LEDs. They come with various current limiting resistors in order to protect the parts and control the brightness.Included 10 mm LEDs 1x red 1x green 1x yellow 1x blue 1x white 5 mm LEDs 5x red 5x green 5x yellow 5x blue 5x white 3 mm LEDs 5x red 5x green 5x yellow 5x blue 5x white 25x 330 ? resistors 10x 1 k? resistors 10x 10 k? resistors 10x 100 k? resistors 10x 1 M? resistors
€ 14,95
Leden € 13,46
SparkFun SparkFun Thing Plus Matter (MGM240P)
The SparkFun Thing Plus Matter is the first easily accessible board of its kind that combines Matter and SparkFun’s Qwiic ecosystem for agile development and prototyping of Matter-based IoT devices. The MGM240P wireless module from Silicon Labs provides secure connectivity for both 802.15.4 with Mesh communication (Thread) and Bluetooth Low Energy 5.3 protocols. The module comes ready for integration into Silicon Labs' Matter IoT protocol for home automation.What is Matter? Simply put, Matter allows for consistent operation between smart home devices and IoT platforms without an Internet connection, even from different providers. In doing so, Matter is able to communicate between major IoT ecosystems in order to create a single wireless protocol that is easy, reliable, and secure to use.The Thing Plus Matter (MGM240P) includes Qwiic and LiPo battery connectors, and multiple GPIO pins capable of complete multiplexing through software. The board also features the MCP73831 single-cell LiPo charger as well as the MAX17048 fuel gauge to charge and monitor a connected battery. Lastly, a µSD card slot for any external memory needs is integrated.The MGM240P wireless module is built around the EFR32MG24 Wireless SoC with a 32-bit ARM Cortext-M33 core processor running at 39 MHz with 1536 kb Flash memory and 256 kb RAM. The MGM240P works with common 802.15.4 wireless protocols (Matter, ZigBee, and OpenThread) as well as Bluetooth Low Energy 5.3. The MGM240P supports Silicon Labs' Secure Vault for Thread applications.Specifications MGM240P Wireless Module Built around the EFR32MG24 Wireless SoC 32-bit ARM-M33 Core Processor (@ 39 MHz) 1536 kB Flash Memory 256 kB RAM Supports Multiple 802.15.4 Wireless Protocols (ZigBee and OpenThread) Bluetooth Low Energy 5.3 Matter-ready Secure Vault Support Built-in Antenna Thing Plus Form-Factor (Feather-compatible): Dimensions: 5.8 x 2.3 cm (2.30 x 0.9') 2 Mounting Holes:4-40 screw compatible 21 GPIO PTH Breakouts All pins have complete multiplexing capability through software SPI, I²C and UART interfaces mapped by default to labeled pins 13 GPIO (6 labeled as Analog, 7 labeled for GPIO)All function as either GPIO or Analog Built-in-Digital to Analog Converter (DAC) USB-C Connector 2-Pin JST LiPo Battery Connector for a LiPo Battery (not included) 4-Pin JST Qwiic Connector MC73831 Single-Cell LiPo ChargerConfigurable charge rate (500 mA Default, 100 mA Alternate) MAX17048 Single-Cell LiPo Fuel Gauge µSD Card Slot Low Power Consumption (15 µA when MGM240P is in Low Power Mode) LEDs: PWR – Red Power LED CHG – Yellow battery charging status LED STAT – Blue status LED Reset Button: Physical push-button Reset signal can be tied to A0 to enable use as a peripheral device Downloads Schematic Eagle Files Board Dimensions Hookup Guide Datasheet (MGM240P) Fritzing Part Thing+ Comparison Guide Qwiic Info Page GitHub Hardware Repo
€ 34,95
Leden € 31,46
Kuongshun Basic Kit for Raspberry Pi Pico (Pico included)
Contents Raspberry Pi Pico RP2040 Development Board 30 cm Micro:bit flat USB cable for Smart Car 10-Pin Male to Female Dupont Line Three-leaf Fan Blue Motor Bracket with Screw 3 V DC motor with wire ULN2003 Driver Board Stepper Motor Green 28 mm Leg LED 5 mm Red (1pcs) 28 mm Leg LED 5 mm Green (1pcs) 28 mm Leg LED 5 mm Yellow (1pcs) 28 mm Leg LED 5 mm Blue (1pcs) Resistor 220R 1/4W 1% (1pcs) 400 Points Soldless Breadboard Infrared Obstacle Avoidance Tracking Sensor Module Active Alarm Buzzer Driver Module Low Current Blue 7 Color Flashing LED Module Tachile Switch Module
€ 34,95
Leden € 31,46
SparkFun SparkFun Thing Plus (RP2040)
De RP2040 bevat twee ARM Cortex-M0+ processoren (tot 133MHz) en beschikt over: 264 kB ingebed SRAM in zes banken 6 speciale IOs voor SPI Flash (met ondersteuning voor XIP) 30 multifunctionele GPIOs: Specifieke hardware voor veelgebruikte periferie Programmeerbare IO voor uitgebreide periferie-ondersteuning Vier 12-bit ADC-kanalen met interne temperatuursensor (tot 0,5 MSa/s) USB 1.1 Host/Device-functionaliteit De RP2040 wordt ondersteund met C/C++ en MicroPython cross-platform ontwikkelomgevingen, inclusief eenvoudige toegang tot runtime debugging. Het heeft een UF2 boot ROM en floating-point routines ingebouwd in de chip. Terwijl de chip een groot intern RAM geheugen heeft, bevat de kaart een extra 16MB extern QSPI flash geheugen om programmacode op te slaan. Eigenschappen Raspberry Pi Foundation's RP2040 microcontroller 16MB QSPI Flash Geheugen JTAG PTH pinnen Thing Plus (of Feather) Form-Factor: 18 x Multifunctionele GPIO-pennen Vier 12-bit ADC kanalen met een interne temperatuursensor (500kSa/s) Tot acht 2-kanaals PWM Tot twee UART's Tot twee I2C-bussen Tot twee SPI-bussen USB-C-aansluiting: USB 1.1 Host/Device-functionaliteit 2-pins JST-aansluiting voor een LiPo-batterij (niet meegeleverd): 500mA laadcircuit Qwiic Aansluiting Druktoetsen: Boot Reset LEDs: PWR - Rode 3,3V voedingsindicatie CHG - Gele batterij laadindicatie 25 - Blauwe status/test-LED (GPIO 25) WS2812 - Adresseerbare RGB-LED (GPIO 08) Vier montagegaten: 4-40 schroefcompatibel Afmetingen: 2,3' x 0,9' RP2040 Kenmerken Dubbele Cortex M0+ processoren, tot 133 MHz 264 kB ingebed SRAM in 6 banken 6 speciale IOs voor QSPI flash, met ondersteuning voor execute in place (XIP) 30 programmeerbare IOs voor uitgebreide periferie-ondersteuning SWD-interface Timer met 4 alarmen Real-time clock (RTC) USB 1.1 Host/Device-functionaliteit Ondersteunde programmeertalen MicroPython C/C++
€ 19,95
Leden € 17,96
PeakTech PeakTech 3125 Power Strip with 2 x 230 V Safety Sockets and 2 x USB Charger with 2.5 A
This handy power strip provides two child-proof, shockproof sockets and two USB charging ports with a high maximum charging current. On the front side there is a holder for smartphones and tablet PCs, which, thanks to its slightly angled shape, enables outstanding usability of the device. The non-slip rubber knobs on the underside prevent slipping on the work table, with a blue LED integrated as a power indicator. 2 x 16 A safety sockets with child safety lock 2 x USB charging ports with high charging current of 2.5 A Angled bracket for tablet PCs and smartphones Non-slip rubber knobs at the bottom
€ 17,95
Leden € 16,16
Short Circuits: The 4-Pack (Arduino-compatible Electronics Platform)
Get started with microcontroller based electronicsThis Arduino-compatible bundle contains the Motherboard, Digitiser, Sensor Array and RGB Matrix. With these 4 boards you have everything you need to build a clock, score counter, timer, task reminder, thermometer, humidity display, sound meter, light meter, clap trigger, colored bar graph display, animated alarm, and much more! The Motherboard has a built in real time clock module that keeps time even when unplugged. The Digitiser can display 4 digits or characters and includes 2 buttons and a potentiometer to let you control what’s being displayed, or the brightness of the display. The Sensor Array can read temperature, relative humidity, sound and light, with an SD card slot for data recording. The RGB Matrix has 16 RGB LEDs that are controlled through shift registers, so only use 3 or 4 pins of the Motherboard. MotherboardThe Motherboard is an Arduino-compatible microcontroller breakout board designed around the ATmega328P. The board comes in a solder-it-yourself kit with all the components you need to get started with microcontroller based electronics. All other boards connect to this. Based on the ATmega328P Arduino compatible On-Board RTC (Real Time Clock) FTDI Header for easy programming Bluetooth Header Terminal Block Connections DigitiserThe Digitiser is a versatile display and input board. It let’s you visualise your data. Show your sensor information, clock digits, or even keep score for your favourite card game. The Digitiser also includes some buttons and a knob to let you take control. 4x 7-Segment Displays Uses 595 Shift Registers 2 Switches and a Potentiometer 4 colored 'Mode' LEDs Chainable with other 595 Boards Terminal Block Connections Sensor ArrayAs the name suggests, the Sensor Array is an array of sensors. Measure temperature and relative humidity via the DHT11, light via the light dependant resistor, and sound via the microphone and amplifier circuit. Then you can log the data using the on-board SD card slot. DHT11 Temp & Humidity Sensor Microphone and Amplifier Circuit Light Dependent Resistor MicroSD Slot for Saving Data Logic Level Converter Circuit Terminal Block Connections RGB MatrixAdd color to your project by controlling 16 red, 16 green and 16 blue LEDs with just 3 pins of your microcontroller. The RGB Matrix uses shift registers, a matrix and switching transistors, so there’s plenty to learn and explore. 4x4 (16) RGB LEDs Uses 595 Shift Registers Chainable with other 595 Boards Transistor Switches Terminal Block Connections Downloads (Manuals) Motherboard Digitiser Sensor Array RGB Matrix
€ 99,95
Leden € 89,96
-
, door Jean-François Simon LCR-meter: De UNI-T UT603 (Review)
Op zoek naar een draagbare LCR-meter? Bekijk de functies en toepassingen van de UNI-T UT603 LCR-meter in onze gedetailleerde review!