Zoekresultaten voor "Espressif ESP32-"
Espressif ESP32-S3-EYE
ESP32-S3-EYE is een klein AI ontwikkelboard. Hij is gebaseerd op de ESP32-S3 SoC en ESP-WHO, het AI development framework van Espressif. Het ESP32-S3-EYE board bestaat uit twee gedeelten: het moederboard (de ESP32-S3-EYE-MB) is voorzien van de ESP32-S3-WROOM-1 module, een 2-megapixel camera, een SD-kaart slot, een digitale microfoon, een USB poort en functieknoppen; en het subboard (de ESP32-S3-EYE-SUB) bevat een LCD-scherm. Het moederboard en het subboard zijn verbonden via pinheaders. De ESP32-S3-EYE biedt veel opslagruimte, met een 8 MB Octal PSRAM en een 8 MB flash. Hij ondersteunt ook beeldoverdracht via Wi-Fi en foutopsporing via een micro-USB poort. Specificaties Camera De camera OV2640 met 2 miljoen pixels heeft een kijkhoek van 66,5° en een maximale resolutie van 1600x1200. U kunt de resolutie wijzigen tijdens het ontwikkelen van de toepassingen. Module Aan/Uit LED De LED (groen) gaat branden wanneer de USB voeding op het board is aangesloten. Als deze niet brandt geeft dit aan dat de USB-voeding niet aangesloten is, of dat de LDO van 5 V naar 3,3 V kapot is. Met software kan GPIO3 worden geconfigureerd om verschillende LED-statussen in te stellen (aan/uit, knipperend) voor verschillende statussen van het bord. Opmerking: GPIO3 moet worden ingesteld in de open-drain modus. Een pull-up van GPIO3 doet de LED branden. Pin headers Verbinden de female headers op het subboard. 5 V naar 3,3 V LDO Vermogensregelaar die een 5 V voeding omzet naar een 3,3 V uitgang voor de module. Digitale microfoon De digitale I²S MEMS microfoon heeft een SNR van 61 dB en een gevoeligheid van -26 dBFS en werkt op 3,3 V. FPC connector Verbindt het moederboard en het subboard. Functieknop Er zitten zes functieknoppen op het board. Gebruikers kunnen alle functies naar wens configureren, behalve de RST knop. De ESP32-S3-WROOM-1 De ESP32-S3-WROOM-1 module bevat de ESP32-S3R8 chipvariant die Wi-Fi en Bluetooth 5 (LE) connectiviteit biedt, evenals speciale vectorinstructies voor het versnellen van neural netwerkcomputing en signaalverwerking. Naast dat de SoC een geïntegreerde 8 MB Octal SPI PSRAM bevat, wordt de module ook geleverd met 8 MB flash, waardoor snelle gegevenstoegang mogelijk is. De ESP32-S3-WROOM-1U module wordt ook ondersteund. MicroSD card slot Wordt gebruikt voor het plaatsen van een MicroSD-kaart om de geheugencapaciteit uit te breiden. 3,3 V naar 1,5 V LDO Vermogensregelaar die een voeding van 3,3 V omzet naar een uitgang van 1,5 V voor de camera. 3,3 V tot 2,8 V LDO Vermogensregelaar die een voeding van 3,3 V omzet naar een uitgang van 2,8 V voor de camera. USB poort Een micro-USB poort die wordt gebruikt voor 5 V voeding naar het board en voor communicatie met de chip via GPIO19 en GPIO20. Batterij soldeerpunten Worden gebruikt voor het solderen van een batterij-aansluiting om een externe Li-ion accu aan te sluiten, die kan dienen als alternatieve voeding voor het board. Als u een externe accu gebruikt, zorg er dan voor dat deze een ingebouwd beveiligingscircuit en zekering heeft. De aanbevolen specificaties van de accu: capaciteit > 1000 mAh, uitgangsspanning 3,7 V, ingangsspanning 4,2 V – 5 V. Acculader chip 1 A lineaire Li-ion acculader (ME4054BM5G-N) in ThinSOT uitvoering. De stroombron voor het opladen is de USB poort. Accu rode LED Wanneer de USB voeding op het board is aangesloten en er geen accu is aangesloten dan knippert de rode LED. Als er een accu is aangesloten en wordt opgeladen, gaat de rode LED branden. Wanneer de accu volledig is opgeladen dan wordt de LED uitgeschakeld. Accelerometer Drie-assige versnellingsmeter (QMA7981) voor schermrotatie, enz.
€ 59,95
Leden € 53,96
Espressif ESP32-PICO-Kit V4
De ESP32-PICO-KIT past in een mini breadboard. Het is volledig functioneel met een minimaal aantal discrete componenten, terwijl alle ESP32 pinnen beschikbaar zijn.Kenmerken Volledige up-to-date documentatie is beschikbaar. Alle beschreven instructies en commando’s werken zoals aangeven. Er is ook veel aanvullende informatie en hardware documentatie beschikbaar. Toepassingen voor de ESP32-PICO-KIT kunnen worden ontwikkeld op Windows, Linux of Mac. Twe cores en draadloosNet als de ESP8266 heeft de ESP32 WiFi, maar voegt daar Bluetooth aan toe. Hij heeft ook twee 32-bits cores aan boord, waardoor hij extreem krachtig is, en alle poorten en interfaces biedt die de ESP8266 mist. Je zou simpelweg kunnen stellen dat de ESP8266 een WiFi-controller is die wat I/O biedt, terwijl de ESP32 een volwaardige controller is die ook WiFi heeft.ESP32 randapparatuurDe ESP32 bevat een ADC &DAC, touch sensor circuits, een SD/SDIO/MMC host controller, een SDIO/SPI slave controller, een EMAC, PWM om LED's en motoren aan te sturen, UART, SPI, I²C, I²S, infrarood afstandsbediening en, natuurlijk, GPIO.ESP32-PICO-KIT Development board V4De ESP32-PICO-D4 is een System-on-Chip (SoC) die een ESP32-chip integreert in een 4 MB SPI-flashgeheugen van 7 x 7 mm.De ESP32-PICO-KIT is een breakout board voor deze SoC met een on-board USB-naar-serieel converter voor eenvoudig programmeren en debuggen.Behalve het board heb je ook een programming toolchain nodig. Volledige, up-to-date documentatie van Espressif is beschikbaar op de Read the Docs website.Alle beschreven instructies en commando’s werken zoals aangeven. Er is ook veel aanvullende informatie en hardware documentatie beschikbaar.Toepassingen voor de ESP32-PICO-KIT kunnen worden ontwikkeld op Windows, Linux of Mac.
€ 19,95
Leden € 17,96
Espressif ESP32-DevKitC-32E
De ESP32-DevKitC is een entry-level ontwikkelbord met een klein formaat die deel uitmaakt van de ESP32 serie. Dit board heeft een veel opties voor randapparatuur. De ingebouwde ESP32-pinout is geoptimaliseerd voor probleemloos prototypen! Wifi & Bluetooth connectiviteit Dit compacte ontwikkelbord wordt aangestuurd door een ESP32-module. Deze integreert wifi en Bluetooth functies en biedt veel opties qua randapparatuur om snel te kunnen prototypen! Snel prototypen De ESP32-DevKitC biedt optimale RF-prestaties. U kunt direct aan de slag met het ontwerpen en ontwikkelen van toepassingen zonder u zorgen te hoeven maken over de RF-prestaties en het antenne-ontwerp. ESP32-DevKitC voldoet al aan uw basis systeemvereisten. Sluit gewoon de USB-kabel aan en u bent klaar om aan de slag te gaan! Flexibel en rijk aan functies De ESP32-DevKitC bevat het volledige arsenaal aan ondersteuning voor de ESP32-WROOM serie, de ESP32-WROVER serie en de ESP32-SOLO serie modules, inclusief een USB-UART-brug, reset- en opstartmodus knoppen, een LDO-regelaar en een micro-USB connector. Elke belangrijke GPIO is toegankelijk gemaakt voor de ontwikkelaar. Breadboard-vriendelijk De ESP32-DevKitC pinout is geoptimaliseerd om prototypen op een breadboard mogelijk te maken. De ingebouwde LDO-uitgang is van buiten af toegankelijk om extra externe elektronica van stroom te voorzien. De uitgangen voor de randapparatuur zijn netjes gegroepeerd voor probleemloos prototypen. Kenmerken Board ESP32-DevKitC-32E Gerelateerde module ESP32-WROOM-32E Flash geheugen 4 MB Antenne PCB Downloads Datasheet
€ 14,95
Leden € 13,46
Espressif ESP32-S2-WROOM
At the core of this module is ESP32-S2, an Xtensa® 32-bit LX7 CPU that operates at up to 240 MHz. The chip has a low-power co-processor that can be used instead of the CPU to save power while performing tasks that do not require much computing power, such as monitoring of peripherals. ESP32-S2 integrates a rich set of peripherals, ranging from SPI, I²S, UART, I²C, LED PWM, TWAITM, LCD, Camera interface, ADC, DAC, touch sensor, temperature sensor, as well as up to 43 GPIOs. It also includes a full-speed USB On-The-Go (OTG) interface to enable USB communication.FeaturesMCU ESP32-S2 embedded, Xtensa® single-core 32-bit LX7 microprocessor, up to 240 MHz 128 KB ROM 320 KB SRAM 16 KB SRAM in RTC WiFi 802.11 b/g/n Bit rate: 802.11n up to 150 Mbps A-MPDU and A-MSDU aggregation 0.4 µs guard interval support Center frequency range of operating channel: 2412 ~ 2484 MHz Hardware Interfaces: GPIO, SPI, LCD, UART, I²C, I²S, Camera interface, IR, pulse counter, LED PWM, TWAI (compatible with ISO 11898-1), USB OTG 1.1, ADC, DAC, touch sensor, temperature sensor 40 MHz crystal oscillator 4 MB SPI flash Operating voltage/Power supply: 3.0 ~ 3.6 V Operating temperature range: –40 ~ 85 °C Dimensions: 18 × 31 × 3.3 mm Applications Generic Low-power IoT Sensor Hub Generic Low-power IoT Data Loggers Cameras for Video Streaming Over-the-top (OTT) Devices USB Devices Speech Recognition Image Recognition Mesh Network Home Automation Smart Home Control Panel Smart Building Industrial Automation Smart Agriculture Audio Applications Health Care Applications Wi-Fi-enabled Toys Wearable Electronics Retail & Catering Applications Smart POS Machines
€ 6,95
Leden € 6,26
Espressif ESP32-S2-WROVER
At the core of this module is ESP32-S2, an Xtensa® 32-bit LX7 CPU that operates at up to 240 MHz. The chip has a low-power co-processor that can be used instead of the CPU to save power while performing tasks that do not require much computing power, such as monitoring of peripherals. ESP32-S2 integrates a rich set of peripherals, ranging from SPI, I²S, UART, I²C, LED PWM, TWAITM, LCD, Camera interface, ADC, DAC, touch sensor, temperature sensor, as well as up to 43 GPIOs. It also includes a full-speed USB On-The-Go (OTG) interface to enable USB communication.FeaturesMCU ESP32-S2 embedded, Xtensa® single-core 32-bit LX7 microprocessor, up to 240 MHz 128 KB ROM 320 KB SRAM 16 KB SRAM in RTC WiFi 802.11 b/g/n Bit rate: 802.11n up to 150 Mbps A-MPDU and A-MSDU aggregation 0.4 µs guard interval support Center frequency range of operating channel: 2412 ~ 2484 MHz Hardware Interfaces: GPIO, SPI, LCD, UART, I²C, I²S, Camera interface, IR, pulse counter, LED PWM, TWAI (compatible with ISO 11898-1), USB OTG 1.1, ADC, DAC, touch sensor, temperature sensor 40 MHz crystal oscillator 4 MB SPI flash Operating voltage/Power supply: 3.0 ~ 3.6 V Operating temperature range: –40 ~ 85 °C Dimensions: 18 × 31 × 3.3 mm Applications Generic Low-power IoT Sensor Hub Generic Low-power IoT Data Loggers Cameras for Video Streaming Over-the-top (OTT) Devices USB Devices Speech Recognition Image Recognition Mesh Network Home Automation Smart Home Control Panel Smart Building Industrial Automation Smart Agriculture Audio Applications Health Care Applications Wi-Fi-enabled Toys Wearable Electronics Retail & Catering Applications Smart POS Machines
€ 7,95
Leden € 7,16
Espressif ESP32-WROOM-32
The ESP-WROOM-32, measuring 25.2 mm x 18 mm only, contains the ESP32 SoC, flash memory, precision discrete components, and PCB antenna to provide outstanding RF performance in space-constrained applications. ESP-WROOM-32 is a powerful, generic Wi-Fi + BT + BLE MCU module that targets a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming and MP3 decoding. At the core of this module is the ESP32-D0WDQ6 chip. The chip embedded is designed to be scalable and adaptive. There are two CPU cores that can be individually controlled, and the clock frequency is adjustable from 80 MHz to 240 MHz. The user may also power off the CPU and make use of the low-power co-processor to monitor the peripherals for changes or crossing of thresholds constantly. ESP32 integrates a rich set of peripherals, ranging from capacitive touch sensors, Hall sensors, SD card interface, Ethernet, high-speed SPI, UART, I²S and I²C. The integration of Bluetooth, Bluetooth LE and Wi-Fi ensures that a wide range of applications can be targeted and that the module is future proof. Using Wi-Fi allows a vast physical range and direct connection to the internet through a Wi-Fi router while using Bluetooth allows the user to conveniently connect to the phone or broadcast low energy beacons for its detection. The sleep current of the ESP32 chip is less than 5 µA, making it suitable for battery powered and wearable electronics applications. ESP32 supports a data rate of up to 150 Mbps, and 20.5 dBm output power at the antenna to ensure the broadest physical range. As such the chip does offer industry-leading specifications and the best performance for electronic integration, range, power consumption, and connectivity.
€ 9,95€ 7,95
Leden identiek
Espressif ESP32-C3-WROOM-02U-N4
De ESP32-C3-WROOM-02U is een Wi-Fi- en Bluetooth LE module voor algemeen gebruik. Het brede scala aan randapparatuur en de hoge prestaties maken deze module tot een ideale keuze voor smart homes, industriële automatisering, zorgtoepassingen, consumentenelektronica, en meer. De ESP32-C3-WROOM-02U is voorzien van een externe SPI flash en wordt geleverd met een aansluiting voor een externe antenne. De ESP32-C3-WROOM-02U werkt in een omgevingstemperatuur van –40 ? 85°C en is ingebouwd in de ESP32-C3 chip. De ESP32-C3 heeft een 32-bits RISC-V single-core processor. Hij bevat een ruime selectie aan randapparatuur, variërend van een UART, I²C, I²S, randapparatuur voor afstandsbediening, een LED PWM controller, een algemene DMA-controller, een TWAI-controller, een USB seriële/JTAG controller, een temperatuursensor, een ADC, enzovoort. Hij bevat ook SPI, Dual SPI en Quad SPI interfaces. Kenmerken Flash: 4 MB (Quad SPI) Afmetingen: 18,0 x 20,0 x 3,2 mm Downloads Datasheet
€ 7,95
Leden € 7,16
Espressif ESP32-S3-DevKitC-1U-N8R8
De ESP32-S3-DevKitC-1 is een ontwikkelboard op instapniveau dat is uitgerust met de ESP32-S3-WROOM-1U, een Wi-Fi + Bluetooth Low Energy MCU module voor algemeen gebruik die de volledige set aan Wi-Fi- en Bluetooth Low Energy functies integreert. De meeste I/O-pinnen op de module zijn uitgevoerd naar de pin-headers aan beide zijden van dit board voor eenvoudige interfacing. Ontwikkelaars kunnen hun randapparatuur aansluiten met jumperdraden, of de ESP32-S3-DevKitC-1 op een breadboard aansluiten. Kenmerken Geïntegreerde module: ESP32-S3-WROOM-1U-N8R8 Flash: 8 MB QD PSRAM: 8 MB OT SPI-spanning: 3,3 V Specificaties ESP32-S3-WROOM-1U De ESP32-S3-WROOM-1U is een krachtige generieke Wi-Fi + Bluetooth Low Energy MCU-module met een rijke set aan randapparatuur. Hij biedt versnelling voor neural netwerkcomputing en krachtige signaalverwerking. De ESP32-S3-WROOM-1U wordt geleverd met een externe antenne aansluiting. 5 V tot 3,3 V LDO Vermogensregelaar die een 5 V voeding omzet in een 3,3 V uitgang. Pin headers Alle beschikbare GPIO-pinnen (behalve de SPI-bus voor de flash) zijn uitgevoerd naar de pin-headers op het board voor eenvoudige interfacing en programmering. USB-naar-UART poort Een micro-USB poort die wordt gebruikt voor de voeding van het board, voor het flashen van toepassingen op de chip, en voor communicatie met de chip via de ingebouwde USB-naar-UART bridge. Boot knop Download knop. Als u Boot ingedrukt houdt en vervolgens op Reset drukt wordt de firmware download modus gestart voor het downloaden van firmware via de seriële poort. Reset knop Druk op deze knop om het systeem opnieuw op te starten. USB-poort Een ESP32-S3 full-speed USB OTG interface, compatibel met USB 1.1 specificaties. Deze interface wordt gebruikt voor de voeding van het board, voor het flashen van toepassingen op de chip, voor communicatie met de chip via USB 1.1 protocollen, en voor JTAG-foutopsporing. USB-naar-UART bridge Deze single USB-naar-UART bridgechip biedt overdrachtssnelheden tot 3 Mbps. RGB LED Adresseerbare RGB LED, aangedreven door GPIO38. 3,3 V LED Wordt ingeschakeld wanneer de USB-voeding op het board is aangesloten. Downloads Pin lay-out
€ 29,95
Leden € 26,96
Elektor Publishing Das ESP32-Praxisbuch
Das ESP32-Praxisbuch
€ 39,80
Leden identiek
Espressif ESP32-S2-Saola-1M Development Board
ESP32-S2-Saola-1M is a small-sized ESP32-S2 based development board. Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S2-Saola-1M on a breadboard.ESP32-S2-Saola-1M is equipped with the ESP32-S2-WROOM module, a powerful, generic Wi-Fi MCU module that has a rich set of peripherals. It is an ideal choice for a wide variety of application scenarios relating to Internet of Things (IoT), wearable electronics and smart home. The board a PCB antenna and features a 4 MB external SPI flash.FeaturesMCU ESP32-S2 embedded, Xtensa® single-core 32-bit LX7 microprocessor, up to 240 MHz 128 KB ROM 320 KB SRAM 16 KB SRAM in RTC WiFi 802.11 b/g/n Bit rate: 802.11n up to 150 Mbps A-MPDU and A-MSDU aggregation 0.4 µs guard interval support Center frequency range of operating channel: 2412 ~ 2484 MHz Hardware Interfaces: GPIO, SPI, LCD, UART, I²C, I²S, Camera interface, IR, pulse counter, LED PWM, TWAI (compatible with ISO 11898-1), USB OTG 1.1, ADC, DAC, touch sensor, temperature sensor 40 MHz crystal oscillator 4 MB SPI flash Operating voltage/Power supply: 3.0 ~ 3.6 V Operating temperature range: –40 ~ 85 °C Dimensions: 18 × 31 × 3.3 mm Applications Generic Low-power IoT Sensor Hub Generic Low-power IoT Data Loggers Cameras for Video Streaming Over-the-top (OTT) Devices USB Devices Speech Recognition Image Recognition Mesh Network Home Automation Smart Home Control Panel Smart Building Industrial Automation Smart Agriculture Audio Applications Health Care Applications Wi-Fi-enabled Toys Wearable Electronics Retail & Catering Applications Smart POS Machines
€ 29,95
Leden € 26,96
Espressif ESP32-S2-Saola-1R Development Board
ESP32-S2-Saola-1R is a small-sized ESP32-S2 based development board. Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S2-Saola-1R on a breadboard.ESP32-S2-Saola-1R is equipped with the ESP32-S2-WROVER module, a powerful, generic Wi-Fi MCU module that has a rich set of peripherals. It is an ideal choice for a wide variety of application scenarios relating to Internet of Things (IoT), wearable electronics and smart home. The board a PCB antenna and features a 4 MB external SPI flash and an additional 2 MB SPI Pseudo static RAM (PSRAM).FeaturesMCU ESP32-S2 embedded, Xtensa® single-core 32-bit LX7 microprocessor, up to 240 MHz 128 KB ROM 320 KB SRAM 16 KB SRAM in RTC WiFi 802.11 b/g/n Bit rate: 802.11n up to 150 Mbps A-MPDU and A-MSDU aggregation 0.4 µs guard interval support Center frequency range of operating channel: 2412 ~ 2484 MHz Hardware Interfaces: GPIO, SPI, LCD, UART, I²C, I²S, Camera interface, IR, pulse counter, LED PWM, TWAI (compatible with ISO 11898-1), USB OTG 1.1, ADC, DAC, touch sensor, temperature sensor 40 MHz crystal oscillator 4 MB SPI flash Operating voltage/Power supply: 3.0 ~ 3.6 V Operating temperature range: –40 ~ 85 °C Dimensions: 18 × 31 × 3.3 mm Applications Generic Low-power IoT Sensor Hub Generic Low-power IoT Data Loggers Cameras for Video Streaming Over-the-top (OTT) Devices USB Devices Speech Recognition Image Recognition Mesh Network Home Automation Smart Home Control Panel Smart Building Industrial Automation Smart Agriculture Audio Applications Health Care Applications Wi-Fi-enabled Toys Wearable Electronics Retail & Catering Applications Smart POS Machines
€ 22,95
Leden € 20,66
Espressif ESP32-Cam-CH340 Development Board
Features Product model: HW-818 Working voltage: DC 5V Product size: 27mm x 48.5 mm x 4.5 mm / 1.06” x 1.9” x 0.17” SPI Flash: Default 32Mbit RAM: Internal 520KB + External 4MPSRAM Bluetooth: Bluetooth 4.2 BR/EDR and BLE standards Wi-Fi: 802 II b/g/n/e/i Support interfaces: UART, SPI, I2C, PWM Supporting TF Card: Maximum Supporting 4G IO port: 9 Serial port rate: default 115200 BPS Image output format: JPEG (OV2640 only), BMP, GRAYSCALE Spectrum range: 2412-2484 MHz Antenna form: board PCB antenna, gain 2dBi Transmitting power: 802.l1b: 17 + 2dBm (1lMbps) 802.l1g:14+2dBm (54Mbps) 802.l1n:13+2dBm (MCS7)
€ 11,95
Leden € 10,76